DTC P0031 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1) |
DTC P0032 Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1) |
DTC P0051 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 2 Sensor 1) |
DTC P0052 Oxygen (A/F) Sensor Heater Control Circuit High (Bank 2 Sensor 1) |
DTC P101D A/F Sensor Heater Circuit Performance Bank 1 Sensor 1 Stuck ON |
DTC P103D A/F Sensor Heater Circuit Performance Bank 2 Sensor 1 Stuck ON |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0031 P0051 | Air-Fuel Ratio (A/F) sensor heater current is less than 0.8 A (1 trip detection logic) |
|
| P0032 P0052 | Air-Fuel Ratio (A/F) sensor heater current failure (1 trip detection logic) |
|
| P101D P103D | The heater current is higher than the specified value while the heater is not operating (1 trip detection logic). | ECM |
| Related DTCs | P0031: A/F sensor heater (for Bank 1) open/short (Low electrical current) P0032: A/F sensor heater (for Bank 1) open/short (High electrical current) P0051: A/F sensor heater (for Bank 2) open/short (Low electrical current) P0052: A/F sensor heater (for Bank 2) open/short (High electrical current) P101D: A/F sensor heater (for Bank 1) performance P103D: A/F sensor heater (for Bank 2) performance |
| Required Sensors/Components (Main) | A/F sensor heater |
| Required Sensors/Components (Related) | - |
| Frequency of Operation | Continuous |
| Duration | 10 seconds: P0031 and P0051 10.24 seconds: P0032 and P0052 1 seconds: P101D and P103D |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not stored | P101D, P103D (Air fuel ratio sensor heater) |
| Battery voltage | 10.5 V or higher |
| Time after engine start | 10 seconds or more |
| A/F sensor heater duty-cycle | 50% or more |
| Monitor runs whenever following DTCs not stored | None |
| Battery voltage | 10.5 V or higher |
| Time after engine start | 10 seconds or more |
| A/F sensor heater duty-cycle | More than 0% |
| Monitor runs whenever following DTCs not stored | P0031, P0051 (Air fuel ratio sensor heater) |
| Battery voltage | 10.5 V or higher |
| Time after engine start | 10 seconds or more |
| A/F sensor heater duty-cycle | 10 to 60% |
| A/F sensor heater ON current | 0.8 A or higher |
| A/F sensor heater current | Less than 0.8 A |
| Hybrid IC high current limiter port | Fail |
| Hybrid IC high current limiter port | Fail |
| A/F sensor heater current | 0.8 A or more |

| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE) |
Inspect the air fuel ratio sensor .
|
| ||||
| OK | |
| 2.CHECK TERMINAL VOLTAGE (+B OF A/F SENSOR) |
![]() |
Disconnect the A/F sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D19-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| D20-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Air Fuel Ratio Sensor) |
| *b | for Bank 1 |
| *c | for Bank 2 |
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | |
| 3.INSPECT INTEGRATION RELAY (A/F) |
Inspect the integration relay (A/F relay) .
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - A/F SENSOR AND BODY GROUND) |
Disconnect the A/F sensor connector.
Remove the integration relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D19-2 (+B) - 1A-4 | Always | Below 1 Ω |
| D20-2 (+B) - 1A-4 | Always | Below 1 Ω |
| 1A-2 - 1B-5 | Always | Below 1 Ω |
| 1A-3 - Body ground | Always | Below 1 Ω |
| D19-2 (+B) or 1A-4 - Body ground | Always | 10 kΩ or higher |
| D20-2 (+B) or 1A-4 - Body ground | Always | 10 kΩ or higher |
| 1A-2 or 1B-5 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM) |
Disconnect the A/F sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D19-1 (HA1A) - D56-22 (HA1A) | Always | Below 1 Ω |
| D20-1 (HA2A) - D56-20 (HA2A) | Always | Below 1 Ω |
| D19-1 (HA1A) or D56-22 (HA1A) - Body ground | Always | 10 kΩ or higher |
| D20-1 (HA2A) or D56-20 (HA2A) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 6.CHECK WHETHER DTC OUTPUT RECURS |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear DTCs (Click here).
Start the engine.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Read the output pending DTCs using the Techstream.
| Result | Proceed to |
| No pending DTC is output | A |
| Pending DTC P0031, P0032, P0051, P0052, P101D or P103D is output | B |
|
| ||||
| A | ||
| ||