Home › Engine / Hybrid System · 3UR-FBE › ENGINE CONTROL › SFI SYSTEM

SFI SYSTEM > VC Output Circuit

for Preparation Click here


DESCRIPTION

The ECM constantly generates 5 V power from the battery voltages supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

A116143E75

When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:
Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned ON. The MIL goes off when the engine is started.


WIRING DIAGRAM


A220560E01


A242728E02


A165789E19


INSPECTION PROCEDURE

1.CHECK MIL
  1. Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch to ON.

    OK:
    MIL lights up



NG
Go to step 2
OK

SYSTEM OK 

2.CHECK COMMUNICATION BETWEEN TECHSTREAM AND ECM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and Techstream ON.

  1. Check the communication between the Techstream and ECM.
    Result 
    Result
    Proceed to
    Communication is possible
    A
    Communication is not possible
    B



A
GO TO MIL CIRCUIT (Click here)
B


3.CHECK MIL (THROTTLE POSITION SENSOR)
  1. Disconnect the D4 throttle body connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.
    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B



A
REPLACE THROTTLE BODY ASSEMBLY (Click here)
B


4.CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR)
  1. Disconnect the A17 accelerator pedal position sensor connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.
    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B



A
REPLACE ACCELERATOR PEDAL POSITION SENSOR (Click here)
B


5.CHECK MIL (CANISTER PUMP MODULE)


    A179928
  1. Disconnect the O24 canister pump module connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.
    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B



A
REPLACE CANISTER PUMP MODULE (Click here)
B


6.CHECK MIL (AIR SWITCHING VALVE for Bank 1)
  1. Disconnect the D37 air switching valve connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.
    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B



A
REPLACE AIR SWITCHING VALVE (Click here)
B


7.CHECK MIL (AIR SWITCHING VALVE for Bank 2)
  1. Disconnect the D38 air switching valve connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.
    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B



A
REPLACE AIR SWITCHING VALVE (Click here)
B


8.CHECK MIL (POWER STEERING OIL PRESSURE SENSOR)
  1. Disconnect the D30 power steering oil pressure sensor connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.
    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B



A
REPLACE POWER STEERING OIL PRESSURE SENSOR (Click here)
B


9.CHECK MIL (CAMSHAFT POSITION SENSOR)
  1. Disconnect the D2 camshaft position sensor connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.
    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B



A
REPLACE CAMSHAFT POSITION SENSOR (Click here)
B


10.CHECK MIL (CRANKSHAFT POSITION SENSOR)
  1. Disconnect the D1 crankshaft position sensor connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.
    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B



A
REPLACE CRANKSHAFT POSITION SENSOR (Click here)
B


11.CHECK MIL (VVT SENSOR for Intake Side of Bank 1)
  1. Disconnect the D22 VVT sensor (for Intake Side of Bank 1) connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.
    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B



A
REPLACE VVT SENSOR (for Intake Side of Bank 1) (Click here)
B


12.CHECK MIL (VVT SENSOR for Exhaust Side of Bank 1)
  1. Disconnect the D24 VVT sensor (for Exhaust Side of Bank 1) connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.
    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B



A
REPLACE VVT SENSOR (for Exhaust Side of Bank 1) (Click here)
B


13.CHECK MIL (VVT SENSOR for Intake Side of Bank 2)
  1. Disconnect the D23 VVT sensor (for Intake Side of Bank 2) connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.
    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B



A
REPLACE VVT SENSOR (for Intake Side of Bank 2) (Click here)
B


14.CHECK MIL (VVT SENSOR for Exhaust Side of Bank 2)
  1. Disconnect the D25 VVT sensor (for Exhaust Side of Bank 2) connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.
    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B



A
REPLACE VVT SENSOR (for Exhaust Side of Bank 2) (Click here)
B


15.CHECK HARNESS AND CONNECTOR
  1. Disconnect the D4 throttle body connector.

  1. Disconnect the A17 accelerator pedal position sensor connector.

  1. Disconnect the O24 canister pump module connector.

  1. Disconnect the D37 air switching valve connector.

  1. Disconnect the D38 air switching valve connector.

  1. Disconnect the D30 power steering oil pressure sensor connector.

  1. Disconnect the D2 camshaft position sensor connector.

  1. Disconnect the D1 crankshaft position sensor connector.

  1. Disconnect the D22 VVT sensor (for Intake Side of Bank 1) connector.

  1. Disconnect the D24 VVT sensor (for Exhaust Side of Bank 1) connector.

  1. Disconnect the D23 VVT sensor (for Intake Side of Bank 2) connector.

  1. Disconnect the D25 VVT sensor (for Exhaust Side of Bank 2) connector.



    A164740E10
  1. Disconnect the A27 and D56 ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D56-80 (VCTA) - Body ground
    Always
    10 kΩ or higher
    A27-57 (VCPA) - Body ground
    Always
    10 kΩ or higher
    A27-59 (VCP2) - Body ground
    Always
    10 kΩ or higher
    D56-66 (VCV2) - Body ground
    Always
    10 kΩ or higher
    D56-67 (VCV1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)