Home › Engine / Hybrid System ยท 3UR-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P0300    Random / Multiple Cylinder Misfire Detected

DTC    P0301    Cylinder 1 Misfire Detected

DTC    P0302    Cylinder 2 Misfire Detected

DTC    P0303    Cylinder 3 Misfire Detected

DTC    P0304    Cylinder 4 Misfire Detected

DTC    P0305    Cylinder 5 Misfire Detected

DTC    P0306    Cylinder 6 Misfire Detected

DTC    P0307    Cylinder 7 Misfire Detected

DTC    P0308    Cylinder 8 Misfire Detected

for Preparation Click here


DESCRIPTION

A093767E03
When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high HC concentration levels can cause increases in exhaust emission levels. High concentrations of HC can also cause increases in the Three-Way Catalytic Converter (TWC) temperature, which may cause damage to the TWC. To prevent these increases in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire rate. When the temperature of the TWC reaches the point of thermal degradation, the MIL blinks. To monitor misfires, the ECM uses both the Camshaft Position (CMP) sensor and the Crankshaft Position (CKP) sensor. The CMP sensor is used to identify any misfiring cylinders and the CKP sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted as when the crankshaft rotation speed variations exceed predetermined thresholds.
If the misfire rate exceeds the threshold level, the ECM illuminates the MIL and stores a DTC.

DTC No.
DTC Detection Condition
Trouble Area
P0300
Simultaneous misfiring of several cylinders occurs and one of following conditions below is detected (2 trip detection logic):
  1. High temperature misfire occurs in Three-Way Catalytic Converter (TWC) (MIL blinks)
  2. Emission deterioration misfire occurs (MIL illuminates)
  1. Open or short in engine wire harness
  2. Connector connection
  3. Vacuum hose connections
  4. Ignition system
  5. Injector
  6. Fuel pressure
  7. Mass Air Flow (MAF) meter
  8. Engine Coolant Temperature (ECT) sensor
  9. Compression pressure
  10. Valve timing
  11. PCV valve and hose
  12. PCV hose connections
  13. Air induction system
  14. ECM
P0301
P0302
P0303
P0304
P0305
P0306
P0307
P0308
Misfiring of specific cylinder occurs and one of following conditions below is detected (2 trip detection logic):
  1. High temperature misfire occurs in Three-Way Catalytic Converter (TWC) (MIL blinks)
  2. Emission deterioration misfire occurs (MIL illuminates)
When multiple DTCs for misfiring cylinders are stored, but DTC P0300 is not stored, it indicates that misfires have been detected in different cylinders at different times. DTC P0300 is only stored when several misfiring cylinders are detected at the same time.

MONITOR DESCRIPTION

The ECM illuminates the MIL and stores a DTC when either one of the following conditions, which could cause emission deterioration, is detected (2 trip detection logic).
  1. Within the first 1000 crankshaft revolutions of the engine starting, an excessive misfiring rate (approximately 20 to 50 misfires per 1000 crankshaft revolutions) occurs once.
  2. An excessive misfiring rate (approximately 20 to 50 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.
The ECM flashes the MIL and stores a DTC when either one of the following conditions, which could cause the Three-Way Catalytic Converter (TWC) damage, is detected (2 trip detection logic).
  1. At a high engine rpm, a catalyst damage misfire, which monitored every 200 crankshaft revolutions, occurs once.
  2. At a normal engine rpm, a catalyst damage misfire, which monitored every 200 crankshaft revolutions, occurs 3 times.

HINT:
If a catalyst damage misfire occurs, the ECM informs the driver by flashing the MIL.

  1. Misfire Monitor for Mexico Models
    The ECM illuminates the MIL and sets a DTC when either one of the following conditions, which could cause emission deterioration, is detected (2 trip detection logic).
    1. Within the first 1000 crankshaft revolutions of the engine starting, an excessive misfiring rate (approximately 1000 misfires per 1000 crankshaft revolutions) occurs once.
    2. An excessive misfiring rate (approximately 500 misfires per 1,000 crankshaft revolutions) occurs a total of 4 times.
    The ECM flashes the MIL and sets a DTC when the following condition, which could cause the Three-Way Catalytic Converter (TWC) damage, is detected (2 trip detection logic).
    1. A catalyst damage misfire, which monitored every 200 crankshaft revolutions, occurs 3 times.

