Home › Engine / Hybrid System · 1UR-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P2440    Secondary Air Injection System Switching Valve Stuck Open Bank1

DTC    P2441    Secondary Air Injection System Switching Valve Stuck Close Bank1

DTC    P2442    Secondary Air Injection System Switching Valve Stuck Open Bank 2

DTC    P2443    Secondary Air Injection System Switching Valve Stuck Closed Bank 2

for Preparation Click here


DESCRIPTION

Refer to DTC P0412 .

DTC No.
DTC Detection Condition
Trouble Area
P2440
P2442
Pressure sensor detects pulsation of exhaust gas despite ECM commanding Air Switching Valve (ASV) to close while engine running
(1 trip detection logic)
  1. ASV
  2. Open or short in ASV circuit
  3. Pressure sensor
  4. Pressure sensor circuit
  5. Air Injection Control Driver (AID)
  6. ECM
P2441
P2443
Pressure sensor detects no pulsation of exhaust gas despite ECM commanding Air Switching Valve (ASV) to open while engine running
(2 trip detection logic)
  1. ASV
  2. Open or short in ASV circuit
  3. Vacuum hose (ASV - pressure sensor)
  4. Air injection hose
  5. Pressure sensor
  6. Pressure sensor circuit
  7. Air Injection Control Driver (AID)
  8. ECM

HINT:
Air switching valve normal operation:
When the Air Switching Valve (ASV) is open, exhaust gas pulsation occurs in the secondary air passage.
When the ASV is closed, exhaust gas pulsation does not occur in the secondary air passage.


MONITOR DESCRIPTION

The ECM monitors the pressure in the secondary air passage using the pressure sensor connected to the ASV of the Secondary Air Injection (AIR) system.
If either of the following conditions occurs, the ECM interprets it as a malfunction of the AIR system, and illuminates the MIL and stores a DTC:
  1. Exhaust gas pulsation is detected by the pressure sensor despite the ECM commanding the ASV to close.
  2. Exhaust gas pulsation is not detected by the pressure sensor despite the ECM commanding the ASV to open.

MONITOR STRATEGY


Related DTCs
P2440: Air control valve stuck open
P2441: Air control valve stuck closed
P2442: Air control valve stuck open
P2443: Air control valve stuck closed
Required Sensors/Components (Main)
Pressure sensor
Required Sensors/Components (Related)
-
Frequency of Operation
Once per drive cycle
Duration
2 seconds: Case 2
7 seconds: Others
MIL Operation
1 driving cycle: Case 2
2 driving cycles: Others
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All 
Monitor runs whenever following DTCs not present
P0010, P0020 (VVT oil control valve)
P0011, P0021 (VVT system - Advance)
P0012, P0022 (VVT system - Retard)
P0013, P0023 (Exhaust VVT oil control valve)
P0014, P0024 (Exhaust VVT system - Advance)
P0015, P0025 (Exhaust VVT system - Retard)
P0016, P0018 (VVT system - Misalignment)
P0017, P0019 (Exhaust VVT system - Misalignment)
P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater)
P006A, P0107, P0108 (Manifold absolute pressure)
P0102, P0103 (Mass air flow meter)
P0112, P0113 (Intake air temperature sensor)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P014C, P014D, P014E, P014F, P015A, P015B, P015C, P015D, P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256 (Front oxygen/Air fuel ratio sensor)
P0171, P0172, P0174, P0175 (Fuel system)
P0301 - P0308 (Misfire)
P0327, P0328, P0332, P0333, P032C, P032D, P033C, P033D (Knock sensor)
P0335 (Crankshaft position sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor)
P0351 - P0358 (Igniter)
P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor)
P0401 (EGR system)
P0451, P0452, P0453 (EVAP system)
P0500 (Vehicle speed sensor)
P106B (Evap. emission control system pressure sensor - Air injection system pressure sensor correlation)
P1340 (Camshaft position sensor)
P1613, P1614 (Secondary air injection driver)
P2431, P2432, P02433, P2436, P2437, P2438 (Secondary air injection system pressure sensor)
Battery voltage
11 V or more
Atmospheric pressure
45 kPa (338 mmHg) or more
Engine
Running
AIR monitor during AIR: ON*1
Completed
AIR monitor during AIR: OFF*2
Completed
AIR injection driver fail (open/short or out of range)
Not detected
AIR pressure sensor fail (open/short or out of range)
Not detected

