DTC P0351 Ignition Coil "A" Primary / Secondary Circuit |
DTC P0352 Ignition Coil "B" Primary / Secondary Circuit |
DTC P0353 Ignition Coil "C" Primary / Secondary Circuit |
DTC P0354 Ignition Coil "D" Primary / Secondary Circuit |
DTC P0355 Ignition Coil "E" Primary / Secondary Circuit |
DTC P0356 Ignition Coil "F" Primary / Secondary Circuit |
DTC P0357 Ignition Coil "G" Primary / Secondary Circuit |
DTC P0358 Ignition Coil "H" Primary / Secondary Circuit |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0351 P0352 P0353 P0354 P0355 P0356 P0357 P0358 | No IGF signal to ECM while engine running (1 trip detection logic) |
|

| Item | Content |
| Terminal | CH1: IGT1, IGT2, IGT3, IGT4, IGT5, IGT6, IGT7, IGT8 - E1 CH2: IGF1, IGF2 - E1 |
| Equipment Setting | 2 V/DIV. 20 msec./DIV. |
| Condition | Cranking or idling |

| Related DTCs | P0351: Igniter (cylinder 1) malfunction P0352: Igniter (cylinder 2) malfunction P0353: Igniter (cylinder 3) malfunction P0354: Igniter (cylinder 4) malfunction P0355: Igniter (cylinder 5) malfunction P0356: Igniter (cylinder 6) malfunction P0357: Igniter (cylinder 7) malfunction P0358: Igniter (cylinder 8) malfunction |
| Required Sensors/Components (Main) | Igniter |
| Required Sensors/Components (Related) | Crankshaft position sensor |
| Frequency of Operation | Continuous |
| Duration | About 1 second |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | None |
| Either of following conditions A or B met | - |
| A. Engine RPM | 1500 rpm or less |
| B. Starter | OFF |
| Either of following conditions C or D met | - |
| C. Both of following conditions (a) and (b) met | - |
| (a) Engine speed | 500 rpm or less |
| (b) Battery voltage | 6 V or more |
| D. All of following conditions (a), (b) and (c) met | - |
| (a) Engine speed | More than 500 rpm |
| (b) Battery voltage | 10 V or more |
| (c) Number of sparks after CPU reset | 5 sparks or more |
| IGF signal | ECM does not receive any IGF signal despite ECM sending IGT signal to igniter |
| IGF signal | Igniter transmits IGF signal when it receives IGT signal from ECM |


