Home › Engine / Hybrid System › M20A-FKS (ENGINE MECHANICAL) › CYLINDER BLOCK › from 2020.08
RM3620E _51 Engine / Hybrid System _076500 M20A-FKS ENGINE MECHANICAL _0372440 CYLINDER BLOCK A

M20A-FKS ENGINE MECHANICAL  CYLINDER BLOCK  DISASSEMBLY  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during cylinder block removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

*2: w/ Gasoline Particulate Filter

Battery terminal is disconnected/reconnected Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system (Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*1
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration DTC P063051 is output (Click here)
ECU communication ID registration Engine start function See Service Bulletin for the registration method.
for M20A-FKS:

GPF Deposition Values*2

-

GPF deposition values save

-

GPF deposition values write



·

MIL comes on

·

Deterioration of fuel efficiency


(Click here)
for K120:
·

Perform reset memory

·

Perform road test to allow TCM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)
for K120F:
·

Perform reset memory

·

Perform road test to allow TCM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)
·

Throttle body with motor assembly

·

Cam timing control motor with EDU assembly (Including removal and installation)

·

Camshaft timing gear assembly (Including removal and installation)

·

Cylinder head sub-assembly

·

Camshaft (for intake or exhaust camshaft)

·

Camshaft timing exhaust gear assembly

·

Piston or piston ring

·

Mass air flow meter sub-assembly

·

Port fuel injector assembly

·

Direct fuel injector assembly

·

Fuel pump (for low pressure side)

·

Fuel pump assembly (for high pressure side)

·

Fuel pressure sensor (for low pressure side)

·

Fuel pressure sensor (for high pressure side)

·

Air fuel ratio sensor (sensor 1)

·

Air fuel ratio sensor (sensor 2)

·

Engine coolant temperature sensor

·

Spark plug

·

Ignition coil assembly

·

EGR valve assembly

·

Air intake system parts

·

Gas leaks from exhaust system

·

Knock control sensor


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of continuously variable transaxle assembly Air bleed oil pump with motor assembly Stop and start system (Click here)
for K120, K120F:
·

Input transaxle compensation code into TCM

·

Perform reset memory

·

Deceleration sensor zero point calibration

·

CVT oil pressure calibration

·

Perform road test to allow TCM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


for K120:(Click here)
for K120F:(Click here)
Suspension, tires, etc.
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (for Gasoline model) (Click here)
Television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system (for Gasoline model) (Click here)
Front wheel alignment adjustment
1.

Perform reset memory

2.

Perform acceleration sensor zero point calibration and store system information memorization.


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)
Front bumper assembly (Including removal and installation)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (for Gasoline model) (Click here)
Front television camera view adjustment Panoramic view monitor system (for Gasoline model) (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.


PROCEDURE

Hide 12211 1.REMOVE NO. 1 VENTILATION CASE

CAUTION:

Do not disassembly except if the No. 1 ventilation case to be damaged.


a.
A425018

Remove the 4 bolts and No. 1 ventilation case from the cylinder block sub-assembly.


b.
A425019

Remove the 3 oil separator gaskets from the No. 1 ventilation case.


Hide 11432R 2.REMOVE CYLINDER BLOCK WITH HEAD STRAIGHT SCREW PLUG (w/o Oil Cooler)

a.
A433301

Using a 10 mm hexagon socket wrench, remove the cylinder block with head straight screw plug and gasket from the cylinder block sub-assembly.


Hide 3.INSPECT CONNECTING ROD THRUST CLEARANCE

a.
A433302

Using a dial indicator, measure the thrust clearance while moving the connecting rod sub-assembly back and forth.

Standard Thrust Clearance:

0.160 to 0.512 mm (0.00630 to 0.0202 in.)


Maximum Thrust Clearance:

0.512 mm (0.0202 in.)


HINT:

If the thrust clearance is more than the maximum, replace the connecting rod. If necessary, replace the crankshaft.



Hide 4.INSPECT CONNECTING ROD OIL CLEARANCE

a.
A433303C01
0.708,0.615 0.979,0.26 true 1,0.094 1.302,0.313 0.302,0.219 10 false *a
*a Alignment Mark


Note the alignment marks on the connecting rod and connecting rod cap so that they can be reinstalled to their original locations.


b.
A433304

Using an E12 "TORX" socket wrench, remove the 2 connecting rod bolts and connecting rod cap.

HINT:

Keep the connecting rod bearing and connecting rod cap together.



c.

