Home › Engine / Hybrid System · 1UR-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P0037    Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2)

DTC    P0038    Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2)

DTC    P0057    Oxygen Sensor Heater Control Circuit Low (Bank 2 Sensor 2)

DTC    P0058    Oxygen Sensor Heater Control Circuit High (Bank 2 Sensor 2)

DTC    P0141    Oxygen Sensor Heater Circuit Malfunction (Bank 1 Sensor 2)

DTC    P0161    Oxygen Sensor Heater Circuit Malfunction (Bank 2 Sensor 2)

DTC    P102D    O2 Sensor Heater Circuit Performance Bank 1 Sensor 2 Stuck ON

DTC    P105D    O2 Sensor Heater Circuit Performance Bank 2 Sensor 2 Stuck ON

for Preparation Click here


DESCRIPTION

  1. Refer to DTC P0136 .

HINT:
  1. When any of these DTCs are stored, the ECM enters fail-safe mode. The ECM turns off the Heated Oxygen (HO2) sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.

  2. The ECM provides a pulse width modulated control circuit to adjust the current through the heater. The HO2 sensor heater circuit uses a relay on the +B side of the circuit.


    A164717E06


DTC No.
DTC Detection Condition
Trouble Area
P0037
P0057
The heater current is less than the specified value while the heater is operating.
(1 trip detection logic)
  1. Open in HO2 sensor heater circuit
  2. HO2 sensor heater (for Sensor 2)
  3. Integration relay
  4. ECM
P0038
P0058
The heater current is higher than the specified value while the heater is operating.
(1 trip detection logic)
  1. Short in HO2 sensor heater circuit
  2. HO2 sensor heater (for Sensor 2)
  3. Integration relay
  4. ECM
P0141
P0161
The cumulative heater resistance correction value exceeds the threshold.
(2 trip detection logic)
  1. Open or short in HO2 sensor heater circuit
  2. HO2 sensor heater (for Sensor 2)
  3. Integration relay
  4. ECM
P102D
P105D
The heater current is higher than the specified value while the heater is not operating.
(1 trip detection logic)
ECM

MONITOR DESCRIPTION

The sensing portion of the Heated Oxygen (HO2) sensor has a zirconia element which is used to detect the oxygen concentration in the exhaust gas. If the zirconia element is at the appropriate temperature, and the difference between the oxygen concentrations surrounding the inside and outside surfaces of the sensor is large, the zirconia element generates voltage signals. In order to increase the oxygen concentration detecting capacity of the zirconia element, the ECM supplements the heat from the exhaust with heat from a heating element inside the sensor.
  1. Heated oxygen sensor heater range check (P0037, P0038, P0057, P0058, P102D and P105D):
    The ECM monitors the current applied to the HO2 sensor heater to check the heater for malfunctions.
    If the heater current is outside the normal range, the signal transmitted by the HO2 sensor becomes inaccurate. When the current in the HO2 sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.
  1. Heated oxygen sensor heater performance (P0141 and P0161):
    After the accumulated heater ON time exceeds 100 seconds, the ECM calculates the heater resistance using the battery voltage and the current applied to the heater.
    If the resistance is above the threshold value, the ECM determines that there is a malfunction in the HO2 sensor heater and stores DTC P0141 or P0161.

MONITOR STRATEGY


Related DTCs
P0037: Heated oxygen sensor heater (for Bank 1) range check (Low electrical current)
P0038: Heated oxygen sensor heater (for Bank 1) range check (High electrical current)
P0057: Heated oxygen sensor heater (for Bank 2) range check (Low electrical current)
P0058: Heated oxygen sensor heater (for Bank 2) range check (High electrical current)
P0141: Heated oxygen sensor heater performance (for Bank 1)
P0161: Heated oxygen sensor heater performance (for Bank 2)
P102D: Heated oxygen sensor heater stuck ON (for Bank 1 Sensor 2)
P105D: Heated oxygen sensor heater stuck ON (for Bank 2 Sensor 2)
Required Sensors/Components (Main)
Heated oxygen sensor heater
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous: P0037, P0038, P0057, P0058 P102D and P105D
Once per driving cycle: P0141 and P0161
Duration
0.5 seconds: P0037 and P0057
Within 3 seconds: P0038 and P0058
10 seconds: P0141 and P0161
0.5 seconds: P102D and P105D
MIL Operation
Immediate: P0037, P0038, P0057, P0058, P102D and P105D
2 driving cycles: P0141 and P0161
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


P0037 and P0057 (Case 1) 
Monitor runs whenever following DTCs not stored
P0032, P0052 (Air fuel ratio sensor heater)
P0038, P0058 (Rear oxygen sensor heater)
Battery voltage
10.5 V or higher
Engine
Running
Starter
OFF
Catalyst active A/F control
Not operating
Time after heater ON
10 seconds or more
Learned heater OFF current operation
Complete
Heater OFF current learned value
Acquired

P0037 and P0057 (Case 2) 
Monitor runs whenever following DTCs not stored
P0031, P0032, P0051, P0052 (Air fuel ratio sensor heater)
P0038, P0058 (Rear oxygen sensor heater)
Battery voltage
10.5 V or higher
Engine
Running
Starter
OFF
Catalyst active A/F control
Not operating
Time after heater ON
10 seconds or more
Learned heater OFF current operation
Complete
Heated oxygen sensor heater OFF current
Higher than 3.5 A
Hybrid IC high current limiter port
Fail

