DTC B2610 Tilt Position Sensor or Tilt Motor Circuit Malfunction |

| DTC Code | Detection Condition | Trouble Area |
| B2610 | Tilt operation stops within the operation range while operating. |
|

| 1.PERFORM ACTIVE TEST USING TECHSTREAM (TILT UP/DOWN) |
![]() |
Select the Active Test, use the Techstream to generate a control command, and then check that the tilt up/down function operates normally.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Tilt Operation | Tilt operation | UP/DOWN | - |
| Result | Proceed to |
| Steering wheel does not tilt up (down). | A |
| Steering wheel tilts up (down). | B |
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT MOTOR) |

Disconnect the H57 multiplex tilt and telescopic ECU connector.
Disconnect the H58 tilt motor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| H57-10 (TIM+) - H58-2 (TIM+) | Always | Below 1 Ω |
| H57-1 (TIM-) - H58-1 (TIM-) | Always | Below 1 Ω |
| H57-10 (TIM+) - Body ground | Always | 10 kΩ or higher |
| H57-1 (TIM-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.INSPECT TILT MOTOR |
![]() |
Connect the positive (+) battery terminal to terminal 2 (TIM+) and the negative (-) battery terminal to terminal 1 (TIM-) of the tilt motor connector. Then confirm that the steering wheel tilts up.
Connect the negative (-) battery terminal to terminal 2 (TIM+) and the positive (+) battery terminal to terminal 1 (TIM-) of the tilt motor connector. Then confirm that the steering wheel tilts down.
|
| ||||
| OK | ||
| ||
| 4.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT POSITION SENSOR) |

Disconnect the H57 multiplex tilt and telescopic ECU connector.
Disconnect the H58 tilt motor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| H57-6 (VCI) - H58-4 (VCI) | Always | Below 1 Ω |
| H57-7 (TIS) - H58-5 (TIS) | Always | Below 1 Ω |
| H57-17 (E1) - H58-6 (E1) | Always | Below 1 Ω |
| H57-6 (VCI) - Body ground | Always | 10 kΩ or higher |
| H57-7 (TIS) - Body ground | Always | 10 kΩ or higher |
| H57-17 (E1) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| H57-11 (GND) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 6.INSPECT MULTIPLEX TILT AND TELESCOPIC ECU (VCI, TIS TERMINAL VOLTAGE) |
![]() |
Reconnect the H57 multiplex tilt and telescopic ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| H58-4 (VCI) - H58-6 (E1) | Ignition switch ON | 8 to 16 V |
| H58-5 (TIS) - H58-6 (E1) | Ignition switch ON | 8 to 16 V |
|
| ||||
| OK | |
| 7.INSPECT TILT POSITION SENSOR |
![]() |
Reconnect the H58 tilt motor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| H57-7 (TIS) - H57-17 (E1) | Steering tilts up or tilts down | 8 to 16 V (Pulse HI) |
| Below 1 V (Pulse LOW) |
|
| ||||
| OK | ||
| ||