Clean the crank pin and connecting rod bearing.


d.

Check the crank pin and connecting rod bearing for pitting and scratches.

HINT:

If the crank pin or connecting rod bearing is damaged, replace the connecting rod bearings. If necessary, replace the crankshaft.



e.
A433305C01
1.635,0.615 0.813,0.458 true 0.635,0.344 0.948,0.563 0.313,0.219 10 false *a
*a Plastigage


Lay a strip of Plastigage on the crank pin.


f.
A433306C01
1.521,0.833 0.802,0.615 true 0.625,0.5 0.875,0.781 0.25,0.281 10 false *a
*a Front Mark


Check that the front mark of the connecting rod cap is facing the correct direction, and install the connecting rod cap to the connecting rod.


g.
A433307

Apply a light coat of engine oil to the threads and under the heads of the 2 connecting rod bolts.


h.

Using an E12 "TORX" socket wrench, install and alternately tighten the 2 connecting rod bolts in several steps.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)


i.
A400558C01
2.26,0.802 2.531,0.385 2.531,0.385 2.677,0.385 false 1.396,0.479 1.854,0.677 0.458,0.198 10 false *b 2.729,0.281 3.042,0.479 0.313,0.198 10 false *a
*a Paint Mark
*b 90°
V100135

Front of Engine


Mark the front of each connecting rod bolt with paint.


j.

Tighten the connecting rod bolts 90° as shown in the illustration.

NOTICE:

Do not turn the crankshaft during the measurement.



k.

Remove the 2 connecting rod bolts and connecting rod cap.

HINT:

Keep the connecting rod bearing and connecting rod cap together.



l.
A433308C01
1.677,0.969 0.969,0.667 true 1.375,3.167 0.719,3.615 0.719,3.615 1.26,4.208 true 1.385,3.615 0.74,3.615 true 0.802,0.542 1.083,0.708 0.281,0.167 10 false *a 0.542,3.573 0.854,3.729 0.313,0.156 10 false *b
*a Plastigage
*b 1, 2 or 3 Mark


Measure the Plastigage at its widest point.

Standard Oil Clearance:

0.032 to 0.065 mm (0.00126 to 0.00256 in.)


Maximum Oil Clearance:

0.065 mm (0.00256 in.)


HINT:
·

If the oil clearance is more than the maximum, replace the connecting rod bearings. If necessary, replace the crankshaft.

·

If replacing a connecting rod bearing, select a new one with the same number as marked on the connecting rod cap. There are 3 sizes of standard connecting rod bearings, marked "1", "2" or "3" accordingly.



Standard Connecting Rod Big End Inside Diameter:
Mark Specified Condition
1 51.000 to 51.008 mm (2.00787 to 2.00818 in.)
2 51.008 to 51.016 mm (2.00818 to 2.00850 in.)
3 51.016 to 51.024 mm (2.00850 to 2.00881 in.)


Standard Connecting Rod Bearing Center Wall Thickness:
Mark Specified Condition
1 1.483 to 1.487 mm (0.058386 to 0.058543 in.)
2 1.487 to 1.491 mm (0.058543 to 0.058701 in.)
3 1.491 to 1.495 mm (0.058701 to 0.058858 in.)


Standard Crank Pin Diameter:

47.992 to 48.000 mm (1.88945 to 1.88976 in.)


NOTICE:

Remove the Plastigage completely after the measurement.



m.

Perform the inspection above for each cylinder.


Hide 5.REMOVE PISTON WITH CONNECTING ROD

a.
A426844C01
1.333,1.094 1.552,1.042 false 1.583,0.938 1.896,1.094 0.313,0.156 10 false *a
*a Ridge Reamer


Using a ridge reamer, remove all the carbon from the top of each cylinder.


b.

Remove the 8 connecting rod bolts, 4 connecting rod caps and 4 connecting rod bearings.


c.

Push the 4 pistons, 4 connecting rods and 4 connecting rod bearings out through the top of the cylinder block sub-assembly.

HINT:
·

Keep the connecting rod bearings, connecting rods and connecting rod caps together.

·

Arrange the removed parts in such a way that they can be reinstalled to their original locations.




Hide 6.REMOVE CONNECTING ROD BEARING

a.

Remove the 8 connecting rod bearings from the 4 connecting rods and 4 connecting rod caps.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 7.INSPECT CRANKSHAFT THRUST CLEARANCE

a.
A433309

Using a dial indicator, measure the crankshaft thrust clearance while prying the crankshaft back and forth with a screwdriver.

