Home › Suspension › SUSPENSION CONTROL › AIR SUSPENSION SYSTEM

DTC    C1751    Compressor Relay Coil Malfunction

for Preparation Click here


DESCRIPTION

When the "UP" side of the height control switch is pressed, a signal is sent from terminal RC of the suspension control ECU to the AIR SUS relay to turn it on.
As a result, the current flows to the AIR SUS relay coil, closing the relay contact, and then the battery positive voltage is applied to the compressor, which causes the compressed air to raise the vehicle height.

DTC Code
Detection Condition
Trouble Area
C1751
When either of the following is detected:
  1. With the AIR SUS relay inactivated, an open signal of the AIR SUS relay is detected for 1 second or more.
  2. With the AIR SUS relay activated, a short signal of the AIR SUS relay is detected 8 times successively.
  1. Wire harness or connector
  2. AIR SUS relay
  3. Suspension control ECU

HINT:
Once the ECU stores DTC C1751 in the memory, the vehicle height control is suspended until a normal signal is input to the ECU from the AIR SUS relay. However, control is resumed if the ignition switch is turned off, then to ON again.


WIRING DIAGRAM


C179531E04


INSPECTION PROCEDURE

NOTICE:
After replacing the suspension control ECU, perform registration (Click here).

HINT:
  1. If DTC C1781 (ECU malfunction) and/or C1782 (power source circuit) is displayed, perform the inspection necessary for DTC C1781 (Click here) and/or C1782 (Click here) first.
  2. If DTC C1781 and the C1782 are output at the same time, perform the inspection necessary for DTC C1782 first.

1.PERFORM ACTIVE TEST USING TECHSTREAM (COMPRESSOR MOTOR RELAY)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON, and turn the Techstream main switch on.

  1. Enter the following menus: Chassis / Air suspension / Active Test.

    Air Suspension 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Compressor Motor Relay
    AIR SUS relay
    ON or OFF
    Operation of solenoid (clicking sound) can be heard

    OK:
    Operation of solenoid (clicking sound) can be heard

    Result 
    Result
    Proceed to
    NG
    A
    OK (When troubleshooting according to the Problem Symptoms Table)
    B
    OK (When troubleshooting according to the DTC Chart)
    C



B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


2.INSPECT SUSPENSION CONTROL RELAY (AIR SUS)
  1. Turn the ignition switch off.



    C149624E15
  1. Remove the AIR SUS relay from the engine relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    When 12 V battery voltage is not applied to terminal 1 and 2
    10 kΩ or higher
    When 12 V battery voltage is applied to terminal 1 and 2
    Below 1 Ω



NG
REPLACE SUSPENSION CONTROL RELAY
OK


3.CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL RELAY - ECU AND BODY GROUND)

C241568E01

  1. Disconnect the O18 ECU connector.

  1. Remove the AIR SUS relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O18-22 (RC) - Relay block AIR SUS relay terminal 1
    Always
    Below 1 Ω
    O18-22 (RC) or Relay block AIR SUS relay terminal 1 - Body ground
    Always
    10 kΩ or higher
    Relay block AIR SUS relay terminal 2 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE SUSPENSION CONTROL ECU (Click here)