Home › Engine / Hybrid System ยท 1UR-FE › FUEL › FUEL INJECTOR

FUEL INJECTOR > INSTALLATION

for Preparation Click here



1. INSTALL FUEL INJECTOR ASSEMBLY
  1. Attach the 3 clamps to install the No. 6 wire harness to the delivery pipe RH.

  1. Attach the 3 clamps to install the No. 7 wire harness to the delivery pipe LH.

  1. Apply gasoline or spindle oil to a new O-ring and install it to the injector.

    NOTICE:
    Make sure that there is no damage or foreign material in the groove of the injector when installing the O-ring.



    A161427E01
  1. Connect the injector connector.



    A161479E06
  1. Install the injector to the delivery pipe as shown in the illustration.
    Text in Illustration 
    *a
    CORRECT
    *b
    INCORRECT

    NOTICE:
    1. Make sure that there are no scratches or foreign matter in or around the insertion hole of the delivery pipe.
    2. When inserting the injector, be careful not to damage the O-ring.
    3. Attach the part of the injector labeled B between the parts of the delivery pipe labeled A.



    A214319E02
  1. Check that each injector is installed to the delivery pipe facing the direction shown in the illustration.
    Text in Illustration 
    *1
    Fuel Delivery Pipe RH
    *2
    Fuel Delivery Pipe LH



2. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY LH
  1. Install the 2 delivery pipe spacers and 4 insulators to the cylinder head LH.

  1. Install the delivery pipe (with injectors) to the cylinder head LH.



    A163659E07
  1. Install the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    NOTICE:
    Make sure that the part of the injector labeled B is between the parts of the delivery pipe labeled A.

    Text in Illustration 
    *1
    Delivery Pipe
    *2
    Injector
    *a
    CORRECT
    *b
    INCORRECT

  1. Connect the No. 7 wire harness connector.



3. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY RH
  1. Install the 2 delivery pipe spacers and 4 insulators to the cylinder head RH.

  1. Install the delivery pipe (with injectors) to the cylinder head RH.



    A163659E07
  1. Install the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    NOTICE:
    Make sure that the part of the injector labeled B is between the parts of the delivery pipe labeled A.

    Text in Illustration 
    *1
    Delivery Pipe
    *2
    Injector
    *a
    CORRECT
    *b
    INCORRECT

  1. Connect the No. 6 wire harness connector.



4. CONNECT NO. 1 FUEL PIPE SUB-ASSEMBLY
  1. Connect the No. 1 fuel pipe to the fuel delivery pipe LH (Click here).



5. CONNECT FUEL TUBE SUB-ASSEMBLY
  1. Connect the fuel tube to the delivery pipe LH (Click here).

  1. Connect the fuel tube to the delivery pipe RH (Click here).



6. CONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY
  1. Connect the No. 2 fuel tube to the fuel pressure regulator (Click here).



7. INSTALL EGR VALVE BRACKET
(Click here)


8. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable some systems need to be initialized after the cable is reconnected (Click here).



9. CHECK FOR FUEL LEAK
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and Techstream on.

    NOTICE:
    Do not start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

  1. Check that there are no fuel leaks after doing maintenance anywhere on the fuel system.