Home › Suspension › ALIGNMENT / HANDLING DIAGNOSIS › FRONT WHEEL ALIGNMENT

FRONT WHEEL ALIGNMENT > ADJUSTMENT

for Preparation Click here


NOTICE:
For vehicles equipped with VSC, if the wheel alignment has been adjusted, or if suspension or underbody components have been removed/installed or replaced, be sure to perform the following initialization procedure in order for the system to function normally:
  1. Disconnect the cable from the negative (-) battery terminal for more than 2 seconds.
  2. Reconnect the cable to the negative (-) battery terminal.
  3. Perform zero point calibration of the yaw rate and deceleration sensor, and test mode inspection (Click here).



1. INSPECT TIRE
  1. Check the tires for wear and proper inflation pressure.

    Standard Cold Tire Inflation Pressure:
    Tire Size
    Front
    kPa (kgf/cm2, psi)
    Rear
    kPa (kgf/cm2, psi)
    P275/65R18
    230 (2.3, 33)
    230 (2.3, 33)
    P275/55R20
    210 (2.1, 30)
    230 (2.3, 33)



    R003031
  1. Using a dial indicator, check the tire runout.

    Tire runout:
    3.0 mm (0.118 in.) or less



2. MEASURE VEHICLE HEIGHT

NOTICE:
Before inspecting the wheel alignment, adjust the vehicle height to the specification.



    C180789E02
  1. Press down on the vehicle several times to stabilize the suspension, and then measure the vehicle height.
    Text in Illustration 
    *a
    Front Side
    *b
    Rear Side

    Measuring points:
    A:
    Ground clearance of the front drive shaft center
    B:
    Ground clearance of the front adjusting cam bolt center
    C:
    Ground clearance of the rear drive shaft center
    D:
    Ground clearance of the rear lower arm No. 1 adjusting cam bolt center


    Standard Vehicle Height (Unloaded Vehicle):

    Vehicle Model
    Tire Size
    Front A - B
    Rear C - D
    UPK60L-GKTSKA
    P275/65R18 8JJ
    106.2 mm (4.18 in.)
    29.3 mm (1.15 in.)
    P275/55R20 8JJ
    106.2 mm (4.18 in.)
    29.3 mm (1.15 in.)
    UPK60L-GKTLKA
    P275/65R18 8JJ
    106.1 mm (4.18 in.)
    30.0 mm (1.18 in.)
    P275/55R20 8JJ
    106.1 mm (4.18 in.)
    30.0 mm (1.18 in.)
    UPK65L-GKTSKA
    P275/65R18 8JJ
    101.7 mm (4.00 in.)
    24.8 mm (0.98 in.)
    P275/55R20 8JJ
    101.7 mm (4.00 in.)
    24.8 mm (0.98 in.)
    UPK65L-GKTLKA
    P275/65R18 8JJ
    101.4 mm (3.99 in.)
    25.1 mm (0.99 in.)
    P275/55R20 8JJ
    101.4 mm (3.99 in.)
    25.1 mm (0.99 in.)
    USK60L-GKTSKA
    P275/65R18 8JJ
    108.1 mm (4.26 in.)
    30.3 mm (1.19 in.)
    P275/55R20 8JJ
    108.1 mm (4.26 in.)
    30.3 mm (1.19 in.)
    USK60L-GKTLKA
    P275/65R18 8JJ
    107.6 mm (4.24 in.)
    30.6 mm (1.20 in.)
    P275/55R20 8JJ
    107.6 mm (4.24 in.)
    30.6 mm (1.20 in.)
    USK60L-GKTZKA
    P275/55R20 8JJ
    106.6 mm (4.20 in.)
    39.1 mm (1.54 in.)
    USK65L-GKTSKA
    P275/65R18 8JJ
    101.9 mm (4.01 in.)
    25.2 mm (0.99 in.)
    P275/55R20 8JJ
    101.9 mm (4.01 in.)
    25.2 mm (0.99 in.)
    USK65L-GKTLKA
    P275/65R18 8JJ
    101.7 mm (4.00 in.)
    25.3 mm (1.00 in.)
    P275/55R20 8JJ
    101.7 mm (4.00 in.)
    25.3 mm (1.00 in.)
    USK65L-GKTZKA
    P275/55R20 8JJ
    100.3 mm (3.95 in.)
    34.0 mm (1.34 in.)
    USK65L-GKTSGA
    P275/65R18 8JJ
    101.9 mm (4.01 in.)
    25.2 mm (0.99 in.)
    P275/55R20 8JJ
    101.9 mm (4.01 in.)
    25.2 mm (0.99 in.)
    USK65L-GKTLGA
    P275/65R18 8JJ
    101.7 mm (4.00 in.)
    25.3 mm (1.00 in.)
    P275/55R20 8JJ
    101.7 mm (4.00 in.)
    25.3 mm (1.00 in.)
    USK65L-GKTZGA
    P275/55R20 8JJ
    100.3 mm (3.95 in.)
    34.0 mm (1.34 in.)