*1: AIR monitor during AIR: ON 
Time after AIR in operation
5 seconds or more
AIR pump
ON
AIR valve
Open
Engine speed
400 to 3750 rpm
Intake air amount
Less than 100 gm/s
Time after engine start
1 second or more

*2: AIR monitor during AIR: OFF 
Time after AIR in operation
10 seconds or more
AIR pump
OFF
AIR valve
Close
Engine speed
Below 3000 rpm
AIR monitor during AIR: ON
Completed
Time after engine start
1 second or more

P2440, P2442 AIR valve is stuck open (Case 2) 
One of the following conditions is met
(a), (b) or (c)
(a) Cumulative intake air amount
100 gm/s or more
(b) Difference between starting temperature and current temperature
10°C (18°F) or higher
(c) Starting coolant temperature
45°C (113°F) or higher
AIR pump
OFF
AIR valve
Close
Engine speed
5000 rpm or less
AIR pressure sensor fail (open/short or out of range)
Not detected
Time after engine started
1 second or more
Time after AIR in operation
10 seconds or more
AIR open stuck (DTC P2440, P2442)
Not detected
AIR pressure sensor open stuck (DTC P2445, P2447)
Not in operation
Engine load
20% or more

TYPICAL MALFUNCTION THRESHOLDS


AIR ON Condition 1 
Both conditions are met during AIR ON
-
Cumulative pressure pulsation
18 kPa or higher
AIR pressure
1.9 kPa or higher

AIR ON Condition 2 
Both conditions are met during AIR ON
-
Cumulative pressure pulsation
18 kPa or higher
AIR pressure
Below 1.9 kPa

AIR ON Condition 3 
Both conditions are met during AIR ON
-
Cumulative pressure pulsation
Below 18 kPa
AIR pressure
1.9 kPa or higher

AIR ON Condition 4 
Both conditions are met during AIR ON
-
Cumulative pressure pulsation
Below 18 kPa
AIR pressure
Below 1.9 kPa

AIR OFF Condition 1 
Both conditions are met during AIR OFF
-
Cumulative pressure pulsation
25 kPa or higher
AIR pressure
3 kPa or higher

AIR OFF Condition 2 
Both conditions are met during AIR OFF
-
Cumulative pressure pulsation
25 kPa or higher
AIR pressure
Below 3 kPa

AIR OFF Condition 3 
Both conditions are met during AIR OFF
-
Cumulative pressure pulsation
Below 25 kPa
AIR pressure
3 kPa or higher

AIR OFF Condition 4 
Both conditions are met during AIR OFF
-
Cumulative pressure pulsation
Below 25 kPa
AIR pressure
Below 3 kPa

P2440, P2442 AIR valve is stuck open (Case 1) 
Either condition is met
(a) or (b)
(a) AIR OFF Condition 1
Met
(b) AIR OFF Condition 2
Met

P2441, P2443 AIR valve is stuck closed 
Either condition is met
(a) or (b)
(a) AIR ON Condition 3
Met
(b) AIR ON Condition 4
Met

P2440, P2442 AIR valve is stuck open (Case 2) 
Cumulative pressure pulsation
75 kPa or higher

MONITOR RESULT

Refer to Checking Monitor Status (Click here).

CONFIRMATION DRIVING PATTERN

NOTICE:
  1. This Air Injection Check only allows technicians to operate the AIR system for a maximum of 5 seconds.
    Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.
    While AIR system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR).
    If ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.
  2. Performing the Air Injection Check repeatedly may cause damage to the AIR system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.
  3. When performing the Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
  4. Turn the ignition switch off when the Air Injection Check operation finishes.

  1. Start the engine and warm it up.
  2. Turn the ignition switch off.
  3. Connect the Techstream to the DLC3.
  4. Turn the ignition switch to ON.
  5. Turn the Techstream on.
  6. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (Click here).
  7. Turn the ignition switch off and wait for at least 30 seconds.
  8. Turn the ignition switch to ON and turn the Techstream on.
  9. Enter the following menus: Powertrain / Engine and ECT / Utility / Air injection check / Automatic Mode.
  10. Start the engine after the Techstream initialization is finished.
  11. Perform the System Check operation by pressing ENTER (Next).
  12. Perform the following to confirm the AIR system pending codes: Press ENTER (Exit).
  13. Check for pending DTCs.

    OK:
    No pending DTC is output.

  14. After the "Air injection check" is completed, check for All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  15. Input the DTC: P2440, P2441, P2442 or P2443.
  16. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  17. If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If no permanent DTC is output, the system is normal.
    2. If a permanent DTC is output, the system is malfunctioning.

  18. Turn the ignition switch off.

WIRING DIAGRAM

Refer to DTC P0412 .

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Refer to "Data List / Active Test" [Air Pump Pressure (Absolute), Air Pump2 Pressure (Absolute) and Air Pump Pulsation Pressure] (Click here).

HINT:
Determination by ECM monitoring:
The ECM locates malfunctions in the Secondary Air Injection (AIR) system by detecting the pressure in the AIR passage between the air pump and Air Switching Valve (ASV) and stores a DTC. Soon after a cold engine start, the monitor runs for a short time while the AIR system is both ON and OFF. The ECM detects both the pressure and the exhaust pulsation and compares them.
The following 8 patterns are AIR system pressure conditions in the AIR system passage.


Pressure Condition in Secondary Air Injection System Case 1 
Air Pump
ON
Air Switching Valve
Open
Pressure
1.9 kPa or more
Pulsation Detection
Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 2 
Air Pump
OFF
Air Switching Valve
Open
Pressure
Less than 3.0 kPa
Pulsation Detection
Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 3 
Air Pump
ON
Air Switching Valve
Closed
Pressure
1.9 kPa or more
Pulsation Detection
Exhaust gas pulsation not detected

Pressure Condition in Secondary Air Injection System Case 4 
Air Pump
OFF
Air Switching Valve
Closed
Pressure
Less than 3.0 kPa
Pulsation Detection
Exhaust gas pulsation not detected

Pressure Condition in Secondary Air Injection System Case 5 
Air Pump
ON
Air Switching Valve
Open
Pressure
1.9 kPa or more
Pulsation Detection
Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 6 
Air Pump
OFF
Air Switching Valve
Open
Pressure
Less than 3.0 kPa
Pulsation Detection
Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 7 
Air Pump
ON
Air Switching Valve
Closed
Pressure
1.9 kPa or more
Pulsation Detection
Exhaust gas pulsation not detected

Pressure Condition in Secondary Air Injection System Case 8 
Air Pump
OFF
Air Switching Valve
Closed
Pressure
Less than 3.0 kPa
Pulsation Detection
Exhaust gas pulsation not detected
If the detected pressure is high, the air pump is assumed to be ON and if it alternates sharply, the ASV is assumed to be open. The ECM locates malfunctions from the combination of pressures detected when the AIR system is ON and OFF.

HINT:
The exhaust pulsation value is calculated in the ECM. If the calculated value exceeds a certain level, the ECM determines that the exhaust pulsation is in the AIR system.

HINT:
  1. In case 3 and 7, as the pressure sensor detects a slight pump operation pulsation, the detected value is not constant. Since the pump outlet is blocked by closing the ASV, the average pressure is higher than in case 1 (approximately 18 to 25 kPa).
  2. In case 1, the average pressure is approximately 3 to 11 kPa. The value of 1.9 kPa indicated in the table above is a threshold for detecting pump malfunctions.


Detected Condition while AIR Operating:
Air Pump ON, ASV Open
Detected Condition while AIR not Operating:
Air Pump OFF, ASV Closed
ECM Determination
DTC Output
Case 1
Case 8
Normal
-
Case 1
Case 6
ASV stuck open
P2440
or
P2442
Case 1
Case 7
Air pump stuck ON
P2444
or
P2446
Case 2
Case 8
Air pump stuck OFF
P2445
or
P2447
Case 3
Case 8
ASV stuck closed
P2441
or
P2443
Case 1
Case 5
ASV stuck open and air pump stuck ON
P2440 and P2444
or
P2442 and P2446
Case 2
Case 6
ASV stuck open and air pump stuck OFF
P2440 and P2445
or
P2442 and P2447
Case 3
Case 7
ASV stuck closed and air pump stuck ON
P2441 and P2444
or
P2443 and P2446
Case 4
Case 8
ASV stuck closed and air pump stuck OFF
P2441 and P2445
or
P2443 and P2447

