DTC P0136 Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2) |
DTC P0137 Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2) |
DTC P0138 Oxygen Sensor Circuit High Voltage (Bank 1 Sensor 2) |
DTC P0139 Oxygen Sensor Circuit Slow Response (Bank 1 Sensor 2) |
DTC P0156 Oxygen Sensor Circuit Malfunction (Bank 2 Sensor 2) |
DTC P0157 Oxygen Sensor Circuit Low Voltage (Bank 2 Sensor 2) |
DTC P0158 Oxygen Sensor Circuit High Voltage (Bank 2 Sensor 2) |
DTC P0159 Oxygen Sensor Circuit Slow Response (Bank 2 Sensor 2) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0136 P0156 |
|
|
| P0137 P0157 |
|
|
| P0138 P0158 |
|
|
| P0139 P0159 | The HO2 sensor voltage does not drop below 0.2 V immediately after fuel cut starts. |
|
| DTC No. | DTC Detection Condition | Trouble Area |
| P0136 P0156 | Not applicable | None |
| P0137 P0157 |
|
|
| P0138 P0158 | Not applicable | None |
| P0139 P0159 | Not applicable | None |



| Related DTCs | P0136: Heated oxygen sensor (for bank 1) output voltage (Abnormal voltage output) P0136: Heated oxygen sensor (for bank 1) impedance (Low) P0137: Heated oxygen sensor (for bank 1) output voltage (Low voltage) P0137: Heated oxygen sensor (for bank 1) impedance (High) P0138: Heated oxygen sensor (for bank 1) output voltage (High voltage) P0138: Heated oxygen sensor (for bank 1) output voltage (Extremely high) P0139: Heated oxygen sensor output voltage during fuel cut (for bank 1) P0156: Heated oxygen sensor (for bank 2) output voltage (Abnormal voltage output) P0156: Heated oxygen sensor (for bank 2) impedance (Low) P0157: Heated oxygen sensor (for bank 2) output voltage (Low voltage) P0157: Heated oxygen sensor (for bank 2) impedance (High) P0158: Heated oxygen sensor (for bank 2) output voltage (High voltage) P0158: Heated oxygen sensor (for bank 2) output voltage (Extremely high) P0159: Heated oxygen sensor output voltage during fuel cut (for bank 1) |
| Required Sensors/Components (Main) | Heated oxygen sensor |
| Required Sensors/Components (Related) | Crankshaft position sensor, engine coolant temperature sensor, mass air flow meter and throttle position sensor |
| Frequency of Operation | Once per driving cycle: Active air-fuel ratio control detection Continuous: Other |
| Duration | 20 seconds: Active air-fuel ratio control detection 90 seconds: Heated oxygen sensor impedance (High) 30 seconds: Heated oxygen sensor impedance (Low) 10 seconds: Output voltage (Stuck high) 9.3 seconds: Heated oxygen sensor voltage (during fuel cut) |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | P0016, P0018 (VVT System - Misalignment) P0031, P0032, P0051, P0052 (Air Fuel Ratio Sensor Heater) P0037, P0038, P0057, P0058 (Rear Oxygen Sensor Heater) P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256, P2A00, P2A03 (Air Fuel Ratio Sensor) P0102, P0103 (Mass Air Flow Sensor) P0110, P0112, P0113 (Intake Air Temperature Sensor) P0115, P0117, P0118 (Engine Coolant Temperature Sensor) P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle Position Sensor) P0128 (Thermostat) P0171, P0172, P0174, P0175 (Fuel System) P0300 - P0308 (Misfire) P0335 (Crankshaft Position Sensor) P1340 (Camshaft Position Sensor) P0412, P0415, P0418, P0419, P1613, P1614 (Secondary Air Injection System Control) P2440, P2441, P2442, P2443, P2444, P2445, P2446, P2447 (Secondary Air Injection System) P0500 (Vehicle Speed Sensor) |
| Active air-fuel ratio control | Executing |
| Active air-fuel ratio control begins when all of following conditions met: | - |
| Battery voltage | 11 V or more |
| Engine coolant temperature | 75°C (167°F) or more |
| Idling | OFF |
| Engine RPM | Less than 3200 rpm |
| A/F sensor status | Activated |
| Fuel system status | Closed loop |
| Fuel cut | OFF |
| Engine load | 10 to 70% |
| Shift position | 4th or higher |
| Battery voltage | 11 V or more |
| Estimated rear HO2 sensor temperature | Less than 700°C (1292°F) |
| DTC P0607 | Not set |
| Battery voltage | 11 V or more |
| Estimated rear HO2 sensor temperature | 450 to 750°C or more (842 to 1382°F) |
| ECM monitor | Completed |
| DTC P0607 | Not set |
| Battery voltage | 11 V or more |
| Time after engine start | 2 seconds or more |
| Engine coolant temperature | 75°C (167°F) or higher |
| Estimated catalyst temperature | 620°C (1148°F) or higher |
| Fuel cut | ON |
| Either of following conditions met: | 1 or 2 |
| 1. All of following conditions (a), (b) and (c) met | - |