    NOTICE:
    The standard value shown here is a value that is used for adjusting the wheel alignment and does not indicate the height of an actual vehicle.



3. INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION


Z003382E25
  1. Install a camber-caster-kingpin gauge or place the front wheels on the center of a wheel alignment tester.
    Text in Illustration 
    *1
    Wheel Alignment Tester
    *2
    Gauge

  1. Inspect the camber, caster and steering axis inclination.

    Standard Camber, Caster, Steering Axis Inclination (Unloaded Vehicle):

    Vehicle Model
    Tire Size
    Camber Inclination
    Caster Inclination
    Steering Axis Inclination
    UPK60L-GKTSKA
    P275/65R18 8JJ
    -0°08' +/-45'
    (-0.13° +/-0.75°)
    3°44' +/-45'
    (3.74° +/-0.75°)
    13°08' +/-45'
    (13.14° +/-0.75°)
    P275/55R20 8JJ
    -0°08' +/-45'
    (-0.13° +/-0.75°)
    3°44' +/-45'
    (3.73° +/-0.75°)
    13°08' +/-45'
    (13.14° +/-0.75°)
    UPK60L-GKTLKA
    P275/65R18 8JJ
    -0°08' +/-45'
    (-0.13° +/-0.75°)
    3°45' +/-45'
    (3.75° +/-0.75°)
    13°08' +/-45'
    (13.14° +/-0.75°)
    P275/55R20 8JJ
    -0°08' +/-45'
    (-0.13° +/-0.75°)
    3°45' +/-45'
    (3.75° +/-0.75°)
    13°08' +/-45'
    (13.14° +/-0.75°)
    UPK65L-GKTSKA
    P275/65R18 8JJ
    -0°01' +/-45'
    (-0.01° +/-0.75°)
    3°38' +/-45'
    (3.63° +/-0.75°)
    13°03' +/-45'
    (13.05° +/-0.75°)
    P275/55R20 8JJ
    -0°01' +/-45'
    (-0.01° +/-0.75°)
    3°35' +/-45'
    (3.58° +/-0.75°)
    13°03' +/-45'
    (13.05° +/-0.75°)
    UPK65L-GKTLKA
    P275/65R18 8JJ
    -0°01' +/-45'
    (-0.01° +/-0.75°)
    3°38' +/-45'
    (3.64° +/-0.75°)
    13°02' +/-45'
    (13.04° +/-0.75°)
    P275/55R20 8JJ
    -0°01' +/-45'
    (-0.01° +/-0.75°)
    3°35' +/-45'
    (3.59° +/-0.75°)
    13°02' +/-45'
    (13.04° +/-0.75°)
    USK60L-GKTSKA
    P275/65R18 8JJ
    -0°10' +/-45'
    (-0.17° +/-0.75°)
    3°46' +/-45'
    (3.76° +/-0.75°)
    13°11' +/-45'
    (13.19° +/-0.75°)
    P275/55R20 8JJ
    -0°10' +/-45'
    (-0.17° +/-0.75°)
    3°46' +/-45'
    (3.76° +/-0.75°)
    13°11' +/-45'
    (13.19° +/-0.75°)
    USK60L-GKTLKA
    P275/65R18 8JJ
