Home › Power Source / Network · NETWORKING › CAN COMMUNICATION SYSTEM

DTC    U1002    Lost Communication with Gateway Module

for Preparation Click here


DESCRIPTION

If 2 or more DTCs are output during the DTC check, one side of the CAN branch wire may be open. (One side of the CANH [branch wire]/CANL [branch wire] of the ECU and/or sensor is open.)

DTC Code
DTC Detection Condition
Trouble Area
U1002
Main body ECU cannot receive signals from all ECUs that have been memorized as those connected to the CAN MS bus.
  1. MS bus circuit
  2. Power seat control ECU branch wire or connector
  3. Multiplex tilt and telescopic ECU branch wire or connector
  4. Outer mirror control ECU branch wire or connector
  5. Power back door ECU branch wire or connector*1
  6. Combination meter ECU main wire or connector
  7. Main body ECU main wire or connector
  8. Power seat control ECU
  9. Multiplex tilt and telescopic ECU
  10. Outer mirror control ECU
  11. Combination meter ECU
  12. Main body ECU
  13. Power back door ECU*1
  14. No. 3 junction connector
  15. No. 4 junction connector*1

HINT:
*1: w/ Power back door system


WIRING DIAGRAM


E158720E01


INSPECTION PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NEXT


2.CHECK CAN BUS WIRE (MAIN WIRE FOR DISCONNECTION, BUS LINES FOR SHORT CIRCUIT)


    C191512E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    Resistance of Malfunction
    H37-22 (CANH) - H37-21 (CANL)
    Ignition switch off
    54 to 69 Ω
    Below 53 Ω: Short in line
    70 Ω or higher: Open in CAN main bus line
    H37-22 (CANH) - H37-18 (B)
    Ignition switch off
    6 kΩ higher
    Below 6 kΩ: +B short
    H37-21 (CANL) - H37-18 (B)
    H37-22 (CANH) - H37-40 (E1)
    Ignition switch off
    200 Ω or higher
    Below 200 Ω: Ground short
    H37-21 (CANL) - H37-40 (E1)

    Result 
    Result
    Proceed to
    NG
    - Open in CAN main wire
    A
    NG (w/ Power back door system)
    - Short in line
    - +B short
    - Ground short
    B
    NG (w/o Power back door system)
    - Short in line
    - +B short
    - Ground short
    C
    OK
    D



B
Go to step 15

C
Go to step 26

D
Go to step 45
A


3.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)


    C137766E78
  1. with Power back door system:

    1. Disconnect the H104 No. 3 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      H104-1 (CANH) - H104-2 (CANL)
      Ignition switch off
      108 to 132 Ω



    C137766E78
  1. without Power back door system:

    1. Disconnect the H104 No. 3 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      H104-1 (CANH) - H104-2 (CANL)
      Ignition switch off
      108 to 132 Ω

      Result 
      Result
      Proceed to
      OK
      A
      NG (w/o Power back door system)
      B
      NG (w/ Power back door system)
      C



B
Go to step 8

C
Go to step 10
A


4.CONNECT CONNECTOR
  1. Reconnect the H104 No. 3 junction connector.


NEXT


5.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - COMBINATION METER ECU)


    C137766E79
  1. Disconnect the H102 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H102-1 (CANH) - H102-2 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 6
OK

REPAIR OR REPLACE NO. 3 JUNCTION CONNECTOR 

6.CONNECT CONNECTOR
  1. Reconnect the H102 No. 3 junction connector.


NEXT


7.CHECK FOR OPEN IN CAN BUS WIRE (COMBINATION METER ECU - NO. 3 JUNCTION CONNECTOR)


    C159487E17
  1. Disconnect the H102 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H37-22 (CANH) - H37-21 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ECU (COMBINATION METER ECU - NO. 3 JUNCTION CONNECTOR)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

8.CONNECT CONNECTOR
  1. Reconnect the H104 No. 3 junction connector.


NEXT


9.CHECK FOR OPEN IN CAN BUS WIRE (MAIN BODY ECU - NO. 3 JUNCTION CONNECTOR)


    C159597E03
  1. Disconnect the H2 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H2-16 (CANP) - H2-15 (CANN)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MAIN BODY ECU (MAIN BODY ECU - NO. 3 JUNCTION CONNECTOR)
OK

REPLACE MAIN BODY ECU 

10.CONNECT CONNECTOR
  1. Reconnect the H104 No. 3 junction connector.