HINT:
  1. By using the Techstream to perform the Air Injection Check operation in the System Check, the air-fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions. Furthermore, pending codes also can be checked by performing Utility / Air Injection Check / Automatic Mode after the repair.
  2. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

  1. System Check:
  2. The pressure in the secondary air passage can be checked using the Techstream.
    1. Start the engine and warm it up.
    2. Turn the ignition switch off.
    3. Connect the Techstream to the DLC3.
    4. Turn the ignition switch to ON.
    5. Turn the Techstream on.
    6. Enter the following menus: Powertrain / Engine and ECT / Utility / Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV1: OPEN, AIR PUMP 2: ON, ASV2: OPEN and AIR PUMP 1: OFF, ASV1 CLOSE, AIR PUMP 2: OFF, ASV2 CLOSE.

      HINT:
      When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.

    7. Start the engine.
    8. Perform the AIR system forced operation while the engine is idling.
    9. Check that the air pump (AIR PUMP), ASV and pressure in the AIR system passage (PRESSURE) displayed on the Techstream indicate the conditions shown in the table below.

      Standard:

      Tester Operation
      Air Pump
      ASV
      Pressure*1
      Pulsation*2
      AIR PUMP: ON, ASV: OPEN
      ON
      OPEN
      1.9 kPa or more
      18 kPa or more
      AIR PUMP: OFF, ASV: CLOSE
      OFF
      CLOSE
      Less than 3.0 kPa
      Less than 25 kPa

      *1: Average pumping pressure (gauge pressure). The pressure should be 1.9 kPa or more when the AIR system operates.
      *2: The cumulative exhaust pulsation calculated by the ECM. If the calculated value exceeds a certain level, the ECM determines that the exhaust pulsation is in the AIR system.
    10. Turn the ignition switch off.

      NOTICE:
      1. This Air Injection Check only allows technicians to operate the AIR system for a maximum of 5 seconds.
        Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.
        While AIR system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR).
        If ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.
      2. Performing the Air Injection Check repeatedly may cause damage to the AIR system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.
      3. When performing the Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
      4. Turn the ignition switch off when the Air Injection Check operation finishes.

      HINT:
      1. Bank 1 refers to the bank that includes the No. 1 cylinder*.
        *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
      2. Bank 2 refers to the bank that does not include the No. 1 cylinder.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO SECONDARY AIR INJECTION SYSTEM DTCS)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    P2440, P2441, P2442 and/or P2443 is output
    A
    P2440, P2441, P2442 and/or P2443 and P0412 and/or P0415 are output
    B
    P2440, P2441, P2442 and/or P2443 and other DTCs (except P0412 and P0415) are output
    C

If any DTCs other than P0412, P0415, P2440, P2441, P2442 and/or P2443 are output, troubleshoot those DTCs first.


B
GO TO AIR SWITCHING VALVE INSPECTION PROCEDURE (P0412 AND P0415)

C
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (SECONDARY AIR INJECTION SYSTEM OPERATION)
A211728E03
Text in Illustration 
*a
for Bank 1
*b
for Bank 2
  1. Visual check:

    1. Start the engine and warm it up.

    2. Turn the ignition switch off.

    3. Disconnect the No. 1 air hose.

    4. Connect the Techstream to the DLC3.

    5. Turn the ignition switch to ON.

    6. Turn the Techstream on.

    7. Enter the following menus: Powertrain / Engine and ECT / Utility / Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV1: OPEN, AIR PUMP 2: ON, ASV2: OPEN.

      HINT:
      When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AP and ASV operation can be selected.

    8. Start the engine.

    9. Perform the AIR system forced operation while the engine is idling.

    10. Place your hand near the air switching valve port and check that the exhaust gas pressure pulsates when the ASV is turned ON.

      CAUTION:
      To avoid the danger of being burned by the exhaust gas, bring your hand close to the valve port slowly.

    11. Enter the following menus: Powertrain / Engine and ECT / Utility / Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV1: OPEN, AIR PUMP 2: ON, ASV2: OPEN and AIR PUMP 1: ON, ASV1: CLOSE, AIR PUMP 2: ON, ASV2: CLOSE.

    12. Check that the exhaust gas does not pulsate when the ASV is turned OFF.

    13. Turn the ignition switch off.

      NOTICE:
      1. This Air Injection Check only allows technicians to operate the AIR system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.
        While AIR system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR).
        If ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.
      2. Performing the Air Injection Check repeatedly may cause damage to the AIR system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.
      3. When performing the Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
      4. Turn the ignition switch off when the Air Injection Check operation finishes.

