Home › Engine / Hybrid System ยท 2UZ-FE › ENGINE MECHANICAL › ENGINE ASSEMBLY

ENGINE ASSEMBLY > REMOVAL

for Preparation Click here



1. DISCHARGE FUEL SYSTEM PRESSURE
(Click here)


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some system need to be initialized after the cable is reconnected (Click here).



3. REMOVE NO. 1 ENGINE UNDER COVER


    A150108
  1. Remove the 3 screws and 5 bolts.

  1. Unhook the engine under cover from the vehicle body as shown in the illustration.



4. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug and 2 cylinder block drain cock plugs.

  1. Remove the radiator cap. Then drain the coolant.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.



  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 10 ft.*lbf }



    A156211E01

  1. Tighten the radiator drain cock plug by hand.



5. DRAIN ENGINE OIL


    A150107
  1. Remove the oil filler cap.

  1. Remove the oil drain plug and gasket, and drain the engine oil into a container.

  1. Install a new gasket and the oil pan drain plug.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



6. REMOVE HOOD SUB-ASSEMBLY


    A160839
  1. Using a screwdriver, remove the hood support assembly while releasing the 2 clips.

    HINT:
    Tape the screwdriver tip before use.

    CAUTION:
    Remove the hood support assembly while supporting the hood by hand.

  1. Remove the 4 bolts and hood.



7. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH


    E161312
  1. Remove the nut and remove the wiper arm and blade assembly.



8. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

HINT:
Use the same procedure for both sides.



9. REMOVE FRONT FENDER TO COWL SIDE SEAL LH

HINT:
Use the same procedure for both sides.



10. REMOVE FRONT FENDER TO COWL SIDE SEAL RH


    E161313
  1. Disengage the claw and remove the front fender to cowl side seal.



11. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    E161315
  1. Remove the 2 clips.

  1. Remove the 6 claws and 8 guides and remove the cowl top ventilator louver sub-assembly.



12. REMOVE FRONT WIPER MOTOR AND LINK ASSEMBLY


    E161316
  1. Disconnect the connector.

  1. Remove the nut.

  1. Remove the 4 bolts and wiper motor and link assembly.



13. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY
  1. Disconnect the washer hose.

  1. Separate the washer hose grommet from the front cowl top outer panel sub-assembly.

  1. Separate the wire harness clamp from the front cowl top outer panel sub-assembly.



  1. Remove the 7 bolts and front cowl top outer panel sub-assembly.


    A151796



14. REMOVE THROTTLE BODY COVER SUB-ASSEMBLY


    A153486
  1. Remove the 2 nuts and throttle body cover sub-assembly.



15. REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE


A185295
  1. Disconnect the air flow meter connector.

  1. Separate the wire harness.

  1. Disconnect the vacuum hose and No. 2 ventilation hose.

  1. Loosen the air cleaner hose clamp.

  1. Remove the 2 bolts and air cleaner with air cleaner hose assembly.



16. REMOVE RADIATOR ASSEMBLY
  1. Remove the radiator assembly (Click here).



17. REMOVE EFI FUEL PIPE CLAMP


A185283
  1. Remove the fuel pipe clamp.



18. DISCONNECT NO. 2 FUEL PIPE SUB-ASSEMBLY


A185284E01
  1. Pinch the retainer as illustrated, and then pull the fuel tube connector out of the pipe.

    NOTICE:
    1. Remove any dirt and foreign matter from the fuel tube connector before performing this work.
    2. Do not allow any scratches or foreign matter onto the parts when disconnecting, as the fuel tube connector has the O-rings that seals the pipe.
    3. Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the disconnected part by covering it with a vinyl bag after disconnecting the fuel tube.
    6. If the fuel tube connector and pipe are stuck, push and pull to release them.



19. DISCONNECT NO. 1 FUEL PIPE SUB-ASSEMBLY


A185285E01
  1. Pinch the retainer as illustrated, and then pull the fuel tube connector out of the pipe.

    NOTICE:
    1. Remove any dirt and foreign matter from the fuel tube connector before performing this work.
    2. Do not allow any scratches or foreign matter onto the parts when disconnecting, as the fuel tube connector has the O-rings that seals the pipe.
    3. Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the disconnected part by covering it with a vinyl bag after disconnecting the fuel tube.
    6. If the fuel tube connector and pipe are stuck, push and pull to release them.



20. DISCONNECT VACUUM HOSE ASSEMBLY


    A156175
  1. Remove the bolt and disconnect the vacuum hose assembly.