NEXT


11.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)


    E158732E02
  1. Disconnect the O41 No. 4 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O41-6 (CANH) - O41-12 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE (NO. 3 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)
OK


12.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - MAIN BODY ECU)


    E158732E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O41-5 (CANH) - O41-11 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 13
OK

REPAIR OR REPLACE NO. 4 JUNCTION CONNECTOR 

13.CONNECT CONNECTOR
  1. Reconnect the O41 No. 4 junction connector.


NEXT


14.CHECK FOR OPEN IN CAN BUS WIRE (MAIN BODY ECU - NO. 4 JUNCTION CONNECTOR)


    C159597E03
  1. Disconnect the H2 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H2-16 (CANP) - H2-15 (CANN)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MAIN BODY ECU (MAIN BODY ECU - NO. 4 JUNCTION CONNECTOR)
OK

REPLACE MAIN BODY ECU 

15.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR SIDE)


    E158745E02
  1. Disconnect the H104 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H37-22 (CANH) - H37-21 (CANL)
    Ignition switch off
    108 to 132 Ω
    H37-22 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H37-21 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H37-22 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H37-21 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 25
OK


16.CONNECT CONNECTOR
  1. Reconnect the H104 No. 3 junction connector.


NEXT


17.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)


    E158733E01
  1. Disconnect the O41 No. 4 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O41-6 (CANH) - O41-12 (CANL)
    Ignition switch off
    108 to 132 Ω
    O41-6 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    O41-12 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    O41-6 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    O41-12 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN MAIN WIRE (NO. 3 JUNCTION CONNECTOR - NO. 4 JUNCTION CONNECTOR)
OK


18.CONNECT CONNECTOR
  1. Reconnect the O41 No. 4 junction connector.


NEXT


19.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - POWER BACK DOOR ECU)


    E158733E02
  1. Disconnect the O42 No. 4 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O42-1 (CANH) - O42-7 (CANL)
    Ignition switch off
    1 Ω or higher
    O42-1 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    O42-7 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    O42-1 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    O42-7 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 21
OK


20.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - MAIN BODY ECU)


    E158733E03
  1. Disconnect the O41 No. 4 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O41-5 (CANH) - O41-11 (CANL)
    Ignition switch off
    108 to 132 Ω
    O41-5 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    O41-11 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    O41-5 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    O41-11 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 23
OK

REPAIR OR REPLACE NO. 4 JUNCTION CONNECTOR 

21.CONNECT CONNECTOR
  1. Reconnect the O42 No. 4 junction connector.


NEXT


22.CHECK FOR SHORT IN CAN BUS WIRES (POWER BACK DOOR ECU)


    E158746E01
  1. Disconnect the O30 power back door ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    O30-6 (CANP) - O30-5 (CANN)
    Ignition switch off
    54 to 69 Ω
    O30-6 (CANP) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    O30-5 (CANN) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    O30-6 (CANP) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    O30-5 (CANN) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER BACK DOOR ECU (NO. 4 JUNCTION CONNECTOR - POWER BACK DOOR ECU)
OK

REPLACE POWER BACK DOOR UNIT ASSEMBLY (Click here)  

23.CONNECT CONNECTOR
  1. Reconnect the O42 No. 4 junction connector.


NEXT


24.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)


    C159598E03
  1. Disconnect the H2 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H2-16 (CANP) - H2-15 (CANN)
    Ignition switch off
    108 to 132 Ω
    H2-16 (CANP) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H2-15 (CANN) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H2-16 (CANP) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H2-15 (CANN) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MAIN BODY ECU (NO. 4 JUNCTION CONNECTOR - MAIN BODY ECU)
OK

REPLACE MAIN BODY ECU 

25.CONNECT CONNECTOR
  1. Reconnect the H104 No. 3 junction connector.


NEXT


26.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - POWER SEAT CONTROL ECU)


    C159607E13
  1. Disconnect the H97 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H97-1 (CANH) - H97-2 (CANL)
    Ignition switch off
    1 Ω or higher
    H97-1 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H97-2 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H97-1 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H97-2 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 35
OK


27.CONNECT CONNECTOR
  1. Reconnect the H97 No. 3 junction connector.


NEXT


28.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - MULTIPLEX TILT AND TELESCOPIC ECU)


    C159607E14
  1. Disconnect the H96 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H96-1 (CANH) - H96-2 (CANL)
    Ignition switch off
    1 Ω or higher
    H96-1 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H96-2 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H96-1 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H96-2 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 37
OK


29.CONNECT CONNECTOR
  1. Reconnect the H96 No. 3 junction connector.