MONITOR STRATEGY


Related DTCs
P0300: Multiple cylinder misfire
P0301: Cylinder 1 misfire
P0302: Cylinder 2 misfire
P0303: Cylinder 3 misfire
P0304: Cylinder 4 misfire
P0305: Cylinder 5 misfire
P0306: Cylinder 6 misfire
P0307: Cylinder 7 misfire
P0308: Cylinder 8 misfire
Required Sensors/Components (Main)
Crankshaft position sensor and Camshaft position sensor
Required Sensors/Components (Related)
Engine coolant temperature and intake air temperature sensors and Mass air flow meter
Frequency of Operation
Continuous
Duration
1000 to 4000 crankshaft revolutions: Emission related misfire
200 to 600 crankshaft revolutions: Catalyst damaged misfire
MIL Operation
2 driving cycles: MIL illuminates when misfire detect
MIL flashes immediately: When catalyst damaged misfire occur
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Misfire 
Monitor runs whenever following DTCs not present
P0016, P0018 (VVT System - Misalignment)
P0017, P0019 (Exhaust VVT System - Misalignment)
P0102, P0103 (Mass air flow meter)
P0112, P0113 (Intake air temperature sensor)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0221, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0327, P0328, P0332, P0333, P032C, P032D, P033C, P033D (Knock sensor)
P0335 (Crankshaft position sensor)
P0340, P1340 (Camshaft position sensor)
P0351 - P0358 (Igniter)
P0500 (Vehicle speed sensor)
P0705 (Shift lever position switch)
Battery voltage
8 V or more
VVT system
Not operated by scan tool
Engine RPM
400 to 5900 rpm
Either of following conditions (a) or (b) met
-
(a) ECT at engine start
More than -7°C (19°F)
(b) ECT
More than 20°C (68°F)
Fuel cut
OFF

Monitor Period of Emission-Related-Misfire 
First 1000 revolutions after engine start, or Check Mode
Crankshaft 1000 revolutions
Except above
Crankshaft 1000 revolutions x 4

Monitor Period of Catalyst-Damaged-Misfire (MIL Blinks) 
All of following conditions 1, 2 and 3 met
Crankshaft 200 revolutions x 3
1. Driving cycles
1st
2. Check mode
OFF
3. Engine RPM
Less than 2800 rpm
Except above
Crankshaft 200 revolutions
  1. FOR MEXICO MODELS:

Misfire: for Mexico models 
Monitor runs whenever following DTCs not present
P0016, P0018 (VVT System - Misalignment)
P0017, P0019 (Exhaust VVT System - Misalignment)
P0102, P0103 (Mass air flow meter)
P0112, P0113 (Intake air temperature sensor)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0221, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0327, P0328, P0332, P0333, P032C, P032D, P033C, P033D (Knock sensor)
P0335 (Crankshaft position sensor)
P0340, P1340 (Camshaft position sensor)
P0351 - P0358 (Igniter)
P0500 (Vehicle speed sensor)
P0705 (Shift lever position switch)
Battery voltage
8 V or more
VVT system
Not operated by scan tool
Engine RPM
450 to 4500 rpm
ECT
More than 65°C (149°F)
Fuel cut
OFF

Monitor period of emission-related-misfire: for Mexico models 
First 1000 revolutions after engine start, or Check Mode
Crankshaft 1000 revolutions
Except above
Crankshaft 1000 revolutions x 4

Monitor period of catalyst-damaged-misfire (MIL blinks): for Mexico models 
All of following conditions 1, 2 and 3 met
Crankshaft 200 revolutions x 3
1. Driving cycles
1st
2. Check mode
OFF
Except above
Crankshaft 200 revolutions

TYPICAL MALFUNCTION THRESHOLDS


Monitor Period of Emission-Related-Misfire 
Misfire rate
1.5% or more

Monitor Period of Catalyst-Damaged-Misfire (MIL Blinks) 
Number of misfire per 200 revolutions
103 or more (varies with intake air amount and RPM)
  1. FOR MEXICO MODELS:

Monitor period of emission-related-misfire: for Mexico models 
Misfire rate
25 % or more: for 1st 1000 revolutions
12.5 % or more: after 1st 1000 revolutions

Monitor period of catalyst-damaged-misfire (MIL blinks): for Mexico models 
Number of misfire per 200 revolutions
103 or more (varies with intake air amount and RPM)
Paired cylinder misfire (MIL blinks immediately)
Detected

MONITOR RESULT

Refer to Checking Monitor Status (Click here).

