Home › Drivetrain › CLUTCH › CLUTCH PEDAL (for LHD) › from 2020.08
RM3620E _52 Drivetrain _076045 CLUTCH _0370081 CLUTCH PEDAL(for LHD) A

CLUTCH  CLUTCH PEDAL(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during clutch pedal removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Battery terminal is disconnected/reconnected Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system for M20A-FKS:(Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B475753

Be sure to read precaution thoroughly before servicing.



NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


CAUTION:
·
B394718

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 3.REMOVE KNEE AIRBAG ASSEMBLY (for Driver Side)

Hide 31453A 4.REMOVE CLUTCH MASTER CYLINDER PUSH ROD CLEVIS WITH HOLE PIN

C403349

a.

Remove the clutch master cylinder push rod clevis with hole pin and clip.


Hide 55107A 5.REMOVE CLUTCH PEDAL SUPPORT SUB-ASSEMBLY

a.
C403350

Disconnect the 2 connectors and clamp.


b.
C403351

Remove the bolt, 2 nuts and clutch pedal support sub-assembly.


Hide 89280 6.REMOVE CLUTCH PEDAL STROKE SENSOR ASSEMBLY

Hide 88280A 7.REMOVE CLUTCH START SWITCH ASSEMBLY

a.
C403355

Remove the nut and clutch start switch assembly.


Hide 31301A 8.REMOVE CLUTCH PEDAL SPRING

C403353

a.

Remove the clutch pedal spring.


Hide 31301 9.REMOVE CLUTCH PEDAL SUB-ASSEMBLY

a.
C403356

Remove the bolt, nut and clutch pedal sub-assembly from the clutch pedal support sub-assembly.


Hide 31353 10.REMOVE CLUTCH PEDAL SPRING HOLDER

C403357

a.

Remove the clutch pedal spring holder.


Hide 31324A 11.REMOVE CLUTCH PEDAL SHAFT COLLAR

C403358

a.

Remove the 2 bushes and clutch pedal shaft collar.


Hide 31301P 12.REMOVE CLUTCH PEDAL TURNOVER BUSH

C403359

a.

Remove the clutch pedal turnover bush from the clutch pedal sub-assembly.


Hide 31321 13.REMOVE CLUTCH PEDAL PAD

a.
C403360

Remove the clutch pedal pad from the clutch pedal sub-assembly.


Hide 14.DISCONNECT CLUTCH PEDAL BRACKET SUB-ASSEMBLY

a.
C405016

Disconnect the clutch pedal bracket sub-assembly from the clutch pedal support sub-assembly.