| 1.INSPECT IGNITION COIL ASSEMBLY (POWER SOURCE) |
![]() |
Disconnect the ignition coil with igniter connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D5-4 (GND) - Body ground | Always | Below 1 Ω |
| D13-4 (GND) - Body ground | Always | Below 1 Ω |
| D6-4 (GND) - Body ground | Always | Below 1 Ω |
| D12-4 (GND) - Body ground | Always | Below 1 Ω |
| D7-4 (GND) - Body ground | Always | Below 1 Ω |
| D11-4 (GND) - Body ground | Always | Below 1 Ω |
| D8-4 (GND) - Body ground | Always | Below 1 Ω |
| D10-4 (GND) - Body ground | Always | Below 1 Ω |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D5-1 (+B) - D5-4 (GND) | Ignition switch ON | 11 to 14 V |
| D13-1 (+B) - D13-4 (GND) | Ignition switch ON | 11 to 14 V |
| D6-1 (+B) - D6-4 (GND) | Ignition switch ON | 11 to 14 V |
| D12-1 (+B) - D12-4 (GND) | Ignition switch ON | 11 to 14 V |
| D7-1 (+B) - D7-4 (GND) | Ignition switch ON | 11 to 14 V |
| D11-1 (+B) - D11-4 (GND) | Ignition switch ON | 11 to 14 V |
| D8-1 (+B) - D8-4 (GND) | Ignition switch ON | 11 to 14 V |
| D10-1 (+B) - D10-4 (GND) | Ignition switch ON | 11 to 14 V |
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM) |
![]() |
Disconnect the ignition coil with igniter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D5-2 (IGF1) - D56-104 (IGF1) | Always | Below 1 Ω |
| D13-2 (IGF2) - D56-105 (IGF2) | Always | Below 1 Ω |
| D6-2 (IGF2) - D56-105 (IGF2) | Always | Below 1 Ω |
| D12-2 (IGF1) - D56-104 (IGF1) | Always | Below 1 Ω |
| D7-2 (IGF2) - D56-105 (IGF2) | Always | Below 1 Ω |
| D11-2 (IGF1) - D56-104 (IGF1) | Always | Below 1 Ω |
| D8-2 (IGF1) - D56-104 (IGF1) | Always | Below 1 Ω |
| D10-2 (IGF2) - D56-105 (IGF2) | Always | Below 1 Ω |
| D5-3 (IGT1) - D56-40 (IGT1) | Always | Below 1 Ω |
| D13-3 (IGT2) - D56-33 (IGT2) | Always | Below 1 Ω |
| D6-3 (IGT3) - D56-37 (IGT3) | Always | Below 1 Ω |
| D12-3 (IGT4) - D56-38 (IGT4) | Always | Below 1 Ω |
| D7-3 (IGT5) - D56-35 (IGT5) | Always | Below 1 Ω |
| D11-3 (IGT6) - D56-36 (IGT6) | Always | Below 1 Ω |
| D8-3 (IGT7) - D56-34 (IGT7) | Always | Below 1 Ω |
| D10-3 (IGT8) - D56-39 (IGT8) | Always | Below 1 Ω |
| D5-2 (IGF1) or D56-104 (IGF1) - Body ground | Always | 10 kΩ or higher |
| D13-2 (IGF2) or D56-105 (IGF2) - Body ground | Always | 10 kΩ or higher |
| D6-2 (IGF2) or D56-105 (IGF2) - Body ground | Always | 10 kΩ or higher |
| D12-2 (IGF1) or D56-104 (IGF1) - Body ground | Always | 10 kΩ or higher |
| D7-2 (IGF2) or D56-105 (IGF2) - Body ground | Always | 10 kΩ or higher |
| D11-2 (IGF1) or D56-104 (IGF1) - Body ground | Always | 10 kΩ or higher |
| D8-2 (IGF1) or D56-104 (IGF1) - Body ground | Always | 10 kΩ or higher |
| D10-2 (IGF2) or D56-105 (IGF2) - Body ground | Always | 10 kΩ or higher |
| D5-3 (IGT1) or D56-40 (IGT1) - Body ground | Always | 10 kΩ or higher |
| D13-3 (IGT2) or D56-33 (IGT2) - Body ground | Always | 10 kΩ or higher |
| D6-3 (IGT3) or D56-37 (IGT3) - Body ground | Always | 10 kΩ or higher |
| D12-3 (IGT4) or D56-38 (IGT4) - Body ground | Always | 10 kΩ or higher |
| D7-3 (IGT5) or D56-35 (IGT5) - Body ground | Always | 10 kΩ or higher |
| D11-3 (IGT6) or D56-36 (IGT6) - Body ground | Always | 10 kΩ or higher |
| D8-3 (IGT7) or D56-34 (IGT7) - Body ground | Always | 10 kΩ or higher |
| D10-3 (IGT8) or D56-39 (IGT8) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353, P0354, P0355, P0356, P0357 OR P0358) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream ON.
Clear DTCs (Click here).
Shuffle arrangement of the ignition coils with igniters (among No. 1 to No. 8 cylinders).
Perform a simulation test.
Check DTCs displayed on the Techstream.
| Result | Proceed to |
| Same DTC is output | A |
| Different ignition coil DTC is output | B |
|
| ||||
| A | ||
| ||