Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > TC and CG Terminal Circuit

for Preparation Click here


DESCRIPTION

Connecting terminals TC and CG of the DLC3 causes the ECU to display DTCs by blinking the ABS warning light and slip indicator light.

WIRING DIAGRAM


C162042E04


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the VSC actuator assembly, perform zero point calibration (Click here).
  2. for 1UR-FE:
    If the ECM has been replaced, it is necessary to register the Vehicle Identification Number (VIN) (Click here).
  3. for 3UR-FE:
    If the ECM has been replaced, it is necessary to register the Vehicle Identification Number (VIN) (Click here).
  4. for 3UR-FBE:
    If the ECM has been replaced, it is necessary to register the Vehicle Identification Number (VIN) (Click here).

1.INSPECT DLC3 (TC AND CG TERMINAL)


    C151827E34
  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    H19-13 (TC) - Body ground
    Ignition switch ON
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H19-4 (CG) - Body ground
    Always
    Below 1 Ω



NG
Go to step 3
OK


2.CHECK CAN COMMUNICATION SYSTEM
  1. Check if the CAN communication DTC is output (Click here).
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


3.CHECK HARNESS AND CONNECTOR (DLC3 - ECM)
C158618E11
  1. Disconnect the A27 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H19-13 (TC) - A27-16 (TC)
    Always
    Below 1 Ω
    H19-13 (TC) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)


    C151827E35
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H19-4 (CG) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT ECM (DLC3 INPUT)


    C151827E34
  1. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  
  1. Check if the ABS warning light is blinking.
    Result 
    Result
    Proceed to
    ABS warning light is blinking
    A
    ABS warning light is not blinking (for 1UR-FE)
    B
    ABS warning light is not blinking (for 3UR-FE)
    C
    ABS warning light is not blinking (for 3UR-FBE)
    D



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)

D
REPLACE ECM (Click here)
A

REPLACE VSC ACTUATOR ASSEMBLY (Click here)