      OK:
      Air Pump Operation
      ASV Operation
      Exhaust Gas Pulsation
      ON
      OFF
      Not detected
      ON
      ON
      Detected

  1. Other inspection method:
    The ASV operation can be confirmed by checking the cumulative pressure pulsation* provided in the System Check.
    Perform System Check operation under Manual Mode.
    *: The exhaust pulsation value is calculated in the ECM. If the calculated value exceeds a certain level, the ECM determines that the exhaust pulsation is in the AIR system.

    1. Start the engine and warm it up.

    2. Turn the ignition switch off.

    3. Connect the Techstream to the DLC3.

    4. Turn the ignition switch to ON.

    5. Turn the Techstream on.

    6. Enter the following menus: Powertrain / Engine and ECT / Utility / Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV1: OPEN, AIR PUMP 2: ON, ASV2: OPEN and AIR PUMP 1: OFF, ASV1: CLOSE, AIR PUMP 2: OFF, ASV2: CLOSE.

    7. Start the engine after the Techstream initialization is finished.

    8. Perform the AIR system forced operation while the engine is idling.

    9. Check that the air-fuel ratio and pressure in the secondary air injection system passage (PULSATION) displayed on the Techstream indicate the conditions shown in the table below.

    10. Turn the ignition switch off.


Standard:

AIR System Operation
Pulsation Condition
(ECM Calculation)
Air-Fuel Ratio
(Reference)
AIR PUMP: ON, ASV: OPEN
18 kPa or more
18 or more
AIR PUMP: OFF, ASV: CLOSE
Less than 25 kPa
Approximately 14.5
(around stoichiometric air-fuel ratio)

Reference:
If the air pump operation is confirmed as normal (Click here), the air-fuel ratio detected in front of the three-way catalytic converter changes in response to the secondary air pumped into the exhaust port when the air pump operates.
Result 
Result
Proceed to
NG
A
OK
B


B
Go to step 10
A


3.INSPECT AIR TUBE (BLOCKAGE AND LEAK)
A211729E03
  1. Check that the No. 2 and No. 3 air tubes are securely connected to both the exhaust manifold and the ASV.

  1. Inspect the air tube for blockages and damage.

    OK:
    No blockages in or damage to air tubes.

Text in Illustration 
*a
for Bank 1
*b
for Bank 2


NG
REPLACE AIR TUBE
OK


4.INSPECT AIR SWITCHING VALVE
  1. Inspect the air switching valve for bank 1 .
    Inspect the air switching valve for bank 2 .



NG
REPLACE AIR SWITCHING VALVE
OK


5.INSPECT AIR INJECTION CONTROL DRIVER (POWER SOURCE OF AIR INJECTION CONTROL DRIVER)
A162305E14
  1. Disconnect the AID connectors.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to AID for bank 1)
    *b
    Front view of wire harness connector
    (to AID for bank 2)
    *c
    Front view of wire harness connector
    (to AID for bank 1)
    *d
    Front view of wire harness connector
    (to AID for bank 2)

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D31-1 (BATT) - Body ground
    Always
    11 to 14 V (near battery voltage)
    D32-5 (+B) - Body ground
    Ignition switch ON
    11 to 14 V (near battery voltage)
    D33-1 (BAT2) - Body ground
    Always
    11 to 14 V (near battery voltage)
    D34-5 (+B2) - Body ground
    Ignition switch ON
    11 to 14 V (near battery voltage)

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D32-1 (E) - Body ground
    Always
    Below 1 Ω
    D34-1 (E2) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE AIR INJECTION CONTROL DRIVER POWER SOURCE CIRCUIT
OK


6.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER)
  1. Disconnect the ECM connectors.

  1. Disconnect the AID connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D56-28 (AIRV) - D32-3 (SIV)
    Always
    Below 1 Ω
    A27-43 (ARV2) - D34-3 (SIV2)
    Always
    Below 1 Ω
    D56-28 (AIRV) or D32-3 (SIV) - Body ground
    Always
    10 kΩ or higher
    A27-43 (ARV2) or D34-3 (SIV2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.PERFORM ACTIVE TEST USING TECHSTREAM
A242126E07
  1. Disconnect the AID connectors.

