Home › Engine / Hybrid System › A25A-FKS (FUEL) › FUEL FILTER (w/o Canister Pump Module) › from 2020.08
RM3620E _51 Engine / Hybrid System _076683 A25A-FKS FUEL _0378738 FUEL FILTER(w/o Canister Pump Module) A

A25A-FKS FUEL  FUEL FILTER(w/o Canister Pump Module)  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel sub-tank sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Battery terminal is disconnected/reconnected Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system (Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Reset back door close position Power back door system (Click here)
Power back door initialization Power door lock control system (Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



NOTICE:

Do not disconnect the tube shown in the illustration when disassembling the fuel suction tube with pump and gauge assembly. Doing so will cause reassembly of the fuel suction tube with pump and gauge assembly to be impossible as the tube is pressed into the fuel suction plate sub-assembly.

Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 77020A 3.REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

Hide 77103 5.REMOVE FUEL SUB-TANK SUB-ASSEMBLY

a.
A433835

Detach the 2 claws and 2 clamps and disconnect the fuel suction tube from the fuel sub-tank sub-assembly.


b.
A433836

Remove the O-ring from the fuel sub-tank sub-assembly.


c.
A433837

Detach the 4 claws and disconnect the sub-assembly support from the fuel sub-tank sub-assembly.


d.
A436273C01
0,0 0,0 false
V100135

Pull
V100136

Slide


Detach the claw and slide the fuel sub-tank sub-assembly and disconnect it from the fuel suction plate sub-assembly.


Hide 77103 6.INSTALL FUEL SUB-TANK SUB-ASSEMBLY

a.
A436274C01
2.427,1.99 2.292,1.99 2.292,1.99 1.969,1.438 true 2.646,0.365 2.51,0.365 2.51,0.365 2.073,1.333 true 2.667,0.26 2.854,0.427 0.188,0.167 10 true *a 2.458,1.896 2.625,2.073 0.167,0.177 10 true *b
*a Installation Hole
*b Protrusion
V100135

Slide


Align the protrusion of the fuel sub-tank sub-assembly with the installation hole of the fuel suction plate sub-assembly and slide the fuel sub-tank sub-assembly to install the fuel suction plate sub-assembly.


b.

Attach the 4 claws and connect the sub-assembly support to the fuel sub-tank sub-assembly.


c.

Apply gasoline to a new O-ring.


d.
A433865

Install the O-ring to the fuel suction tube.


e.

Attach the 2 claws and 2 clamps and connect the fuel suction tube to the fuel sub-tank sub-assembly.


Hide 77020A 8.INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

Hide 9.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION