Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for LHD without Vacuum Brake Booster) › from 2020.08
RM3620E _54 Brake _076411 BRAKE SYSTEM (OTHER) _0377038 BRAKE BOOSTER(for LHD without Vacuum Brake Booster) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for LHD without Vacuum Brake Booster)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during brake booster with master cylinder assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)
Replacement of skid control ECU (brake booster with master cylinder assembly)
·

Perform initialization and calibration of the linear solenoid valve

·

Perform yaw rate and acceleration sensor zero point calibration


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.


Hide 2. DISABLE BRAKE CONTROL

Hide 3.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 5.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 73900 6.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 87211 7.REMOVE NO. 2 AIR DUCT

Hide 84340 8.REMOVE STOP LIGHT SWITCH ASSEMBLY

Hide 10.SEPARATE WIRE HARNESS

a.
C409059

Disconnect the connector from the brake pedal stroke sensor assembly.


b.

Disengage the 2 clamps to separate the wire harness from the brake pedal support assembly.


Hide 47220D 12.SEPARATE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

a.
C408163

Remove the 2 nuts and separate the brake master cylinder reservoir assembly.


Hide 47235G 13.DISCONNECT NO. 2 RESERVOIR HOSE

a.
C408161

Slide the clip and disconnect the No. 2 reservoir hose from the brake booster with master cylinder assembly.


Hide 47234L 14.DISCONNECT NO. 1 RESERVOIR HOSE

a.
C408160

Slide the clip and disconnect the No. 1 reservoir hose from the brake booster with master cylinder assembly.


Hide 44571A 15.DISCONNECT NO. 1 BRAKE ACTUATOR HOSE

a.
C408162

Slide the clip and disconnect the brake actuator hose from the brake master cylinder reservoir assembly.


Hide 16.REMOVE BRAKE MASTER CYLINDER RESERVOIR WITH RESERVOIR HOSE

a.

Remove the brake master cylinder reservoir with reservoir hose


Hide 47233 17.REMOVE RESERVOIR BRACKET

a.
C408164

Remove the bolt, 2 nuts and reservoir bracket.


Hide 44551C 18.SEPARATE NO. 1 BRAKE ACTUATOR TUBE

a.
C408174

Remove the 2 nuts and separate the No. 1 brake actuator tube from the vehicle body.


Hide 47314 19.DISCONNECT NO. 4 FRONT BRAKE TUBE

a.
C408176

Using a union nut wrench, disconnect the No. 4 front brake tube.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




Hide 47210L 20.REMOVE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

a.
C408165C01
0,0 0,0 false
V113147

Release the lock lever
V113148

Disconnect the connector


Disengage the clamp to separate the wire harness.


b.

Release the lock lever and disconnect the connector from the brake booster with master cylinder assembly.

NOTICE:

Be careful not to allow brake fluid to enter the removed connector.



c.
C408167C01
0.938,0.438 1.104,0.438 1.104,0.438 1.26,0.688 true 2.021,1.146 2.323,1.792 2.323,1.792 2.49,1.792 true 1.938,0.552 2.271,0.219 2.271,0.219 2.438,0.219 true 1.5,1.375 1.667,1.375 1.667,1.375 1.99,0.958 true 1.594,0.948 1.76,0.948 1.76,0.948 1.927,0.781 true 2.5,0.135 2.74,0.333 0.24,0.198 10 true *a 1.406,0.854 1.625,1.01 0.219,0.156 10 true *b 1.313,1.281 1.542,1.448 0.229,0.167 10 true *c 2.542,1.698 2.792,1.865 0.25,0.167 10 true *d 0.729,0.333 0.979,0.5 0.25,0.167 10 true *e
*a To Front Wheel Cylinder LH
*b To Rear Wheel Cylinder RH
*c To Brake Booster Pump Assembly
*d To Rear Wheel Cylinder LH
*e To Front Wheel Cylinder RH


Using a union nut wrench, disconnect the 5 brake lines from the brake booster with master cylinder assembly.


d.

Use tags or make a memo to identify the places to reconnect.


e.
C408175

Disengage the 8 clamps to remove the 2 brake tube clamps from the brake lines.


f.
C409061

Disengage the 4 clamps to remove the brake tube clamp from the brake lines.


g.

Disengage the clamp and remove the brake tube clamp from the vehicle body.


h.
C409062

Disengage the clamp to remove the No. 4 front brake tube with brake tube clamp from the brake line.


i.
C408178

Disengage the clamp to remove the brake tube clamp from the No. 4 front brake tube.


j.
C408170C01
1.719,2.646 2.219,2.646 false 1.438,3.833 0.75,4.125 0.75,4.125 1.385,4.125 true 1.719,3.063 0.583,2.583 0.583,2.583 1.313,3.094 true 2.74,3.469 2.917,3.677 2.917,3.677 3.083,3.677 false 2.406,3.583 2.698,3.938 2.698,3.938 2.865,3.938 false 2.281,2.583 2.594,2.74 0.313,0.156 10 false *1 0.396,2.469 0.708,2.625 0.313,0.156 10 false *2 3.146,3.615 3.427,3.823 0.281,0.208 10 false *3 2.917,3.854 3.229,4.01 0.313,0.156 10 false *4 0.563,4.042 0.875,4.198 0.313,0.156 10 false *5
*1 Connector Portion
*2 Union
*3 Push Rod Clevis
*4 Boot
*5 Front No. 2 Brake Tube


Remove the 4 nuts and brake booster with master cylinder assembly.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not carry the brake booster with master cylinder assembly by the portion shown in the illustration.




Hide 44785C 21.REMOVE BRAKE BOOSTER GASKET