Home › Drivetrain › CLUTCH › CLUTCH PEDAL (for RHD) › from 2020.08
RM3620E _52 Drivetrain _076045 CLUTCH _0370082 CLUTCH PEDAL(for RHD) A

CLUTCH  CLUTCH PEDAL(for RHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during clutch pedal removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Battery terminal is disconnected/reconnected Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system for M20A-FKS:(Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.


PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B475753

Be sure to read precaution thoroughly before servicing.



NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


CAUTION:
·
B394718

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 3.REMOVE KNEE AIRBAG ASSEMBLY (for Driver Side)

Hide 31453A 4.REMOVE CLUTCH MASTER CYLINDER PUSH ROD CLEVIS WITH HOLE PIN

C403503

a.

Remove the clutch master cylinder push rod clevis with hole pin and clip.


Hide 55107A 5.REMOVE CLUTCH PEDAL SUPPORT SUB-ASSEMBLY

a.
C403504

Disconnect the 2 connectors and 2 clamps.


b.
C403505

Remove the 4 nuts and clutch pedal support sub-assembly.

CAUTION:

While taking care not to pinch your hand, depress the clutch pedal.


NOTICE:

When removing the clutch pedal, do not damage the No. 1 air duct.



Hide 89280 6.REMOVE CLUTCH PEDAL STROKE SENSOR ASSEMBLY

Hide 88280A 7.REMOVE CLUTCH START SWITCH ASSEMBLY

a.
C403508

Remove the nut and clutch start switch assembly.


Hide 31301A 8.REMOVE CLUTCH PEDAL SPRING

C403506

a.

Remove the clutch pedal spring.


Hide 31301 9.REMOVE CLUTCH PEDAL SUB-ASSEMBLY

a.
C403509

Remove the bolt, nut and clutch pedal sub-assembly from the clutch pedal support sub-assembly.


Hide 31353 10.REMOVE CLUTCH PEDAL SPRING HOLDER

C403510

a.

Remove the clutch pedal spring holder.


Hide 31324A 11.REMOVE CLUTCH PEDAL SHAFT COLLAR

C403512

a.

Remove the 2 bushes and clutch pedal shaft collar.


Hide 31301P 12.REMOVE CLUTCH PEDAL TURNOVER BUSH

C403513

a.

Remove the clutch pedal turnover bush from the clutch pedal sub-assembly.


Hide 31321 13.REMOVE CLUTCH PEDAL PAD

a.
C403511

Remove the clutch pedal pad from the clutch pedal sub-assembly.