CAN COMMUNICATION SYSTEM > HOW TO PROCEED WITH TROUBLESHOOTING |
| 1.VEHICLE BROUGHT TO WORKSHOP |
| |||||
| 2.INSPECT BATTERY VOLTAGE |
| |||||
| 3.CHECK AND CLEAR DTC* |
Using the Techstream, perform the Health Check (all DTCs check).
| |||||
| 4.CHECK INSTALLED SYSTEMS (ECU AND SENSOR) THAT USE CAN COMMUNICATION |
Based on the vehicle equipment and specifications, confirm the systems that use CAN communication (Click here).
| |||||
| 5.CHECK DLC3 BRANCH WIRE AND V BUS CIRCUIT MAIN WIRE (CANH - CANL) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Measured Resistance | Proceed to |
| 6 (CANH) - 14 (CANL) | Ignition switch off | OK (54 to 69 Ω) | A |
| NG (70 Ω or higher) | B | ||
| NG (less than 54 Ω) | C |
|
| ||||
|
| ||||
| |||||
| 6.CHECK V BUS CIRCUIT +B (CANH, CANL - BAT) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 6 (CANH) - 16 (BAT) | Ignition switch off | 6 kΩ or higher |
| 14 (CANL) - 16 (BAT) |
|
| ||||
| |||||
| 7.CHECK V BUS CIRCUIT GND (CANH, CANL - CG) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 6 (CANH) - 4 (CG) | Ignition switch off | 200 Ω or higher |
| 14 (CANL) - 4 (CG) |
|
| ||||
| |||||
| 8.CHECK ECUS CONNECTED TO CAN BUS (USING TECHSTREAM)* |
Select "CAN Bus Check" from the "System Select".
Wait 1 minute and then check the display of the connected ECUs and sensors.
| Result | Proceed to |
| All ECUs and sensors connected to CAN communication system displayed on screen. | A |
| Except for main body ECU, no ECUs connected to MS bus are displayed. Main body ECU outputs MS bus trouble code (U1002) (MS bus main wire open or short malfunction). | B |
| No ECUs connected to MS bus are displayed (branch wire between main body ECU and V bus circuit is open). | C |
| ECU or sensor that should be connected to CAN communication is not displayed (ECU or sensor branch wire open). | D |
| ECU or sensor that should be connected to CAN communication is not displayed or display is intermittent during check (ECU or sensor branch wire open on one side). | E |
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| |||||
| 9.CHECK COMMUNICATION MALFUNCTION DTC (PAST DTC CHECK)* |
Select "CAN Bus Check" from the "System Select".
Write down all of the DTCs stored in each ECU.
| Result | Proceed to |
| ECU connected to V bus main wire has stored communication trouble code (V bus main wire past malfunction). | A |
| Main body ECU outputs MS bus trouble code (U1002) (MS bus past malfunction). | B |
| Main body ECU outputs trouble code other than MS bus trouble code (U1002) (past malfunction of ECU branch wire connected to MS bus). | C |
|
| ||||
|
| ||||
| |||||
| 10.CHECK DTC COMBINATION TABLE (V BUS CIRCUIT BRANCH WIRE OPEN PAST MALFUNCTION) |
Based on the combination of stored CAN communication system DTCs, determine which ECUs and sensors have a communication stop malfunction (Click here).
| |||||
| 11.PERFORM MALFUNCTION SIMULATION TEST (V BUS CIRCUIT MAIN WIRE PAST MALFUNCTION)* |
Using the Techstream, clear all DTCs.
Perform a malfunction simulation test on all harnesses and connectors related to the V bus circuit main wire.
Check the DTCs that were output as a result of the malfunction simulation test. Then determine the malfunctioning area.
| |||||
| 12.ADJUST, REPAIR AND REPLACE |
| |||||
| 13.CONFIRMATION TEST |
|
| ||||
|---|---|---|---|---|---|