Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model) › from 2020.08
RM3620E _57 Power Source / Network _076016 NETWORKING _0371267 CAN COMMUNICATION SYSTEM(for Gasoline Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  Millimeter Wave Radar Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Millimeter Wave Radar Sensor Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Front Radar" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Front Radar" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Front Radar" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Millimeter Wave Radar Sensor Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Millimeter wave radar sensor assembly branch wire or connector

·

Power source circuit of millimeter wave radar sensor assembly

·

Millimeter wave radar sensor assembly ground circuit

·

Millimeter wave radar sensor assembly



WIRING DIAGRAM

C393549E07
5.604,0.5 6.219,0.698 0.615,0.198 10 false CA2H 5.615,1.156 6.229,1.354 0.615,0.198 10 false CA2L 5.604,3.458 6.219,3.656 0.615,0.198 10 false SGND 5.615,2.49 6.229,2.688 0.615,0.198 10 false IGB 3.365,2.75 4.49,2.969 1.125,0.219 10 false ECU IG1 NO.3*2 5.365,2.313 5.979,2.51 0.615,0.198 10 false 8 5.365,3.333 5.979,3.531 0.615,0.198 10 false 1 5.365,1.01 5.979,1.208 0.615,0.198 10 false 2 5.365,0.427 5.979,0.625 0.615,0.198 10 false 3 1.823,0.417 2.438,0.615 0.615,0.198 10 false 2 1.823,1.021 2.438,1.219 0.615,0.198 10 false 12 5.26,3.875 5.875,4.073 0.615,0.198 10 false B9 5.26,4.063 6.667,4.542 1.406,0.479 10 false Millimeter Wave Radar Sensor Assembly 0.323,1.406 2.656,1.688 2.333,0.281 10 false No. 2 CAN Junction Connector 0.313,1.229 0.927,1.427 0.615,0.198 10 false G102 1.573,2.979 3.302,3.396 1.729,0.417 10 false from IG1 NO.1 Relay*2 4.625,2.688 4.927,2.896 0.302,0.208 10 false *2 3.896,2.302 4.198,2.51 0.302,0.208 10 false *1 0.896,2.396 3.302,2.813 2.406,0.417 10 false from Engine Stop and Start ECU*1 0.146,3.646 2.615,3.885 2.469,0.24 10 false *1: w/ Engine Stop and Start System 0.125,4.01 2.594,4.25 2.469,0.24 10 false *2: w/o Engine Stop and Start System

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C346951C93
1.49,0.156 1.854,0.365 0.365,0.208 2.365,0.396 2.198,0.396 2.198,0.396 1.792,1.073 true 0.917,0.396 1.115,0.396 1.115,0.396 1.604,1.073 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.594,0.188 1.927,0.427 0.333,0.24 10 false B9 2.458,0.333 3.063,0.573 0.604,0.24 10 false CA2H 0.479,0.333 0.938,0.531 0.458,0.198 10 false CA2L
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the millimeter wave radar sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B9-3 (CA2H) - B9-2 (CA2L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result Proceed to
OK (w/ Stop and Start System) A
OK (w/o Stop and Start System) B
NG C



A

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

B

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

C

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C346951C94
1.49,0.156 1.854,0.365 0.365,0.208 2.49,2 2.313,2 2.313,2 1.979,1.344 true 0.917,0.396 1.115,0.396 1.115,0.396 1.406,1.073 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.583,0.188 1.917,0.458 0.333,0.271 10 false B9 2.542,1.938 2.969,2.146 0.427,0.208 10 false IGB 0.51,0.333 1.042,0.542 0.531,0.208 10 false SGND
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B9-1 (SGND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B9-8 (IGB) - Body ground Ignition switch ON 10.5 to 16 V
Ignition switch off Below 1 V



Result:
Result Proceed to
OK A
NG (IGB terminal) B
NG (Other terminal) C



A

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C346951C94
1.49,0.156 1.854,0.365 0.365,0.208 2.49,2 2.313,2 2.313,2 1.979,1.344 true 0.917,0.396 1.115,0.396 1.115,0.396 1.406,1.073 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.583,0.188 1.917,0.458 0.333,0.271 10 false B9 2.542,1.938 2.969,2.146 0.427,0.208 10 false IGB 0.51,0.333 1.042,0.542 0.531,0.208 10 false SGND
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B9-1 (SGND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B9-8 (IGB) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR