DTC B1790 Center Airbag Sensor Assembly Communication Circuit Malfunction |
| DTC Code | DTC Detection Condition | Trouble Area |
| B1790 | One of following conditions is met:
|
|

| 1.CHECK FOR DTC |
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Using the Techstream, check for DTCs of the occupant classification ECU (Click here).
|
| ||||
| OK | ||
| ||
| 2.CHECK CONNECTION OF CONNECTOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the occupant classification ECU and the center airbag sensor.
|
| ||||
| OK | |
| 3.CHECK CONNECTOR |
Check that the connectors (on the center airbag sensor side and occupant classification ECU side) are not damaged (Click here).
| Result | Proceed to |
| Connectors are not deformed or damaged (for Power seat) | A |
| Connectors are not deformed or damaged (for Manual seat) | B |
| Connectors are deformed or damaged | C |
|
| ||||
|
| ||||
| A | |
| 4.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT |
![]() |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| W6-8 (FSR+) - Body ground | Ignition switch ON | Below 1 V |
| W6-4 (FSR-) - Body ground |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 12 (FSP+) and 13 (FSP-) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| W6-8 (FSR+) - W6-4 (FSR-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| W6-8 (FSR+) - W6-4 (FSR-) | Always | 1 MΩ or higher |
| W6-8 (FSR+) - Body ground | ||
| W6-4 (FSR-) - Body ground |
|
| ||||
| OK | |
| 5.CHECK FOR DTC |
Connect the connectors to the occupant classification ECU and the center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Using the Techstream, check for DTCs of the occupant classification ECU (Click here).
|
| ||||
| OK | ||
| ||
| 6.REPLACE OCCUPANT CLASSIFICATION ECU |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Replace the occupant classification ECU (Click here).
| NEXT | |
| 7.PERFORM ZERO POINT CALIBRATION |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Using the Techstream, perform the zero point calibration (Click here).
| NEXT | |
| 8.PERFORM SENSITIVITY CHECK |
Using the Techstream, perform the sensitivity check (Click here).
| NEXT | |
| 9.CHECK FOR DTC |
Connect the connector to the occupant classification ECU.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Using the Techstream, check for DTCs of the occupant classification ECU (Click here).
|
| ||||
| OK | ||
| ||
| 10.CHECK FRONT SEAT WIRE RH |
![]() |
Disconnect the front seat wire RH connector from the No. 2 floor wire.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| PW1-8 (FSP+) - Body ground | Ignition switch ON | Below 1 V |
| PW1-9 (FSP-) - Body ground |
Turn the ignition switch off.
Disconnect the connector from the occupant classification ECU.
Using a service wire, connect terminals 8 (FSR+) and 4 (FSR-) of connector E.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| PW1-8 (FSP+) - PW1-9 (FSP-) | Always | Below 1 Ω |
Disconnect the service wire from connector E.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| PW1-8 (FSP+) - PW1-9 (FSP-) | Always | 1 MΩ or higher |
| PW1-8 (FSP+) - Body ground | ||
| PW1-9 (FSP-) - Body ground |
|
| ||||
| OK | ||
| ||
| 11.CHECK NO. 2 FLOOR WIRE |
![]() |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| P14-8 (FSR+) - Body ground | Ignition switch ON | Below 1 V |
| P14-4 (FSR-) - Body ground |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 12 (FSP+) and 13 (FSP-) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| P14-8 (FSR+) - P14-4 (FSR-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| P14-8 (FSR+) - P14-4 (FSR-) | Always | 1 MΩ or higher |
| P14-8 (FSR+) - Body ground | ||
| P14-4 (FSR-) - Body ground |
|
| ||||
| OK | |
| 12.CHECK FOR DTC |
Connect the connectors to the occupant classification ECU and the center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Using the Techstream, check for DTCs of the occupant classification ECU (Click here).
|
| ||||
| OK | ||
| ||
| 13.REPLACE OCCUPANT DETECTION ECU |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Replace the occupant classification ECU (Click here).
| NEXT | |
| 14.PERFORM ZERO POINT CALIBRATION |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Using the Techstream, perform the zero point calibration (Click here).
| NEXT | |
| 15.PERFORM SENSITIVITY CHECK |
Using the Techstream, perform the sensitivity check (Click here).
| NEXT | |
| 16.CHECK FOR DTC |
Connect the connector to the occupant classification ECU.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Using the Techstream, check for DTCs of the occupant classification ECU (Click here).
|
| ||||
| OK | ||
| ||