NEXT


30.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU)


    C159608E32
  1. Disconnect the H98 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H98-1 (CANH) - H98-2 (CANL)
    Ignition switch off
    1 Ω or higher
    H98-1 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H98-2 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H98-1 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H98-2 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 39
OK


31.CONNECT CONNECTOR
  1. Reconnect the H98 No. 3 junction connector.


NEXT


32.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - COMBINATION METER ECU)


    C159607E15
  1. Disconnect the H102 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H102-1 (CANH) - H102-2 (CANL)
    Ignition switch off
    108 to 132 Ω
    H102-1 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H102-2 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H102-1 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H102-2 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Result 
    Result
    Proceed to
    OK (w/o Power back door system)
    A
    NG
    B
    OK (w/ Power back door system)
    C



B
Go to step 41

C
REPAIR OR REPLACE NO. 3 JUNCTION CONNECTOR
A


33.CONNECT CONNECTOR
  1. Reconnect the H102 No. 3 junction connector.


NEXT


34.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)


    C159607E16
  1. Disconnect the H104 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H104-1 (CANH) - H104-2 (CANL)
    Ignition switch off
    108 to 132 Ω
    H104-1 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H104-2 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H104-1 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H104-2 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 43
OK

REPAIR OR REPLACE NO. 3 JUNCTION CONNECTOR 

35.CONNECT CONNECTOR
  1. Reconnect the H97 No. 3 junction connector.


NEXT


36.CHECK FOR SHORT IN CAN BUS WIRES (POWER SEAT CONTROL ECU)


    C159484E02
  1. Disconnect the X11 power seat control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    X11-5 (CANH) - X11-1 (CANL)
    Ignition switch off
    54 to 69 Ω
    X11-5 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    X11-1 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    X11-5 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    X11-1 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER SEAT CONTROL ECU (NO. 3 JUNCTION CONNECTOR - POWER SEAT CONTROL ECU)
OK

REPLACE FRONT POWER SEAT SWITCH LH (Click here)  

37.CONNECT CONNECTOR
  1. Reconnect the H96 No. 3 junction connector.


NEXT


38.CHECK FOR SHORT IN CAN BUS WIRES (MULTIPLEX TILT AND TELESCOPIC ECU)


    C159591E02
  1. Disconnect the H57 multiplex tilt and telescopic ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H57-5 (CANH) - H57-14 (CANL)
    Ignition switch off
    54 to 69 Ω
    H57-5 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H57-14 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H57-5 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H57-14 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MULTIPLEX TILT AND TELESCOPIC ECU (NO. 3 JUNCTION CONNECTOR - MULTIPLEX TILT AND TELESCOPIC ECU)
OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU (Click here)  

39.CONNECT CONNECTOR
  1. Reconnect the H98 No. 3 junction connector.


NEXT


40.CHECK FOR SHORT IN CAN BUS WIRES (OUTER MIRROR CONTROL ECU)


    C158955E03
  1. Disconnect the M8 outer mirror control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    M8-1 (CAN) - M8- 21 (CGND)
    Ignition switch off
    54 to 69 Ω
    M8-1 (CAN) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    M8-21 (CGND) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    M8-1 (CAN) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    M8-21 (CGND) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO OUTER MIRROR CONTROL ECU (NO. 3 JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU)
OK

REPLACE OUTER MIRROR CONTROL ECU (Click here)  

41.CONNECT CONNECTOR
  1. Reconnect the H102 No. 3 junction connector.


NEXT


42.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ECU)


    C158955E04
  1. Disconnect the H37 combination meter ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H37-22 (CANH) - H37-21 (CANL)
    Ignition switch off
    108 to 132 Ω
    H37-22 (CANH) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H37-21 (CANL) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H37-22 (CANH) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H37-21 (CANL) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ECU (NO. 3 JUNCTION CONNECTOR - COMBINATION METER ECU)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

43.CONNECT CONNECTOR
  1. Reconnect the H104 No. 3 junction connector.


NEXT


44.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)


    C159598E03
  1. Disconnect the H2 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    H2-16 (CANP) - H2-15 (CANN)
    Ignition switch off
    108 to 132 Ω
    H2-16 (CANP) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H2-15 (CANN) - H19-4 (CG)
    Ignition switch off
    200 Ω or higher
    H2-16 (CANP) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    H2-16 (CANP) - H19-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MAIN BODY ECU (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)
OK

REPLACE MAIN BODY ECU 

45.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)
  1. Reconnect the cable to the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

  1. Disconnect the DA, DB and DD main body ECU connectors.



  1. Measure the resistance according to the value(s) in the table below.


    E146246E04

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    DD-62 (GND1) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    DA-1 (ALTB) - Body ground
    Always
    11 to 14 V
    DB-13 (BECU) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU