Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM

AIR CONDITIONING SYSTEM > Air Conditioning Compressor Magnetic Clutch Circuit

for Preparation Click here


DESCRIPTION

When the air conditioning amplifier is turned on, a magnetic clutch ON signal is sent from the MGC terminal of the air conditioning amplifier. Then, the magnetic clutch relay (MG CLT) turns on to operate the magnetic clutch.

WIRING DIAGRAM


E146216E02


INSPECTION PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
  1. Connect the Techstream to DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Select "Communication Bus Check"

    OK:
    All ECUs and sensors connected to the CAN communication system are displayed.



NG
GO TO CAN COMMUNICATION SYSTEM (Click here)
OK


2.READ VALUE USING TECHSTREAM (A/C SIGNAL)
  1. Connect the Techstream to DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine / Data List / A/C Signal

  1. According to the display on the Techstream, read the Data List.

    ECM 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    A/C Signal
    Air conditioning switch signal /
    ON or OFF
    ON: Air conditioning ON
    OFF: Air conditioning OFF
    -

    OK:
    The display is as specified in the normal condition.



NG
Go to step 3
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

3.INSPECT FUSE (A/C IG)


    E160643E03
  1. Remove the A/C IG fuse from the main body ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A/C IG fuse
    Always
    Below 1 Ω

  1. Reinstall the A/C IG fuse.



NG
REPLACE FUSE
OK


4.INSPECT MAGNETIC CLUTCH RELAY (MG CLT)
B060778E04
  1. Remove the magnetic clutch relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    When battery voltage is not applied between terminals
    10 kΩ or higher
    When battery voltage is applied to terminals 1 and 2
    Below 1 Ω

  1. Reinstall e the magnetic clutch relay.



NG
REPLACE MAGNETIC CLUTCH RELAY
OK


5.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BATTERY)
E124470E54
  1. Disconnect the H24 air conditioning amplifier connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    H24-20 (MGC) - Body ground
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK AIR CONDITIONING AMPLIFIER (MGC VOLTAGE)
E124471E50
  1. Reconnect the H24 air conditioning amplifier connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    H24-20 (MGC) - Body ground
    Engine running and air conditioning switch ON
    Below 1 V
    Engine running and air conditioning switch OFF
    11 to 14 V



NG
REPLACE AIR CONDITIONING AMPLIFIER (Click here)
OK


7.INSPECT AIR CONDITIONING COMPRESSOR (COMPRESSOR HARNESS)
E146414E01
  1. Disconnect the D39 air conditioning compressor connector.

  1. Disconnect the magnetic clutch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (MG+) - 1
    Always
    Below 1 Ω
    3 (MG+) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR AIR CONDITIONING COMPRESSOR
OK


8.INSPECT MAGNETIC CLUTCH


    E146516E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - Body ground
    Always
    3.4 to 3.8 Ω

  1. When connector terminal 1 is connected to the positive (+) battery terminal, check that the following occurs: 1) the magnetic clutch operating sound can be heard, and 2) the magnetic clutch hub and rotor lock.
    Result 
    Result
    Proceed to
    OK
    A
    NG (for 2UZ-FE)
    B
    NG (for 3UR-FE or 3UR-FBE)
    C

  1. Reconnect the air conditioning compressor connector.

  1. Reconnect the magnetic clutch connector.



B
REPLACE MAGNETIC CLUTCH

C
REPLACE MAGNETIC CLUTCH
A


9.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING COMPRESSOR - ENGINE ROOM RELAY BLOCK)
E146415E02
  1. Disconnect the D39 air conditioning compressor connector.

  1. Remove the magnetic clutch relay (MG CLT) from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D39-3 (MG+) - Engine room relay block magnetic clutch relay terminal 3
    Always
    Below 1 Ω
    D39-3 (MG+) or Engine room relay block magnetic clutch relay terminal 3 - Body ground
    Always
    10 kΩ or higher

  1. Reinstall the magnetic clutch relay (MG CLT).

  1. Reconnect the air conditioning compressor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK - BATTERY)
E146416E01
  1. Remove the magnetic clutch relay (MG CLT) from the engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Engine room relay block magnetic clutch relay terminal 5 - Body ground
    Ignition switch ON
    11 to 14 V

  1. Reinstall the magnetic clutch relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER (Click here)