WIRING DIAGRAM


A179943E01


A178647E02


A178648E02


CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the Techstream on.
  4. Record the DTC(s) and freeze frame data.
  5. Using the Techstream, switch the ECM from normal mode to check mode (Click here).
  6. Read the misfire counts of each cylinder (cylinder No. 1 to No. 8) with the engine in an idling condition. If any misfire count is displayed, skip the following confirmation driving pattern.
  7. Drive the vehicle several times with the conditions, such as engine rpm and engine load, shown in Misfire RPM and Misfire Load in the Data List.

    HINT:
    In order to store misfire DTCs, it is necessary to operate the vehicle for the period of time shown in the table below, with the Misfire RPM and Misfire Load in the Data List.

    Engine RPM
    Duration
    Idling
    3.5 minutes or more
    1000
    3 minutes or more
    2000
    1.5 minutes or more
    3000
    1 minute or more

  8. Check whether misfires have occurred by checking DTCs and freeze frame data.

    HINT:
    Do not turn the ignition switch off until the stored DTC(s) and freeze frame data have been recorded. When the ECM returns to normal mode (default), the stored DTC(s), freeze frame data and other data will be cleared.

  9. Record the DTC(s), freeze frame data and misfire counts.
  10. Turn the ignition switch off and wait for at least 5 seconds.

INSPECTION PROCEDURE

HINT:
  1. If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.
  2. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  3. If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the freeze frame data.
  4. If the misfire still cannot be reproduced even though the conditions stored in the freeze frame data have been duplicated, one of the following factors is considered to be a possible cause of the problem:
    1. The fuel level is low.
    2. Improper fuel is used.
    3. The spark plugs are dirty.
  5. After finishing repairs, check that no misfires occur in each cylinder (cylinder No. 1, No. 2, No. 3, No. 4, No. 5, No. 6, No. 7 and No. 8).
  6. Be sure to confirm that no misfiring cylinder DTCs are stored again by conducting the confirmation driving pattern, after the repairs.
  7. For 6 and 8 cylinder engines, the ECM intentionally does not stored the specific misfiring cylinder DTCs at high engine RPM. If misfires only occur during high engine RPM driving, only DTC P0300 is stored.
    In the event of DTC P0300 being present, perform the following operations:
    1. Clear the DTC (Click here).
    2. Start the engine and conduct the confirmation driving pattern.
    3. Read the misfiring rates of each cylinder or DTC(s) using the Techstream.
    4. Repair the cylinder(s) that has a high misfiring rate or is indicated by the DTC.
    5. After finishing repairs, conduct the confirmation driving pattern again, in order to verify that DTC P0300 is not stored.
  8. When either Short FT #1, Long FT #1, Short FT #2 or Long FT #2 in the freeze frame data is outside the range of +/-20%, the air-fuel ratio may be rich (-20% or less) or lean (+20% or more).
  9. When the Coolant Temp in the freeze frame data is less than 75°C (167°F), the misfires occurred only while warming up the engine.
  10. An extremely imbalanced drive wheel, which causes body vibration, may cause misfire DTCs detection.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE CODES)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 and/or P0308 are output
    A
    P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 and/or P0308 and other DTCs are output
    B

HINT:
If any DTCs other than P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 and P0308 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.READ VALUE USING TECHSTREAM (MISFIRE RPM AND MISFIRE LOAD)
  1. Connect the Techstream the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Misfire / Misfire RPM and Misfire Load.

  1. Read and note the Misfire RPM and Misfire Load values.

    HINT:
    The Misfire RPM and Misfire Load values indicate the vehicle conditions under which the misfire occurred.