    -0°10' +/-45'
    (-0.16° +/-0.75°)
    3°46' +/-45'
    (3.77° +/-0.75°)
    13°11' +/-45'
    (13.18° +/-0.75°)
    P275/55R20 8JJ
    -0°10' +/-45'
    (-0.16° +/-0.75°)
    3°46' +/-45'
    (3.77° +/-0.75°)
    13°11' +/-45'
    (13.18° +/-0.75°)
    USK60L-GKTZKA
    P275/55R20 8JJ
    -0°09' +/-45'
    (-0.15° +/-0.75°)
    3°56' +/-45'
    (3.94° +/-0.75°)
    13°10' +/-45'
    (13.17° +/-0.75°)
    USK65L-GKTSKA
    P275/65R18 8JJ
    -0°01' +/-45'
    (-0.02° +/-0.75°)
    3°38' +/-45'
    (3.64° +/-0.75°)
    13°03' +/-45'
    (13.05° +/-0.75°)
    P275/55R20 8JJ
    -0°01' +/-45'
    (-0.02° +/-0.75°)
    3°35' +/-45'
    (3.59° +/-0.75°)
    13°03' +/-45'
    (13.05° +/-0.75°)
    USK65L-GKTLKA
    P275/65R18 8JJ
    -0°01' +/-45'
    (-0.01° +/-0.75°)
    3°39' +/-45'
    (3.65° +/-0.75°)
    13°03' +/-45'
    (13.05° +/-0.75°)
    P275/55R20 8JJ
    -0°01' +/-45'
    (-0.01° +/-0.75°)
    3°35' +/-45'
    (3.59° +/-0.75°)
    13°03' +/-45'
    (13.05° +/-0.75°)
    USK65L-GKTZKA
    P275/55R20 8JJ
    0°00' +/-45'
    (0.00° +/-0.75°)
    3°46' +/-45'
    (3.76° +/-0.75°)
    13°02' +/-45'
    (13.03° +/-0.75°)
    USK65L-GKTSGA
    P275/65R18 8JJ
    -0°01' +/-45'
    (-0.02° +/-0.75°)
    3°38' +/-45'
    (3.64° +/-0.75°)
    13°03' +/-45'
    (13.05° +/-0.75°)
    P275/55R20 8JJ
    -0°01' +/-45'
    (-0.02° +/-0.75°)
    3°35' +/-45'
    (3.59° +/-0.75°)
    13°03' +/-45'
    (13.05° +/-0.75°)
    USK65L-GKTLGA
    P275/65R18 8JJ
    -0°01' +/-45'
    (-0.01° +/-0.75°)
    3°39' +/-45'
    (3.65° +/-0.75°)
    13°03' +/-45'
    (13.05° +/-0.75°)
    P275/55R20 8JJ
    -0°01' +/-45'
    (-0.01° +/-0.75°)
    3°35' +/-45'
    (3.59° +/-0.75°)
    13°03' +/-45'
    (13.05° +/-0.75°)
    USK65L-GKTZGA
    P275/55R20 8JJ
    0°00' +/-45'
    (0.00° +/-0.75°)
    3°46' +/-45'
    (3.76° +/-0.75°)
    13°02' +/-45'
    (13.03° +/-0.75°)



4. ADJUST CAMBER AND CASTER

HINT:
After the camber has been adjusted, inspect the toe-in.

  1. Loosen the toe adjusting cam bolt and camber adjusting cam nut.



  1. Turn the toe adjusting cam and camber adjusting cam in both directions, and adjust the camber and caster to the center value.

    HINT:
    The camber and caster should be as close as possible to the center value.



    C183664E02


    Text in Illustration 
    *1
    Front Adjusting Cam LH
    *2
    Front Adjusting Cam RH
    *3
    Rear Adjusting Cam LH
    *4
    Rear Adjusting Cam RH
    *a
    Front of the Vehicle
    -
    -



    C183666E02
  1. Read the adjustment chart (example).

    1. Find the wheel alignment standard value applicable for the particular model.

    2. Mark the standard value on the adjustment chart.

      Standard Value (Reference):
      Camber
      Caster
      0°03' (0.05°)
      4°07' (4.12°)

    3. Mark the alignment value measured when the vehicle is unloaded on the adjustment chart.

      Measured Value (Reference):
      Camber
      Caster
      0°20' (0.33°)
      4°00' (4.00°)



    4. As shown in the chart, read the distance from the marked point to 0, and adjust the front and/ or rear adjusting cams accordingly.

      Amount to Turn Adjusting Cams (by Gradation):
      Front Adjusting Cam
      Rear Adjusting Cam
      +1.5
      +2.0



      C183665E02



5. INSPECT TOE-IN


A166181E11
  1. Bounce the vehicle up and down at the corners to stabilize the suspension, and then inspect the toe-in.
    Text in Illustration 
    *a
    Front of the Vehicle

    Standard Toe-in (Unloaded Vehicle):

    Vehicle Model
    Tire Size
    B - A
    UPK60L-GKTSKA
    P275/65R18 8JJ
    2.64 mm (0.1039 in.)
    P275/55R20 8JJ
    2.64 mm (0.1039 in.)
    UPK60L-GKTLKA
    P275/65R18 8JJ
    2.64 mm (0.1039 in.)
    P275/55R20 8JJ
    2.64 mm (0.1039 in.)
    UPK65L-GKTSKA
    P275/65R18 8JJ
    2.37 mm (0.0933 in.)
    P275/55R20 8JJ
    2.37 mm (0.0933 in.)
    UPK65L-GKTLKA
    P275/65R18 8JJ
    2.43 mm (0.0956 in.)
    P275/55R20 8JJ
    2.43 mm (0.0956 in.)
    USK60L-GKTSKA
    P275/65R18 8JJ
    2.15 mm (0.0847 in.)
    P275/55R20 8JJ
    2.15 mm (0.0847 in.)
    USK60L-GKTLKA
    P275/65R18 8JJ
    2.27 mm (0.0894 in.)
    P275/55R20 8JJ
    2.27 mm (0.0894 in.)
    USK60L-GKTZKA
    P275/55R20 8JJ
    2.36 mm (0.0929 in.)
    USK65L-GKTSKA
    P275/65R18 8JJ
    2.31 mm (0.0909 in.)
    P275/55R20 8JJ
    2.31 mm (0.0909 in.)
    USK65L-GKTLKA
    P275/65R18 8JJ
    2.36 mm (0.0929 in.)
    P275/55R20 8JJ
    2.36 mm (0.0929 in.)
    USK65L-GKTZKA
    P275/55R20 8JJ
    2.53 mm (0.0996 in.)
    USK65L-GKTSGA
    P275/65R18 8JJ
    2.31 mm (0.0909 in.)
    P275/55R20 8JJ
    2.31 mm (0.0909 in.)
    USK65L-GKTLGA
    P275/65R18 8JJ
    2.36 mm (0.0929 in.)
    P275/55R20 8JJ
    2.36 mm (0.0929 in.)
    USK65L-GKTZGA
    P275/55R20 8JJ
    2.53 mm (0.0996 in.)