| (a) Commanded air-fuel ratio | 14.3 or less |
| (b) Rear HO2 sensor voltage | 0.21 to 0.59 V |
| (c) OSC (Oxygen Storage Capacity of Catalyst) | 2 g or more |
| 2. All of following conditions (d), (e) and (f) met | - |
| (d) Commanded air-fuel ratio | 14.9 or more |
| (e) Rear HO2 sensor voltage | 0.21 to 0.59 V |
| (f) OSC | 2 g or more |
| All of following conditions (a), (b) and (c) met | - |
| (a) Commanded air-fuel ratio | 14.3 or less |
| (b) Rear HO2 sensor voltage | Less than 0.21 V |
| (c) OSC | 2 g or more |
| All of following conditions (a), (b) and (c) met | - |
| (a) Commanded air-fuel ratio | 14.9 or more |
| (b) Rear HO2 sensor voltage | More than 0.59 V |
| (c) OSC | 2 g or more |
| Duration of following condition met | 30 seconds or more |
| Heated oxygen sensor impedance | Less than 5 Ω |
| Duration of following condition met | 90 seconds or more |
| Heated oxygen sensor impedance | 15 kΩ or more |
| Duration of following condition met | 10 seconds or more |
| Heated oxygen sensor voltage | 1.2 V or more |
| Duration until rear heated oxygen sensor voltage drops to 0.2 V during fuel cut | 9.3 seconds or more |
| Duration of following condition met | 30 seconds or more |
| Heated oxygen sensor voltage | Varies between 0.1 and 0.9 V |


| Tester Display (Sensor) | Injection Volume | Status | Voltage |
| AFS Voltage B1 S1 or AFS Voltage B2 S1 (A/F) | +25% | Rich | Less than 3.1 V |
| AFS Voltage B1 S1 or AFS Voltage B2 S1 (A/F) | -12.5% | Lean | More than 3.4 V |
| O2S B1 S2 or O2S B2 S2 (HO2) | +25% | Rich | More than 0.55 V |
| O2S B1 S2 or O2S B2 S2 (HO2) | -12.5% | Lean | Less than 0.4 V |
| Case | A/F Sensor (Sensor 1) Output Voltage | HO2 Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area |
| 1 | ![]() ![]() | ![]() ![]() | - |
| 2 | ![]() ![]() | ![]() ![]() |
|
| 3 | ![]() ![]() | ![]() ![]() |
|
| 4 | ![]() ![]() | ![]() ![]() |
|
| 1.READ OUTPUT DTC (P0136, P0137, P0138, P0139, P0156, P0157, P0158 AND P0159) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream ON.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| P0138 or P0158 is output | A |
| P0137 or P0157 is output | B |
| P0136 or P0156 is output | C |
| P0139 or P0159 is output | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.READ VALUE USING TECHSTREAM (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream ON.
Enter the following menus: Powertrain / Engine / Data List / A/F Control System / O2S B1 S2 or O2S B2 S2.
Allow the engine to idle.
Read the Heated Oxygen (HO2) sensor output voltage while idling.
| Result | Proceed to |
| More than 1.0 V | A |
| Less than 1.0 V | B |
|
| ||||
| A | |
| 3.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT) |
![]() |
Disconnect the HO2 sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2 (+B) - 3 (OX1B) | Always | 10 kΩ or higher |
| 2 (+B) - 4 (E1) | Always | 10 kΩ or higher |
| 2 (+B) - 3 (OX2B) | Always | 10 kΩ or higher |
| 2 (+B) - 4 (E1) | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT) |
![]() |
Turn the ignition switch off and wait for 5 minutes.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D56-45 (HT1B) - D56-114 (OX1B) | Always | 10 kΩ or higher |
| D56-44 (HT2B) - D56-112 (OX2B) | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 5.CHECK AIR FUEL RATIO SENSOR |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream ON.
Clear DTC (Click here).
Drive the vehicle by the drive pattern as listed below:
Warm up the engine.
Drive the vehicle at 60 km/h (40 mph) or more for 10 minutes or more.
Stop the vehicle.
Accelerate the vehicle until 60 km/h (40 mph) or more and decelerate for 3 seconds or more. Perform this three times.

Enter the following menus: Powertrain / Engine / Monitor / O2 Sensor / Details.
Confirm that RANGE B1S1 is either PASS or FAIL.
Read the test value.
| Result | Proceed to |
| 3 mA or more | A |
| Less than 3 mA | B |
|
| ||||
| A | ||
| ||
| 6.READ VALUE USING TECHSTREAM (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream ON.
Start the engine.
Enter the following menus: Powertrain / Engine / Data List / A/F Control System / O2S B1 S2 or O2S B2 S2.
After warming up the engine, run the engine at an engine speed of 2500 rpm for 3 minutes.
Read the output voltage of the HO2 sensor when the engine rpm is suddenly increased.
|
| ||||
| OK | |
| 7.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136 OR P0156) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream ON.
Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.
Read DTCs.
| Result | Proceed to |
| P0136 or P0156 is output | A |
| No DTC is output | B |
|
| ||||
| A | |
| 9.REPLACE HEATED OXYGEN SENSOR |
Replace the heated oxygen sensor (Click here).
| NEXT | |
| 10.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 11.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136 OR P0156) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream ON.
Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.
Read DTCs.
| Result | Proceed to |
| P0136 or P0156 is output | A |
| No DTC is output | B |
|
| ||||
| A | |
| 12.PERFORM ACTIVE TEST USING TECHSTREAM (INJECTION VOLUME) |

Connect the Techstream to the DLC3.
Start the engine.
Turn the Techstream ON.
Warm up the engine.
Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume.
Change the fuel injection volume using the Techstream, and monitor the voltage output of Air-Fuel Ratio (A/F) and HO2 sensors displayed on the Techstream.
| Tester Display (Sensor) | Voltage Variation | Proceed to |
| AFS Voltage B1 S1 (A/F) AFS Voltage B2 S1 (A/F) | Alternates between more and less than 3.3 V | OK |
| Remains at more than 3.3 V | NG | |
| Remains at less than 3.3 V | NG |
|
| ||||
| OK | ||
| ||
| 13.CHECK FOR EXHAUST GAS LEAK |
|
| ||||
| OK | |
| 14.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the HO2 sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 (HT1B) - 2 (+B) | 20°C (68°F) | 11 to 16 Ω |
| 1 (HT1B) - 4 (E1) | Always | 10 kΩ or higher |
| 1 (HT2B) - 2 (+B) | 20°C (68°F) | 11 to 16 Ω |
| 1 (HT2B) - 4 (E1) | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 15.INSPECT INTEGRATION RELAY (EFI MAIN) |
![]() |
Remove the integration relay from the engine room relay block.
Inspect the EFI NO. 1 fuse.
Remove the EFI NO. 1 fuse from the integration relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| EFI NO. 1 fuse | Always | Below 1 Ω |
Reinstall the EFI NO. 1 fuse.
Inspect the EFI MAIN relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1C-1 - 1B-4 | When battery voltage not applied | 10 kΩ or higher |
| When battery voltage applied to terminals 1B-2 and 1B-3 | Below 1 Ω |
|
| ||||
| OK | |
| 16.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM) |
![]() ![]() |
Disconnect the HO2 sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D17-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| D18-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
Turn the ignition switch off.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D17-1 (HT1B) - D56-45 (HT1B) | Always | Below 1 Ω |
| D17-3 (OX1B) - D56-114 (OX1B) | Always | Below 1 Ω |
| D17-4 (E1) - D56-115 (EX1B) | Always | Below 1 Ω |
| D18-1 (HT2B) - D56-44 (HT2B) | Always | Below 1 Ω |
| D18-3 (OX2B) - D56-112 (OX2B) | Always | Below 1 Ω |
| D18-4 (E1) - D56-113 (EX2B) | Always | Below 1 Ω |
| D17-1 (HT1B) or D56-45 (HT1B) - Body ground | Always | 10 kΩ or higher |
| D17-3 (OX1B) or D56-114 (OX1B) - Body ground | Always | 10 kΩ or higher |
| D18-1 (HT2B) or D56-44 (HT2B) - Body ground | Always | 10 kΩ or higher |
| D18-3 (OX2B) or D56-112 (OX2B) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 17.READ VALUE USING TECHSTREAM (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR) |
Connect the Techstream to the DLC3.
Start the engine.
Turn the Techstream ON.
Enter the following menus: Powertrain / Engine / Data List/ A/F Control System / O2S B1 S2 or O2S B2 S2.
After warming up the engine, run the engine at an engine speed of 2500 rpm for 3 minutes.
Engine is Idling.
Depress the accelerator pedal quickly until the engine speed reaches 2500 rpm 3 times.
| Result | Proceed to |
| Higher than 1.0 V | A |
| Below 1.0 V | B |
|
| ||||
| A | |
| 18.INSPECT OXYGEN SENSOR |
![]() |
Disconnect the HO2 sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2 (+B) - 3 (OX1B) | Always | 10 kΩ or higher |
| 2 (+B) - 4 (E1) | Always | 10 kΩ or higher |
| 2 (+B) - 3 (OX2B) | Always | 10 kΩ or higher |
| 2 (+B) - 4 (E1) | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 19.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT) |
![]() |
Turn the ignition switch off and wait for 5 minutes.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Proceed to |
| D56-45 (HT1B) - D56-114 (OX1B) | 10 kΩ or higher |
| D56-44 (HT2B) - D56-112 (OX2B) | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 20.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 21.CHECK DTC OUTPUT (DTC P0139 OR P0159 OUTPUT AGAIN) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream ON.
Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.
Read the DTCs.
| Result | Proceed to |
| P0139 or P0159 | A |
| No output | B |
|
| ||||
| A | ||
| ||