NEXT


3.CHECK PCV HOSE CONNECTIONS
  1. Check the PCV hose connections.

    OK:
    PCV hose is connected correctly and is not damaged.



NG
REPAIR OR REPLACE PCV HOSE (Click here)
OK


4.READ VALUE USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Catalyst OT MF F/C.

  1. Read the value displayed on the Techstream.
    Result 
    Data List
    Tester Display
    Proceed to
    Catalyst OT MF F/C
    AVAIL (Avail)
    A
    NOT AVL (Not Avl)
    B



B
Go to step 6
A


5.PERFORM ACTIVE TEST USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Prohibit the Catalyst OT Misfire prevent F/C.

  1. Perform the Active Test.

    NOTICE:
    When performing the Active Test, make sure the vehicle is stopped and either idling or being revved within 3000 rpm.


NEXT


6.READ VALUE USING TECHSTREAM (MISFIRE COUNT)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Misfire / Cylinder #1 Misfire Rate, #2, #3, #4, #5, #6, #7 and #8.

  1. Allow the engine to idle.

  1. Read each value for CYL #1 to #8 (Cylinder #1 Misfire Rate to #8) displayed on the Techstream. If no misfire counts occur in any cylinders, perform the following procedures:

    1. Move the shift lever to D.

    2. Check the CYL #1 to #8 (Cylinder #1 Misfire Rate to #8).

    3. If misfire counts are still not displayed, perform procedure "A" and "B" and then check the misfire counts again.

  1. Drive the vehicle with the Misfire RPM and Misfire Load noted in the "Read value using Techstream (Misfire RPM and Misfire Load)" procedures above (Procedure "A").

  1. Read the CYL #1 to #8 (Cylinder #1 Misfire Rate to #8) or DTCs displayed on the Techstream (Procedure "B").
    Result 
    Result
    Proceed to
    Most misfires occur in only 1 or 2 cylinders
    A
    3 cylinders or more have equal misfire counts
    B

    HINT:
    1. If it is difficult to reproduce misfires for each cylinder, check the Data List item called Misfire Margin. Try to find vehicle driving conditions that lower the Misfire Margin value. Values above 30% are considered normal.
    2. If the freeze frame data's record of the ECT is below 75°C (167°F), the misfire may be detected only when the engine is cold.
    3. If the freeze frame data's record of the Engine Run Time is below 120 seconds, the misfire may be detected immediately after the engine is started.



B
Go to step 17
A


7.INSPECT SPARK PLUG
A126880E01
  1. Remove the ignition coil and the spark plug of the misfiring cylinder (Click here).

  1. Measure the spark plug electrode gap.

    Standard gap:
    1.0 to 1.1 mm (0.0394 to 0.0433 in.)

  1. Check the electrode for carbon deposits.
    Recommended Spark Plug 
    Manufacturer
    Product
    DENSO
    SK20HR11

    NOTICE:
    If the electrode gap is larger than standard, replace the spark plug. Do not adjust the electrode gap.



NG
REPLACE SPARK PLUG (Click here)
OK


8.CHECK FOR SPARKS AND IGNITION
A151834
  1. Disconnect the injector connectors to prevent the engine from starting.

    CAUTION:
    Always disconnect all injector connectors.

    NOTICE:
    Do not crank the engine for more than 2 seconds.

  1. Remove the ignition coil from the cylinder head (Click here).

  1. Install the spark plug onto the ignition coil.

  1. Attach the spark plug assembly to the cylinder head.

  1. Crank the engine for less than 2 seconds and check the spark.

    OK:
    Sparks jump across electrode gap.

  1. Install the ignition coil.

  1. Reconnect the injector connectors.



NG
Go to step 27
OK


9.CHECK CYLINDER COMPRESSION PRESSURE
  1. Measure the cylinder compression pressure of the misfiring cylinder .



NG
REPAIR ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


10.INSPECT ECM TERMINAL OF MISFIRING CYLINDER (#10, #20, #30, #40, #50, #60, #70 AND/OR #80 VOLTAGE)
A136305E59
  1. Disconnect the ECM connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D56-86 (#10) - D56-43 (E01)
    Ignition switch ON
    11 to 14 V
    D56-109 (#20) - D56-43 (E01)
    Ignition switch ON
    11 to 14 V
    D56-85 (#30) - D56-43 (E01)
    Ignition switch ON
    11 to 14 V
    D56-108 (#40) - D56-43 (E01)
    Ignition switch ON
    11 to 14 V
    D56-84 (#50) - D56-43 (E01)
    Ignition switch ON
    11 to 14 V
    D56-107 (#60) - D56-43 (E01)
    Ignition switch ON
    11 to 14 V
    D56-83 (#70) - D56-43 (E01)
    Ignition switch ON
    11 to 14 V
    D56-106 (#80) - D56-43 (E01)
    Ignition switch ON
    11 to 14 V



NG
GO TO FUEL INJECTOR CIRCUIT (Click here)
OK


11.CHECK FUEL INJECTOR OF MISFIRING CYLINDER
  1. Check the injector injection [whether fuel volume is high or low, and whether injection pattern is poor] (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


12.CHECK AIR INDUCTION SYSTEM
  1. Check the air induction system for vacuum leakage .

    OK:
    No leakage from air induction system.



NG
REPAIR OR REPLACE AIR INDUCTION SYSTEM
OK


13.CHECK VALVE TIMING

A166451E03

  1. Remove the cylinder head cover LH and RH.

  1. Turn the crankshaft pulley, and align its groove with the alignment mark "0" of the timing chain cover.

  1. Check that the alignment marks of the camshaft timing gears and camshaft timing exhaust gears are at the positions shown in the illustration.

    OK:
    Alignment marks on camshaft timing gears are aligned as shown in the illustration.



NG
ADJUST VALVE TIMING (Click here)
OK


14.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
CHECK AND REPLACE FUEL PUMP, PRESSURE REGULATOR, FUEL PIPE LINE AND FILTER
OK


15.READ VALUE USING TECHSTREAM (COOLANT TEMP)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.

  1. Read the Coolant Temp twice, when the engine is both cold and warmed up.

    Standard:
    With cold engine: Same as ambient air temperature.
    With warm engine: Between 75°C and 100°C (167°F and 212°F).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


16.READ VALUE USING TECHSTREAM (MAF)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF and Coolant Temp.

  1. Allow the engine to idle until the Coolant Temp reaches 75°C (167°F) or more.

  1. Read the MAF with the engine in an idling condition.

    Standard:
    MAF while engine idling: Between 4 g/sec. and 8 g/sec. (shift lever: N; A/C: OFF).



NG
REPLACE MASS AIR FLOW METER (Click here)
OK

REPLACE ECM (Click here)  

17.CHECK AIR INDUCTION SYSTEM
  1. Check the air induction system for vacuum leakage .

    OK:
    No leakage from air induction system.



NG
REPAIR OR REPLACE AIR INDUCTION SYSTEM (Click here)
OK


18.CHECK VALVE TIMING

A166451E03

  1. Remove the cylinder head cover LH and RH.

  1. Turn the crankshaft pulley, and align its groove with the alignment mark "0" of the timing chain cover.

  1. Check that the alignment marks of the camshaft timing gears and camshaft timing exhaust gears are at the positions shown in the illustration.

    OK:
    Alignment marks on camshaft timing gears are aligned as shown in the illustration.



NG
ADJUST VALVE TIMING (Click here)
OK


19.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
CHECK AND REPLACE FUEL PUMP, PRESSURE REGULATOR, FUEL PIPE LINE AND FILTER
OK


20.READ VALUE USING TECHSTREAM (COOLANT TEMP)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.

  1. Read the Coolant Temp twice, when the engine is both cold and warmed up.

    Standard:
    With cold engine: Same as ambient air temperature.
    With warm engine: Between 75°C and 100°C (167°F and 212°F).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


21.READ VALUE USING TECHSTREAM (MAF)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF and Coolant Temp.

  1. Allow the engine to idle until the Coolant Temp reaches 75°C (167°F) or more.

  1. Read the MAF with the engine in an idling condition.

    Standard:
    MAF while engine idling: Between 4 g/sec. and 8 g/sec. (shift lever: N; A/C: OFF).