    1. If the toe-in is not as specified, adjust it at the rack ends.



6. ADJUST TOE-IN
  1. Release the rack boot set clips.

  1. Loosen the tie rod end lock nuts.

  1. Turn the right and left rack ends by an equal amount to adjust the toe-in to the center value.



    C159783E02
  1. Check that the lengths of the right and left rack ends are approximately the same.
    Text in Illustration 
    *1
    Lock Nut
    *a
    Length

    Standard difference:
    0 +/-1 mm (0 +/-0.0394 in.)

  1. Tighten the tie rod end lock nuts.

    Torque:
    82 N*m{ 836 kgf*cm , 61 ft.*lbf }

  1. Attach the clips to the boots.

    HINT:
    Make sure that the boots are not twisted.



7. INSPECT WHEEL ANGLE


    C132439E14
  1. Turn the steering wheel to the left and right to the full lock positions and measure the turning angle.
    Text in Illustration 
    *a
    Inside
    *b
    Outside
    *c
    Front of the Vehicle

    Standard Wheel Angle (Unloaded Vehicle):

    Vehicle Model
    Tire Size
    Inside Wheel Angle
    Outside Wheel Angle (Reference)
    UPK60L-GKTSKA
    P275/65R18 8JJ
    -41°01' (-41.02°)
    36°25' (36.42°)
    P275/55R20 8JJ
    -41°01' (-41.02°)
    36°25' (36.42°)
    UPK60L-GKTLKA
    P275/65R18 8JJ
    -41°01' (-41.02°)
    36°25' (36.42°)
    P275/55R20 8JJ
    -41°01' (-41.02°)
    36°25' (36.42°)
    UPK65L-GKTSKA
    P275/65R18 8JJ
    -41°17' (-41.28°)
    36°25' (36.41°)
    P275/55R20 8JJ
    -41°17' (-41.28°)
    36°25' (36.41°)
    UPK65L-GKTLKA
    P275/65R18 8JJ
    -41°17' (-41.28°)
    36°25' (36.42°)
    P275/55R20 8JJ
    -41°17' (-41.28°)
    36°25' (36.42°)
    USK60L-GKTSKA
    P275/65R18 8JJ
    -40°59' (-40.99°)
    36°22' (36.36°)
    P275/55R20 8JJ
    -40°59' (-40.99°)
    36°22' (36.36°)
    USK60L-GKTLKA
    P275/65R18 8JJ
    -41°00' (-41.00°)
    36°23' (36.38°)
    P275/55R20 8JJ
    -41°00' (-41.00°)
    36°23' (36.38°)
    USK60L-GKTZKA
    P275/55R20 8JJ
    -41°01' (-41.01°)
    36°23' (36.39°)
    USK65L-GKTSKA
    P275/65R18 8JJ
    -41°17' (-41.28°)
    36°24' (36.40°)
    P275/55R20 8JJ
    -41°17' (-41.28°)
    36°24' (36.40°)
    USK65L-GKTLKA
    P275/65R18 8JJ
    -41°17' (-41.28°)
    36°25' (36.41°)
    P275/55R20 8JJ
    -41°17' (-41.28°)
    36°25' (36.41°)
    USK65L-GKTZKA
    P275/55R20 8JJ
    -41°17' (-41.29°)
    36°26' (36.43°)
    USK65L-GKTSGA
    P275/65R18 8JJ
    -41°17' (-41.28°)
    36°24' (36.40°)
    P275/55R20 8JJ
    -41°17' (-41.28°)
    36°24' (36.40°)
    USK65L-GKTLGA
    P275/65R18 8JJ
    -41°17' (-41.28°)
    36°25' (36.41°)
    P275/55R20 8JJ
    -41°17' (-41.28°)
    36°25' (36.41°)
    USK65L-GKTZGA
    P275/55R20 8JJ
    -41°17' (-41.29°)
    36°26' (36.43°)



8. PLACE FRONT WHEELS FACING STRAIGHT AHEAD


9. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



11. PERFORM YAW RATE SENSOR ZERO POINT CALIBRATION
(Click here)


12. CHECK STEERING ANGLE SENSOR ZERO POINT CALIBRATION
(Click here)