21. DISCONNECT INLET HEATER WATER HOSE B


A185289
  1. Disconnect the inlet heater water hose B.



22. DISCONNECT OUTLET HEATER WATER HOSE B


A185303
  1. Disconnect the outlet heater water hose B.



23. DISCONNECT OUTLET HEATER WATER HOSE C


A185287
  1. Disconnect the outlet heater water hose C.



24. DISCONNECT INLET HEATER WATER HOSE C


A185288
  1. Disconnect the inlet heater water hose C.



25. DISCONNECT NO. 2 AIR INJECTION SYSTEM HOSE


A185294
  1. Disconnect the No. 2 air injection system hose.



26. SEPARATE ENGINE WIRE


A185290
  1. Disconnect the clamp and ECM connector.



    A185292
  1. Disconnect the 5 connectors.



    A185297
  1. Disconnect the air pump connector and remove the bolt and connector bracket.



    A185296
  1. Remove the bolt and disconnect the ground wire.



    A160786E01
  1. Remove the nut and disconnect the wire from the positive (+) battery terminal.

  1. Disconnect the positive (+) battery terminal.

  1. Remove the bolt and disconnect the ground wire.

  1. Disconnect the 4 air injection control driver connectors.

  1. Remove the nut and disconnect the wire from the engine room junction block.

  1. Disconnect the 3 connectors from the engine room junction block.



27. SEPARATE COOLER COMPRESSOR ASSEMBLY


    A160758
  1. Disconnect the connector.

  1. Remove the 3 bolts, nut and No. 1 compressor stay and separate the cooler compressor.



28. SEPARATE VANE PUMP ASSEMBLY
  1. Disconnect the connector.

  1. Remove the 2 bolts and separate vane pump assembly.

    HINT:
    Hang up the hoses instead of detaching them.



29. REMOVE GENERATOR ASSEMBLY


    A152261
  1. Disconnect the generator assembly connector.

  1. Remove the terminal cap and nut, and disconnect the generator wire.

  1. Remove the bolt and disconnect the wire harness bracket from the generator assembly.



    A152262
  1. Remove the bolt, 2 nuts and generator assembly.



30. REMOVE NO. 1 WATER BY-PASS PIPE


    A160801
  1. Remove the 2 bolts and water by-pass pipe.



31. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY (for 2WD)
  1. Remove the automatic transmission assembly (Click here).



32. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY (for 4WD)
  1. Remove the automatic transmission assembly (Click here).



33. REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY


    A160799E01
  1. Using SST, hold the crankshaft.

    SST
    09213-70011  
    09330-00021  



    A160778
  1. Remove the 8 bolts, front drive plate spacer, drive plate and rear drive plate spacer.



34. REMOVE OIL COOLER TUBE


    C157296
  1. Remove the 2 bolts and oil cooler tube.



35. REMOVE ENGINE ASSEMBLY


    A160773E02
  1. Attach an engine sling device and hang the engine with a chain block.

  1. Remove the 4 engine mounting insulator bolts.

  1. Lift the engine out from the vehicle slowly and carefully.

    NOTICE:
    Make sure the engine is clear of all wiring, hoses and cables.



36. REMOVE NO. 3 AIR TUBE


A153518
  1. Remove the 4 nuts, No. 3 air tube and 2 gaskets.

    NOTICE:
    Be careful not to damage the installation surface of the gaskets.



37. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR


    A156202E02
  1. Remove the 4 bolts and No. 2 exhaust manifold heat insulator.



38. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH


    A156204E02
  1. Remove the 8 nuts and exhaust manifold sub-assembly LH.



    A162072E01
  1. Remove the gasket.



39. REMOVE NO. 3 AIR INJECTION SYSTEM HOSE


    A153510
  1. Disconnect the air switching valve assembly connector.

  1. Disconnect the wire harness clamp.



    A153512
  1. Remove the 4 nuts, No. 2 air tube and 2 gaskets.

    NOTICE:
    Be careful not to damage the installation surface of the gaskets.



40. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE


    A150112E01
  1. Remove the dipstick.

  1. Remove the bolt and dipstick guide.

  1. Remove the O-ring from the dipstick guide.



41. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR


    A156201E02
  1. Remove the 4 bolts and No. 1 exhaust manifold heat insulator.



42. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH


    A156203E03
  1. Remove the 8 nuts and exhaust manifold sub-assembly RH.



    A162071E01
  1. Remove the gasket.



43. INSTALL ENGINE ON ENGINE STAND
  1. Install the engine onto an engine stand with the bolts.