Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT AXLE HUB › from 2020.08
RM3620E _52 Drivetrain _076176 AXLE AND DIFFERENTIAL _0371053 FRONT AXLE HUB A

AXLE AND DIFFERENTIAL  FRONT AXLE HUB  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front axle hub assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model:)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)
Front wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model:)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Front wheel alignment adjustment
·

Perform reset memory

·

Perform acceleration sensor zero point calibration and store system information memorization.


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)

HINT:
·

Use the same procedure for the RH and LH sides.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.DISABLE BRAKE CONTROL (w/o Vacuum Brake Booster)

Hide 2.REMOVE FRONT WHEEL

Hide 43502H 3.REMOVE FRONT AXLE SHAFT NUT LH

a.
C407528E01
2.333,1.417 2.583,1.083 2.583,1.083 2.75,1.083 false 2.833,1 3.292,1.198 0.458,0.198 10 false SST

Using SST and a hammer, unstake the staked part of the front axle shaft nut.

SST
09930-00010  (09931-00010, 09931-00020)

NOTICE:

Loosen the staked part of the front axle shaft nut completely, otherwise the screw of the drive shaft may be damaged.



b.

While applying the brakes, remove the front axle shaft nut.


Hide 89543 4.DISCONNECT FRONT SPEED SENSOR LH

a.
C397644

Remove the bolt and disconnect the front speed sensor and front flexible hose from the front shock absorber assembly.

NOTICE:

Be sure to separate the front speed sensor and front flexible hose from the front shock absorber assembly completely.



b.
C397650

Remove the bolt, disengage the clamp and disconnect the front speed sensor from the front shock absorber assembly and steering knuckle.

NOTICE:
·

Prevent foreign matter from contacting the sensor tip.

·

Be careful not to damage the front speed sensor.

·

Clean the speed sensor installation hole and the contact surfaces every time the front speed sensor is removed.




Hide 45470 5.DISCONNECT TIE ROD ASSEMBLY LH

Hide 6.DISCONNECT FRONT DISC BRAKE CALIPER ASSEMBLY LH

Hide 43512 7.REMOVE FRONT DISC

·

except 2-Pot Caliper: Click here


Hide 48069 8.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.
C397651

Remove the bolt and 2 nuts and disconnect the front lower No. 1 suspension arm sub-assembly from the front lower ball joint assembly.


Hide 43420 9.DISCONNECT FRONT DRIVE SHAFT ASSEMBLY LH

a.
C397652C01
2.781,0.406 3.188,0.406 3.188,0.406 3.188,1.573 true 2.927,0.667 3.188,0.667 true 3.115,1.615 3.396,1.823 0.281,0.208 10 false *a
*a Matchmark


Place matchmarks on the front axle hub LH and front drive shaft assembly LH as shown in the illustration.


b.
C397653

Using a plastic hammer, disconnect the front drive shaft assembly from the front axle assembly.

NOTICE:
·

Do not damage the front drive shaft outboard joint boot.

·

Do not push the front axle assembly towards the outside of the vehicle any further than necessary.



HINT:

If it is difficult to separate the front drive shaft assembly from the front axle assembly, tap the end of the front drive shaft assembly using a brass bar and a hammer.



Hide 10.REMOVE FRONT AXLE ASSEMBLY LH

a.
C397654

Remove the 2 bolts, 2 nuts and front axle assembly from the front shock absorber assembly.

NOTICE:

When removing the nuts, keep the bolts from rotating.



Hide 43502C 11.REMOVE FRONT AXLE HUB SUB-ASSEMBLY LH

a.
C397655

Secure the front axle assembly between aluminum plates in a vise.

NOTICE:

Do not overtighten the vise.



b.

Remove the 4 bolts, front axle hub sub-assembly and front disc brake dust cover from the steering knuckle.

NOTICE:
·

Do not drop the front axle hub sub-assembly.

·

Be careful not to damage the speed sensor rotor or contact surfaces.

·

Do not allow foreign matter to contact the speed sensor rotor or contact surfaces.