NG
REPLACE MASS AIR FLOW METER (Click here)
OK


22.INSPECT SPARK PLUG
A126880E01
  1. Remove the ignition coil and the spark plug of the misfiring cylinder (Click here).

  1. Measure the spark plug electrode gap.

    Standard gap:
    1.0 to 1.1 mm (0.0394 to 0.0433 in.)

  1. Check the electrode for carbon deposits.
    Recommended Spark Plug 
    Manufacturer
    Product
    DENSO
    SK20HR11

    NOTICE:
    If the electrode gap is larger than standard, replace the spark plug. Do not adjust the electrode gap.



NG
REPLACE SPARK PLUG (Click here)
OK


23.CHECK FOR SPARKS AND IGNITION
A151834
  1. Disconnect the injector connectors to prevent the engine from starting.

    CAUTION:
    Always disconnect all injector connectors.

    NOTICE:
    Do not crank the engine for more than 2 seconds.

  1. Remove the ignition coil from the cylinder head (Click here).

  1. Install the spark plug onto the ignition coil.

  1. Attach the spark plug assembly to the cylinder head.

  1. Crank the engine for less than 2 seconds and check the spark.

    OK:
    Sparks jump across electrode gap.

  1. Install the ignition coil.

  1. Reconnect the injector connectors.



NG
Go to step 27
OK


24.CHECK CYLINDER COMPRESSION PRESSURE
  1. Measure the cylinder compression pressure of the misfiring cylinder .



NG
REPAIR ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


25.INSPECT ECM TERMINAL OF MISFIRING CYLINDER (#10, #20, #30, #40, #50, #60, #70 AND/OR #80 VOLTAGE)
A136305E59
  1. Disconnect the ECM connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D56-86 (#10) - D56-43 (E01)
    Ignition switch ON
    11 to 14 V
    D56-109 (#20) - D56-43 (E01)
    Ignition switch ON
    11 to 14 V
    D56-85 (#30) - D56-43 (E01)
    Ignition switch ON
    11 to 14 V
    D56-108 (#40) - D56-43 (E01)
    Ignition switch ON
    11 to 14 V
    D56-84 (#50) - D56-43 (E01)
    Ignition switch ON
    11 to 14 V
    D56-107 (#60) - D56-43 (E01)
    Ignition switch ON
    11 to 14 V
    D56-83 (#70) - D56-43 (E01)
    Ignition switch ON
    11 to 14 V
    D56-106 (#80) - D56-43 (E01)
    Ignition switch ON
    11 to 14 V



NG
GO TO FUEL INJECTOR CIRCUIT (Click here)
OK


26.CHECK FUEL INJECTOR OF MISFIRING CYLINDER
  1. Check the injector injection [whether fuel volume is high or low, and whether injection pattern is poor] (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK

REPLACE ECM (Click here)  

27.CHANGE TO NORMAL SPARK PLUG AND CHECK SPARK OF MISFIRING CYLINDER
  1. Change the installed spark plug to a spark plug that functions normally.

  1. Perform a spark test.

    CAUTION:
    Always disconnect all injector connectors.

    NOTICE:
    Do not crank the engine for more than 2 seconds.

    1. Install the spark plug to the ignition coil and connect the ignition coil connector.

    2. Disconnect the injector connector.

    3. Ground the spark plug.

    4. Check if sparks occur while the engine is being cranked.

      OK:
      Sparks jump across electrode gap.



NG
Go to step 28
OK

REPLACE SPARK PLUG (Click here)  

28.CHANGE TO NORMAL IGNITION COIL AND CHECK SPARK OF MISFIRING CYLINDER
  1. Change the ignition coil to an ignition coil that functions normally.

  1. Perform a spark test.

    CAUTION:
    Always disconnect all injector connectors.

    NOTICE:
    Do not crank the engine for more than 2 seconds.

    1. Install the spark plug to the ignition coil and connect the ignition coil connector.

    2. Disconnect the injector connector.

    3. Ground the spark plug.

    4. Check if sparks occur while the engine is being cranked.

      OK:
      Sparks jump across electrode gap.



NG
REPLACE ECM (Click here)
OK

REPLACE IGNITION COIL (Click here)