DTC P0451 Evaporative Emission Control System Pressure Sensor Range / Performance |
DTC P0452 Evaporative Emission Control System Pressure Sensor / Switch Low Input |
DTC P0453 Evaporative Emission Control System Pressure Sensor / Switch High Input |
| DTC No. | Monitoring Item | Malfunction Detection Condition | Trouble Area | Detection Timing | Detection Logic |
| P0451 | Canister pressure sensor noise | Sensor output voltage fluctuates frequently within certain time period. |
|
| 2 trip |
| P0452 | Canister pressure sensor low input | EVAP pressure less than 42.1 kPa for 0.5 seconds. |
|
| 1 trip |
| P0453 | Canister pressure sensor high input | EVAP pressure more than 123.8 kPa for 0.5 seconds. |
|
| 1 trip |

| Required Sensors/Components | Canister pump module |
| Frequency of Operation | Continuous |
| Duration | 0.5 seconds: P0452 and P0453 15 seconds: P0451 |
| MIL Operation | Immediate: P0452 and P0453 2 driving cycles: P0451 |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | None |
| Atmospheric pressure (absolute pressure) | 70 to 111 kPa-a (525 to 833 mmHg-a, 21 to 33 in.Hg-a) |
| Battery voltage | 10.5 V or more |
| Intake air temperature | 4.4 to 40°C (40 to 104°F) |
| Either of following conditions met | A or B |
| A. Engine condition | Running |
| B. Time after key off | 5, 7 or 9.5 hours |
| Monitor runs whenever following DTCs not present | None |
| Battery voltage | 8 V or more |
| Starter | OFF |
| Either of following conditions met | (a) or (b) |
| (a) Ignition switch | ON |
| (b) Soak timer | ON |
| Frequency that EVAP pressure changes 0.3 kPa-g (2.25 mmHg-g) or more | 10 times or more in 10 seconds |
| EVAP pressure | Less than 42.1 kPa-a (315.8 mmHg-a) |
| EVAP pressure | More than 123.8 kPa-a (928.6 mmHg-a) |
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CONFIRM DTC AND EVAP PRESSURE |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (do not start the engine).
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Vapor Pressure Pump.
Read the EVAP (Evaporative Emission) pressure displayed on the Techstream.
| Result | Test Result | Suspected Trouble Area | Proceed to |
| P0451 | - | Canister pressure sensor | C |
| P0452 | Less than 42.1 kPa-a (315.8 mmHg-a, 13 in.Hg-a) |
| A |
| P0453 | More than 123.8 kPa-a (928.6 mmHg-a, 35 in.Hg-a) |
| B |
|
| ||||
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM) |
Turn the ignition switch off.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Suspected Trouble Area | Proceed to |
| D56-121 (PPMP) - Body ground | Always | 10 Ω or less |
| A |
| D56-121 (PPMP) - Body ground | Always | 10 kΩ or more |
| B |
|
| ||||
| A | |
| 3.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM) |
Disconnect the canister pump module connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Suspected Trouble Area | Proceed to |
| D56-121 (PPMP) - Body ground | Always | 10 kΩ or more | Short in canister pressure sensor circuit | A |
| D56-121 (PPMP) - Body ground | Always | 10 Ω or less | Short in wire harness/connector (ECM - Canister pressure sensor) | B |
|
| ||||
|
| ||||
| 4.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM) |
Disconnect the canister pump module connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O24-2 (SGND) - Body ground | Always | 100 Ω or less |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| O24-4 (VCC) - Body ground | Ignition switch ON | 4.5 to 5.5 V |
| O24-3 (VOUT) - Body ground | Ignition switch ON | 4.5 to 5.5 V |
| Result | Suspected Trouble Area | Proceed to |
| Voltage and resistance within standard ranges | Open in canister pressure sensor circuit | A |
| Voltage and resistance outside standard ranges | Open in wire harness/connector (ECM - Canister pressure sensor) | B |
|
| ||||
| A | |
| 5.REPLACE CANISTER POMP MODULE |
Replace the canister pump module (Click here).

| *1 | Fuel tank vent hose | *2 | Air inlet port |
| *3 | Vent hose | - | - |
| *a | Inspection area (Check for disconnection and/or cracks) | - | - |
|
| ||||
| 6.REPAIR OR REPLACE HARNESS OR CONNECTOR (CANISTER PUMP MODULE - ECM) |
|
| ||||
| 7.REPLACE ECM |
Replace the ECM (Click here).
| NEXT | |
| 8.CHECK WHETHER DTC OUTPUT RECURS (AFTER REPAIR) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0451, P0452 or P0453.
Check the DTC judgment result.
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| NEXT | ||
| ||