P0038 and P0058 
Monitor runs whenever following DTCs not stored
None
Battery voltage
10.5 V or higher
Engine
Running
Starter
OFF
Catalyst active A/F control
Not operating
Time after heater ON
10 seconds or more
Learned heater OFF current operation
Complete

P0141 and P0161 (Case 1) 
Monitor runs whenever following DTCs not stored
P0031, P0032, P0051, P0052 (Air fuel ratio sensor heater)
P0037, P0038, P0057, P0058 (Rear oxygen sensor heater)
Battery voltage
10.5 V or higher
Fuel cut
OFF
Time after fuel cut ON to OFF
30 seconds or more
Accumulated heater ON time
100 seconds or more
Learned heater OFF current operation
Complete

P0141 and P0161 (Case 2) 
Monitor runs whenever following DTCs not stored
None
Duration that rear heated oxygen sensor impedance is less than 15 kΩ
2 seconds or more

P102D and P105D 
Monitor runs whenever following DTCs not stored
P0031, P0032, P0051, P0052 (Air fuel ratio sensor heater)
P0037, P0038, P0057, P0058 (Rear oxygen sensor heater)
Battery voltage
10.5 V or higher
Engine
Running
Starter
OFF
Catalyst active A/F control
Not operating
Time after heater ON
10 seconds or more
Learned heater OFF current operation
Complete
Hybrid IC high current limiter port
Fail

TYPICAL MALFUNCTION THRESHOLDS


P0037 and P0057 (Case 1) 
Heater current - Learned heater OFF current
0.3 A or less

P0037 and P0057 (Case 2) 
Heated oxygen sensor heater ON current
1 A or less

P0038 and P0058 
Hybrid IC high current limiter port
Fail
Heated oxygen sensor heater output
ON

P0141 and P0161 
Accumulated heater resistance
Varies with sensor element temperature (Example: Higher than 23 Ω)

P102D and P105D 
Heated oxygen sensor heater ON current
Higher than 1 A

COMPONENT OPERATING RANGE


Heated Oxygen (HO2) sensor heater current
0.4 to 1 A (when engine idles, HO2 sensor warmed up and battery voltage 11 to 14 V)

MONITOR RESULT

Refer to Checking Monitor Status (Click here).

CONFIRMATION DRIVING PATTERN


A198819E31

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream ON.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (Click here).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine and idle it for 5 minutes or more [B].
  7. With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].
  8. Idle the engine for 5 minutes or more [D].
  9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].
  10. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  12. Input the DTC: P0037, P0038, P0057, P0058, P0141, P0161, P102D or P105D.
  13. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  14. If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.
  15. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM

Refer to DTC P0136 .

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. Refer to "Data List / Active Test" [O2 Heater B1S2, O2 Heater B2S2, O2 Heater Curr Val B1S2 and O2 Heater Curr Val B2S2] (Click here).
  2. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  3. When the values for the Data List items O2 Heater Curr Val B1S2 and O2 Heater Curr Val B2S2 are not 0 A, the heater is on.
  4. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  5. Bank 2 refers to the bank that does not include the No. 1 cylinder.
  6. Sensor 1 refers to the sensor closest to the engine assembly.
  7. Sensor 2 refers to the sensor farthest away from the engine assembly.

1.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)
  1. Inspect the heated oxygen sensor .



NG
REPLACE HEATED OXYGEN SENSOR (Click here)
OK


2.CHECK TERMINAL VOLTAGE (+B OF HO2 SENSOR)
A149595E33
  1. Disconnect the HO2 sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D17-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V
    D18-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Heated Oxygen Sensor)
    *b
    for Bank 1
    *c
    for Bank 2
    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 5
A


3.INSPECT INTEGRATION RELAY (EFI MAIN)
  1. Inspect the integration relay (EFI relay) .



NG
REPLACE INTEGRATION RELAY (EFI MAIN)
OK


4.CHECK HARNESS AND CONNECTOR (HO2 SENSOR - INTEGRATION RELAY)
  1. Disconnect the HO2 sensor connector.

  1. Remove the integration relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D17-2 (+B) - 1B-4
    Always
    Below 1 Ω
    D18-2 (+B) - 1B-4
    Always
    Below 1 Ω
    D17-2 (+B) or 1B-4 - Body ground
    Always
    10 kΩ or higher
    D18-2 (+B) or 1B-4 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)  

5.CHECK HARNESS AND CONNECTOR (HO2 SENSOR - ECM)
  1. Disconnect the HO2 sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D17-1 (HT1B) - D56-45 (HT1B)
    Always
    Below 1 Ω
    D18-1 (HT2B) - D56-44 (HT2B)
    Always
    Below 1 Ω
    D17-1 (HT1B) or D56-45 (HT1B) - Body ground
    Always
    10 kΩ or higher
    D18-1 (HT2B) or D56-44 (HT2B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Start the engine.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Read the output pending DTCs using the Techstream.
    Result 
    Result
    Proceed to
    No pending DTC is output
    A
    Pending DTC P0037, P0038, P0057, P0058, P0141, P0161, P102D and/or P105D is output
    B



B
REPLACE ECM (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)