Text in Illustration 
*a
for Bank 1
*b
Front view of wire harness connector:
(to AID for Bank 1)
*c
for Bank 2
*d
Front view of wire harness connector:
(to AID for Bank 2)
  1. Connect terminals DI and SIV or DI2 and SIV2 of the wire harness connector for the AID.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV 1: OPEN or AIR PUMP 2: ON, ASV 2: OPEN.

    HINT:
    When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.

  1. Start the engine.

  1. Perform the AIR system forced operation while the engine is idling.

  1. Measure the voltage between the SIV and E or SIV2 and E2 terminals of the ECM connector when the AIR system is ON and OFF.

  1. Turn the ignition switch off.

    NOTICE:
    1. Performing Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
    2. When performing the Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch to ON or the engine running.
    3. Turn the ignition switch off when the Air Injection Check operation finishes.


    Standard Voltage:

    Tester Connection
    Condition
    Specified Condition
    D32-3 (SIV) - D32-1 (E)
    AIR PUMP: ON, ASV: OPEN
    0.5 to 2 V
    D34-3 (SIV2) - D34-1 (E2)
    AIR PUMP: ON, ASV: OPEN
    0.5 to 2 V
    D32-3 (SIV) - D32-1 (E)
    AIR PUMP: OFF, ASV: CLOSE
    11 to 14 V
    D34-3 (SIV2) - D34-1 (E2)
    AIR PUMP: OFF, ASV: CLOSE
    11 to 14 V



    A242126E06
  1. Connect terminals DI and SIP or DI2 and SIP2 of the wire harness connector for the AID.
    Text in Illustration 
    *a
    for Bank 1
    *b
    Front view of wire harness connector:
    (to AID for Bank 1)
    *c
    for Bank 2
    *d
    Front view of wire harness connector:
    (to AID for Bank 2)

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV 1: OPEN or AIR PUMP 2: ON, ASV 2: OPEN.

    HINT:
    When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.

  1. Start the engine.

  1. Perform the AIR system forced operation while the engine is idling.

  1. Measure the voltage between the SIP and E or SIP2 and E2 terminals of the ECM connector when the AIR system is ON and OFF.

  1. Turn the ignition switch off.

    NOTICE:
    1. Performing Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
    2. When performing the Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch to ON or the engine running.
    3. Turn the ignition switch off when the Air Injection Check operation finishes.


    Standard Voltage:

    Tester Connection
    Condition
    Specified Condition
    D32-4 (SIP) - D32-1 (E)
    AIR PUMP: ON, ASV: OPEN
    0.5 to 2 V
    D34-4 (SIP2) - D34-1 (E2)
    AIR PUMP: ON, ASV: OPEN
    0.5 to 2 V
    D32-4 (SIP) - D32-1 (E)
    AIR PUMP: OFF, ASV: CLOSE
    11 to 14 V
    D34-4 (SIP2) - D34-1 (E2)
    AIR PUMP: OFF, ASV: CLOSE
    11 to 14 V



NG
REPLACE ECM (Click here)
OK


8.REPLACE AIR INJECTION CONTROL DRIVER
  1. Replace the air injection control driver (Click here).


NEXT


9.CHECK WHETHER DTC OUTPUT RECURS (DTC P2440, P2441, P2442 AND/OR P2443)
  1. Start the engine and warm it up.

  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (if set) (Click here).

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Air Injection Check / Automatic Mode.

  1. Start the engine after the Techstream initialization is finished.

  1. Perform the System Check operation by pressing ENTER (Next).

  1. After operating the AIR system, perform the following to confirm the AIR system pending codes: Press the Exit button.

  1. Check pending DTCs.

  1. Turn the ignition switch off.

    OK:
    No pending DTC output.

    NOTICE:
    1. When performing the Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
    2. Turn the ignition switch off when the Air Injection Check operation finishes.



NG
REPLACE ECM (Click here)
OK

END 

10.INSPECT AIR SWITCHING VALVE (PRESSURE SENSOR)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Air pump pressure (Absolute) and Air Pump2 Pressure (Absolute).

  1. Check the pressure displayed on the Techstream.

    Standard pressure:
    45 to 135 kPa

    HINT:
    The Techstream displays the air pump pressure as absolute pressure.



NG
REPLACE AIR SWITCHING VALVE
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)