Home › Audio/Visual/Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM

AUDIO AND VISUAL SYSTEM > Radio Receiver Communication Error

for Preparation Click here


WIRING DIAGRAM


E189530E09


INSPECTION PROCEDURE

1.IDENTIFY COMPONENT SHOWN BY SUB-CODE


  1. Enter the diagnostic mode.


    E146440E06

  1. Press the preset switch "channel 3" to change to "Detailed Information Mode".

  1. Identify the component shown by the sub-code.

    HINT:
    1. "190 (radio receiver assembly)" is the component shown by the sub-code in the example shown in the illustration.
    1. For details of the DTC display, refer to "DTC Check/Clear" (Click here).


NEXT


2.CHECK COMPONENT SHOWN BY SUB-CODE
  1. Select the component which has stored this code.

    HINT:
    The "Bluetooth" handsfree module is built into the radio receiver assembly. If there is a problem between the "Bluetooth" handsfree module and radio receiver assembly, replace the radio receiver assembly.

    Component Table 
    Component
    Proceed to
    Except "Bluetooth" handsfree module and satellite radio tuner
    A
    "Bluetooth" handsfree module (19D)
    B
    Satellite radio tuner (1F1)*
    1. *: w/ Satellite Radio



B
REPLACE RADIO RECEIVER ASSEMBLY (Click here)
A


3.CHECK POWER SOURCE CIRCUIT OF COMPONENT SHOWN BY SUB-CODE
  1. Inspect the power source circuit of the component shown by the sub-code.

    HINT:
    If the power source circuit is operating normally, proceed to the next step.


    Component Table 
    Component
    Proceed to
    Stereo component amplifier assembly (440)*1
    Stereo Component Amplifier Power Source Circuit (Click here)
    Multi-media interface ECU (388)*3
    Multi-media Interface ECU Power Source Circuit (Click here)
    Television display assembly (1B0)*2
    Television Display Assembly Power Source Circuit (Click here)
    1. *1: for 14 Speakers
    2. *2: w/ Rear Seat Entertainment System
    3. *3: w/ USB Audio System


NEXT


4.INSPECT RADIO RECEIVER ASSEMBLY


    E145834E17
  1. Disconnect the I4*1 and I8*2 radio receiver assembly connectors.

    1. *1: for 14 Speakers
    2. *2: w/ USB Audio System

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I4-5 (ATX+) - I4-15 (ATX-)*1
    Always
    60 to 80 Ω
    I8-9 (TXM+) - I8-10 (TXM-)*2
    Always
    60 to 80 Ω

    1. *1: for 14 Speakers
    2. *2: w/ USB Audio System



NG
REPLACE RADIO RECEIVER ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - COMPONENT SHOWN BY SUB-CODE)

HINT:
  1. Start the check from the circuit that is near the component shown by the sub-code first.
  1. For details of the connectors, refer to "Terminals of ECU" (Click here).

  1. Referring to the wiring diagram below, check the AVC-LAN circuit between the radio receiver assembly and the component shown by the sub-code.

    1. Disconnect all connectors between the radio receiver assembly and the component shown by the sub-code.

    2. Check for an open or short in the AVC-LAN circuit between the radio receiver assembly and the component shown by the sub-code.

      OK:
      There is no open or short circuit.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.REPLACE COMPONENT SHOWN BY SUB-CODE
  1. Replace the component shown by the sub-code with a normal one and check if the same problem occurs again.

    OK:
    Same problem does not occur.



NG
REPLACE RADIO RECEIVER ASSEMBLY (Click here)
OK

END