Home › Power Source / Network › A25A-FXS (BATTERY / CHARGING) › CHARGING SYSTEM › from 2020.08
RM3620E _57 Power Source / Network _076184 A25A-FXS BATTERY / CHARGING _0372190 CHARGING SYSTEM G

A25A-FXS BATTERY / CHARGING  CHARGING SYSTEM  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced when inspecting auxiliary battery are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)

NOTICE:

After the power switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the power switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 1.CHECK AUXILIARY BATTERY

a.

Check that the auxiliary battery cables are connected to the correct terminals.

If they are not, connect them properly.


b.

Check the auxiliary battery for damage and deformation. If severe damage, deformation or leakage is found, replace the auxiliary battery.


Hide 2.CHECK AUXILIARY BATTERY VOLTAGE

a.

Turn the power switch off and turn on the high beam headlights for 30 seconds. This will remove the surface charge from the auxiliary battery.


b.

Measure the auxiliary battery voltage according to the value(s) in the table below.

Result:
Tester Connection Condition Specified Condition Result
Positive (+) auxiliary battery terminal - Negative (-) auxiliary battery terminal 20°C (68°F), Power switch off 12.0 V or higher Auxiliary battery is OK
12.0 V or less Recharge auxiliary battery



Hide 3.RECHARGE AUXILIARY BATTERY

a.

Recharge the auxiliary battery.

HINT:
·

Recharge the auxiliary battery according to the charger's instructions.

·

Apply the appropriate charging current according to the type of auxiliary battery shown in the table below.


Charge Method Charging Current
Normal Below 5 A
Quick Below 15 A



b.

Turn the power switch off and turn on the high beam headlights for 30 seconds. This will remove the surface charge from the auxiliary battery.


c.

Measure the auxiliary battery voltage according to the value(s) in the table below.

Result:
Tester Connection Condition Specified Condition Result
Positive (+) auxiliary battery terminal - Negative (-) auxiliary battery terminal 20°C (68°F), Power switch off 12.0 V or higher Auxiliary battery is OK
12.0 V or less Recharge auxiliary battery



Hide 4.CHECK AUXILIARY BATTERY TERMINAL, FUSIBLE LINK AND FUSE

a.

Check that the auxiliary battery terminals are not loose or corroded.

Torque:
Positive (+) Auxiliary Battery Terminal : 5.4 N*m (55 kgf*cm, 48 in.*lbf)
Negative (-) Auxiliary Battery Terminal : 5.4 N*m (55 kgf*cm, 48 in.*lbf)

If a terminal is loose or corroded, tighten or clean the terminal.


b.

Measure the resistance of each fusible link and fuse for the auxiliary battery charging system.

Standard resistance:

Below 1 Ω


If the result is not as specified, replace the fusible link or fuse as necessary.


Hide 5.CHECK AMD TERMINAL

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.




b.

Check that the AMD terminal is connected securely, and there is no contact problem.

If there are any arc marks, replace the affected parts.


c.
A432072C01
0.948,2.594 1.198,0.344 1.198,0.344 1.344,0.344 false 2.208,0.156 2.375,0.156 2.375,0.156 2.5,0.76 false 1.396,0.25 1.708,0.448 0.313,0.198 10 false *a 2.031,0.073 2.25,0.26 0.219,0.188 10 false *b
*a Inverter with Converter Assembly Side
*b No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly Side


Check that the nut for the AMD terminal is tightened to the specified torque.

Torque:
Inverter with Converter Assembly Side : 10 N*m (102 kgf*cm, 7 ft.*lbf)
No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly Side : 8.0 N*m (82 kgf*cm, 71 in.*lbf)

If there are no arc marks and the AMD terminal connection is faulty, connect the AMD terminal securely.



Hide 6.CHECK DC/DC CONVERTER FUNCTION

a.
A111747C13
0.802,0.979 1.146,0.646 1.146,0.646 1.281,0.646 false 1.177,1.26 0.896,1.656 0.896,1.656 0.75,1.656 false 1.302,0.563 1.49,0.719 0.188,0.156 10 *a 0.552,1.563 0.75,1.708 0.198,0.146 10 *b
*a Probe Direction
*b Current Flowing into Auxiliary Battery


Connect the AC/DC 400 A probe to the positive (+) auxiliary battery cable.


b.

Turn the power switch on (READY) and leave the vehicle as is until the electric current flowing to the auxiliary battery becomes 10 A or less.


c.

Turn on the high beam headlights, and turn the blower motor switch to the HI position and the rear window defogger on.


d.
A314451C01
0.729,0.854 0.865,0.417 0.865,0.417 1.083,0.417 false 0.719,1.76 0.938,1.76 0.938,1.76 1.229,1.313 false 1.135,0.333 1.448,0.49 0.313,0.156 10 false *a 0.563,1.688 0.875,1.844 0.313,0.156 10 false *b
*a Probe Direction
*b Current Flowing from Auxiliary Battery


Measure the current and voltage according to the value(s) in the table below.

Result:
Item Tester Connection Condition Specified Condition
Current flowing from auxiliary battery Positive (+) auxiliary battery cable Power switch on (READY)
(The high beam headlights are on, the blower motor switch is in the HI position, and the rear window defogger is turned on.)
0 A or less
(No current from auxiliary battery)
Auxiliary battery voltage Positive (+) auxiliary battery terminal - Negative (-) auxiliary battery terminal 12.5 to 15 V


If the result is not as specified, replace the inverter with converter assembly.