Home › Audio/Visual/Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for SD)

NAVIGATION SYSTEM (for SD) > Speaker Circuit

for Preparation Click here


DESCRIPTION

The navigation receiver assembly sends sound signals to the speakers.

WIRING DIAGRAM


E232251E01


INSPECTION PROCEDURE

1.CHECK SPEAKER
  1. Check which speakers are malfunctioning.
    Result 
    Result
    Proceed to
    Malfunction in front speaker area
    A
    Malfunction in rear speaker area
    B



B
Go to step 8
A


2.CHECK FRONT SIDE SPEAKER
  1. Check which speakers are malfunctioning.
    Result 
    Result
    Proceed to
    Malfunction in front No. 2 speaker assembly
    A
    Malfunction in front No. 1 speaker assembly
    B



B
Go to step 5
A


3.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY
  1. Temporarily replace the front No. 2 speaker assembly with a new or normally functioning one (Click here).

  1. Check that the speaker sounds normally.

    OK:
    Malfunction disappears.



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)
  1. Disconnect the I26 navigation receiver assembly connector.

  1. Disconnect the I11*1 and/or I13*2 front No. 2 speaker assembly connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    I26-1 (FR+) - I11-3 (TWR+)
    Always
    Below 1 Ω
    I26-5 (FR-) - I11-4 (TWR-)
    I26-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    I26-5 (FR-) - Body ground
    for LH:
    Tester Connection
    Condition
    Specified Condition
    I26-2 (FL+) - I13-3 (TWL+)
    Always
    Below 1 Ω
    I26-6 (FL-) - I13-4 (TWL-)
    I26-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    I26-6 (FL-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)  

5.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    E192950
  1. Disconnect the L8*1 and/or M10*2 front No. 1 speaker assembly connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    3.2 to 4.8 Ω



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY)
  1. *1: for RH
  2. *2: for LH
  1. Disconnect the I11*1 and/or I13*2 front No. 2 speaker assembly connector.

  1. Disconnect the L8*1 and/or M10*2 front No. 1 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    I11-1 (+) - L8-1
    Always
    Below 1 Ω
    I11-2 (-) - L8-2
    I11-1 (+) - Body ground
    Always
    10 kΩ or higher
    I11-2 (-) - Body ground
    for LH:
    Tester Connection
    Condition
    Specified Condition
    I13-1 (+) - M10-1
    Always
    Below 1 Ω
    I13-2 (-) - M10-2
    I13-1 (+) - Body ground
    Always
    10 kΩ or higher
    I13-2 (-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    E146506E20
  1. Disconnect the I11*1 and/or I13*2 front No. 2 speaker assembly connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    1 (+) - 3 (TWR+)
    Always
    Below 1 Ω
    2 (-) - 4 (TWR-)
    for LH:
    Tester Connection
    Condition
    Specified Condition
    1 (+) - 3 (TWL+)
    Always
    Below 1 Ω
    2 (-) - 4 (TWL-)

    Text in Illustration 
    *A
    for RH
    *B
    for LH



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
OK

REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)  

8.CHECK REAR SIDE SPEAKER
  1. Check which speakers are malfunctioning.
    Result 
    Result
    Proceed to
    Quarter side speaker assembly
    A
    Rear No. 1 speaker assembly
    B



B
Go to step 11
A


9.INSPECT QUARTER SIDE SPEAKER ASSEMBLY
  1. Temporarily replace the quarter side speaker assembly with a new or normally functioning one (Click here).

  1. Check that the speaker sounds normally.

    OK:
    Malfunction disappears.



NG
REPLACE QUARTER SIDE SPEAKER ASSEMBLY (Click here)
OK


10.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - QUARTER SIDE SPEAKER ASSEMBLY)
  1. Disconnect the I27 navigation receiver assembly connector.

  1. Disconnect the O37*1 and/or O31*2 quarter side speaker assembly connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    I27-1 (RR+) - O37-1 (+)
    Always
    Below 1 Ω
    I27-3 (RR-) - O37-2 (-)
    I27-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    I27-3 (RR-) - Body ground
    for LH:
    Tester Connection
    Condition
    Specified Condition
    I27-2 (RL+) - O31-1 (+)
    Always
    Below 1 Ω
    I27-6 (RL-) - O31-2 (-)
    I27-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    I27-6 (RL-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)  

11.INSPECT REAR NO. 1 SPEAKER ASSEMBLY


    E192950
  1. Disconnect the N1*1 and/or N7*2 rear No. 1 speaker assembly connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    3.2 to 4.8 Ω



NG
REPLACE REAR NO. 1 SPEAKER ASSEMBLY (Click here)
OK


12.CHECK HARNESS AND CONNECTOR (QUARTER SIDE SPEAKER ASSEMBLY - REAR NO. 1 SPEAKER ASSEMBLY)
  1. *1: for RH
  2. *2: for LH
  1. Disconnect the O37*1 and/or O31*2 quarter side speaker assembly connector.

  1. Disconnect the N1*1 and/or N7*2 rear No. 1 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    O37-3 (+) - N1-1
    Always
    Below 1 Ω
    O37-4 (-) - N1-2
    O37-3 (+) - Body ground
    Always
    10 kΩ or higher
    O37-4 (-) - Body ground
    for LH:
    Tester Connection
    Condition
    Specified Condition
    O31-3 (+) - N7-1
    Always
    Below 1 Ω
    O31-4 (-) - N7-2
    O31-3 (+) - Body ground
    Always
    10 kΩ or higher
    O31-4 (-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


13.INSPECT QUARTER SIDE SPEAKER ASSEMBLY


    E146506E13
  1. Disconnect the O37*1 and/or O31*2 quarter side speaker assembly connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (+) - 3 (+)
    Always
    Below 1 Ω
    2 (-) - 4 (-)



NG
REPLACE QUARTER SIDE SPEAKER ASSEMBLY (Click here)
OK

REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)