Standard Thrust Clearance:

0.02 to 0.22 mm (0.000787 to 0.00866 in.)


Maximum Thrust Clearance:

0.22 mm (0.00866 in.)


HINT:

If the thrust clearance is more than the maximum, replace the crankshaft thrust washers as a set. If necessary, replace the crankshaft.


Standard Thrust Washer Thickness:

2.415 to 2.470 mm (0.0951 to 0.0972 in.)



Hide 13411 8.REMOVE CRANKSHAFT

a.
A433310N01
1.375,1.313 1.531,1.51 0.156,0.198 10 false 1 0.677,0.302 0.833,0.5 0.156,0.198 10 true 4 1.75,0.281 1.948,0.448 0.198,0.167 10 true 10 1.229,0.302 1.385,0.458 0.156,0.156 10 true 8 0.667,1.896 0.823,2.094 0.156,0.198 10 true 3 1.219,1.885 1.375,2.083 0.156,0.198 10 true 7 1.802,1.896 1.958,2.094 0.156,0.198 10 true 9 2.354,1.885 2.51,2.083 0.156,0.198 10 true 5 2.917,1.896 3.073,2.063 0.156,0.167 10 true 1 2.917,0.313 3.073,0.49 0.156,0.177 10 true 2 2.354,0.313 2.531,0.469 0.177,0.156 10 true 6

Uniformly loosen and remove the 10 crankshaft bearing cap set bolts in several steps in the order shown in the illustration.


b.

Remove the 5 crankshaft bearing caps from the cylinder block sub-assembly.

HINT:
·

Keep the No. 2 crankshaft bearings and crankshaft bearing caps together.

·

Arrange the removed parts in such a way that they can be reinstalled to their original locations.




c.

Remove the crankshaft from the cylinder block sub-assembly.

HINT:

Keep the crankshaft bearings and crankshaft thrust washers together with the cylinder block sub-assembly.



d.

Check each crankshaft journal and crankshaft bearing for pitting and scratches.

If the journal or crankshaft bearing is damaged, replace the crankshaft bearings. If necessary, replace the crankshaft.


Hide 11791 9.REMOVE CRANKSHAFT THRUST WASHER

a.
A400506

Remove the 2 crankshaft thrust washers from the No. 3 journal position of the cylinder block sub-assembly.


Hide 10.REMOVE CRANKSHAFT BEARING

a.

Remove the 5 No. 1 crankshaft bearings and 5 No. 2 crankshaft bearings from the cylinder block sub-assembly and 5 crankshaft bearing caps.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 13011 11.REMOVE PISTON RING SET

a.
A400507C01
1.115,1.76 1.115,1.531 1.115,1.531 1.354,1.281 false 1.063,1.802 1.375,2 0.313,0.198 10 false *a
*a Piston Ring Expander


Using a piston ring expander, remove the No. 1 compression ring and No. 2 compression ring from the piston.


b.

Remove the oil ring expander, upper side rail and lower side rail from the piston by hand.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 13101A 12.REMOVE PISTON PIN HOLE SNAP RING

a.
A426847C01
1.885,0.979 2.208,1.188 true 2.104,0.813 2.313,0.375 true 2.25,1.115 2.563,1.271 0.313,0.156 10 false *a 2.344,0.271 2.656,0.427 0.313,0.156 10 false *b
*a Front Mark Cutout Portion
*b Protective Tape


Using a screwdriver, pry out the 2 piston pin hole snap rings from the piston.

HINT:

Tape the screwdriver tip before use.



Hide 13.REMOVE PISTON

a.
A400509

Gradually heat each piston to between 80 and 90°C (176 to 194°F).

CAUTION:

Be sure to wear protective gloves.



b.
A400510

Using a brass bar and a hammer, lightly tap out the piston pin and remove the connecting rod.

HINT:
·

The piston and piston pin are a matched set.

·

Arrange the removed parts in such a way that they can be reinstalled to their original locations.




Hide 15708 14.REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.
A426848

Using a 5 mm hexagon wrench, remove the 4 bolts and 4 No. 1 oil nozzle sub-assemblies from the cylinder block sub-assembly.


Hide 15709 15.REMOVE NO. 2 OIL NOZZLE SUB-ASSEMBLY

a.
A426849

Using a 5 mm hexagon wrench, remove the 4 bolts and 4 No. 2 oil nozzle sub-assemblies from the cylinder block sub-assembly.