The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during brake booster pump assembly removal/installation are shown below.
After the power switch is turned off, the radio receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.
After the power switch is turned off, the radio receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.
While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.
2. DISABLE BRAKE CONTROL
Click hereBrake>BRAKE (REAR)>REAR BRAKE>REMOVAL
3.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
55704B
4.REMOVE COWL VENTILATOR PANEL SUB-ASSEMBLY
5.DRAIN BRAKE FLUID
If brake fluid leaks onto any painted surface, immediately wash it off.
44572C
6.DISCONNECT NO. 2 BRAKE ACTUATOR HOSE
Slide the clip and disconnect the No. 2 brake actuator hose from the No. 1 brake actuator tube.
44551C
7.SEPARATE NO. 1 BRAKE ACTUATOR TUBE
Remove the 2 nuts to separate the No. 1 brake actuator tube.
473A1
8.DISCONNECT ACCUMULATOR TO BRAKE MASTER CYLINDER TUBE
Using a union nut wrench, disconnect the accumulator to brake master cylinder tube from the brake booster pump assembly.
Do not kink or damage the accumulator to brake master cylinder tube.
Do not allow any foreign matter such as dirt or dust to enter the accumulator to brake master cylinder tube from the connecting parts.
47315
9.SEPARATE NO. 5 FRONT BRAKE TUBE
Using a union nut wrench, disconnect the No. 5 front brake tube from the brake tube way.
Disengage the 3 clamps to separate the brake brake tube clamp from the brake lines.
Remove the bolt and brake tube clamp from the vehicle body.
Disengage the clamp to separate the brake tube clamp from the No. 5 front brake tube.
10.REMOVE BRAKE BOOSTER PUMP ASSEMBLY WITH BRACKET
|
Release the lock lever |
|
Disconnect the connector |
Release the lock lever and disconnect the connector from the brake booster pump assembly as shown in the illustration.
Be careful not to allow any brake fluid to enter the connector.
| *a | Union |
| *b | Connector |
| *c | Wire Harness |
| *d | Stud |
Remove the nut, 2 bolts and brake booster pump assembly with bracket from the vehicle body.
Do not apply excessive force to the brake lines.
Do not carry the brake booster pump assembly by the parts shown in the illustration.
Do not drop the brake booster pump assembly when carrying it.
Do not a brake booster pump assembly that has been dropped.
Be careful not to allow brake fluid to enter the connector.
44572C
11.REMOVE NO. 2 BRAKE ACTUATOR HOSE
Slide the clip and remove the No. 2 brake actuator hose from the brake booster pump assembly.
47070
12.REMOVE BRAKE BOOSTER PUMP ASSEMBLY
Disengage the clamp to remove the brake tube clamp from the brake actuator bracket assembly.
Disengage the 2 clamps to separate the wire harness from the brake actuator bracket assembly.
Remove the nut to separate the brake booster pump from the brake actuator bracket assembly.
| *1 | Brake Booster Pump |
| *2 | Brake Actuator Bracket Assembly |
| *3 | Brake Booster Pump Bushing |
| *4 | No. 2 Brake Actuator Case Collar |
Remove the brake booster pump from the brake actuator bracket assembly.
Remove the brake booster pump bushing and No. 2 brake actuator case collar from the brake actuator bracket assembly.
Remove the 2 brake booster pump collars and 2 brake booster pump bushings from the brake booster pump assembly.
Perform this procedure only when replacement of the brake booster pump collars or brake booster pump bushings is necessary.