Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER PUMP (for LHD without Vacuum Brake Booster) › from 2020.08
RM3620E _54 Brake _076411 BRAKE SYSTEM (OTHER) _0377041 BRAKE BOOSTER PUMP(for LHD without Vacuum Brake Booster) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER PUMP(for LHD without Vacuum Brake Booster)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during brake booster pump assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)

NOTICE:

After the power switch is turned off, the radio receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


NOTICE:
·

After the power switch is turned off, the radio receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.


Hide 2. DISABLE BRAKE CONTROL

Hide 3.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 5.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 44572C 6.DISCONNECT NO. 2 BRAKE ACTUATOR HOSE

a.
C407914

Slide the clip and disconnect the No. 2 brake actuator hose from the No. 1 brake actuator tube.


Hide 473A1 7.DISCONNECT ACCUMULATOR TO BRAKE MASTER CYLINDER TUBE

a.
C407915

Using a union nut wrench, disconnect the accumulator to brake master cylinder tube from the brake booster pump assembly.

NOTICE:
·

Do not kink or damage the accumulator to brake master cylinder tube.

·

Do not allow any foreign matter such as dirt or dust to enter the accumulator to brake master cylinder tube from the connecting parts.




Hide 8.REMOVE BRAKE BOOSTER PUMP ASSEMBLY WITH BRACKET

a.
C407916C01
0,0 0,0 false
V113147

Release the lock lever
V113148

Disconnect the connector


Release the lock lever and disconnect the connector from the brake booster pump assembly as shown in the illustration.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.



b.
C407917C01
2.073,4.385 2.427,4.385 true 1.26,4.479 1.448,4.479 1.448,4.479 1.448,4.146 false 2.229,3.719 2.583,3.719 true 1.188,3.792 1.188,3.26 1.188,3.26 1.021,3.26 true 2.646,3.646 2.958,3.802 0.313,0.156 10 false *a 2.469,4.292 2.781,4.448 0.313,0.156 10 false *b 1.073,4.385 1.354,4.563 0.281,0.177 10 false *c 0.833,3.156 1.083,3.385 0.25,0.229 10 false *d
*a Union
*b Connector
*c Wire Harness
*d Stud


Remove the nut, 2 bolts and brake booster pump assembly with bracket from the vehicle body.

NOTICE:
·

Do not apply excessive force to the brake lines.

·

Do not carry the brake booster pump assembly by the parts shown in the illustration.

·

Do not drop the brake booster pump assembly when carrying it.

·

Do not a brake booster pump assembly that has been dropped.

·

Be careful not to allow brake fluid to enter the connector.




Hide 44572C 9.REMOVE NO. 2 BRAKE ACTUATOR HOSE

a.
C407919

Slide the clip and remove the No. 2 brake actuator hose from the brake booster pump assembly.


Hide 47070 10.REMOVE BRAKE BOOSTER PUMP ASSEMBLY

a.
C407920

Disengage the 2 clamps to separate the wire harness from the brake actuator bracket assembly.


b.
C407921

Remove the nut to separate the brake booster pump from the brake actuator bracket assembly.


c.
C407922C01
2.135,0.354 2.302,0.354 2.302,0.354 2.719,0.771 false 0.427,0.917 0.594,0.917 0.594,0.917 1.01,1.333 false 0.271,1.896 0.438,1.896 0.438,1.896 0.646,2.177 false 0.167,2.385 0.438,2.938 0.438,2.938 0.604,2.938 false 1.917,0.271 2.146,0.542 0.229,0.271 10 false *1 0.219,0.823 0.531,0.979 0.313,0.156 10 false *2 0.021,1.802 0.333,1.958 0.313,0.156 10 false *3 0.698,2.865 1.01,3.021 0.313,0.156 10 false *4
*1 Brake Booster Pump
*2 Brake Actuator Bracket Assembly
*3 Brake Booster Pump Bushing
*4 No. 2 Brake Actuator Case Collar


Remove the brake booster pump from the brake actuator bracket assembly.


d.

Remove the brake booster pump bushing and No. 2 brake actuator case collar from the brake actuator bracket assembly.


e.
C380676

Remove the 2 brake booster pump collars and 2 brake booster pump bushings from the brake booster pump assembly.

HINT:

Perform this procedure only when replacement of the brake booster pump collars or brake booster pump bushings is necessary.