REAR POWER SEAT CONTROL SYSTEM > Fold Seat Switch Circuit |

| 1.CHECK FOLD SEAT CONTROL ECU (FOLD SEAT SWITCH SIGNAL) |
Check the No. 1 fold seat switch signal.
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O34-15 (RTRN) - Body ground | Back door open No. 1 fold seat switch LH OFF | 11 to 14 V |
| Back door open No. 1 fold seat switch LH return | Below 1 V | |
| O34-16 (FOLD) - Body ground | Back door open No. 1 fold seat switch LH OFF | 11 to 14 V |
| Back door open No. 1 fold seat switch LH folding | Below 1 V |
| Tester Connection | Condition | Specified Condition |
| P20-15 (RTRN) - Body ground | Back door open No. 1 fold seat switch RH OFF | 11 to 14 V |
| Back door open No. 1 fold seat switch RH return | Below 1 V | |
| P20-16 (FOLD) - Body ground | Back door open No. 1 fold seat switch RH OFF | 11 to 14 V |
| Back door open No. 1 fold seat switch RH folding | Below 1 V |
Check No. 2 fold seat switch signal.
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O34-10 (FLD2) - Body ground | Rear LH door open No. 2 fold seat switch LH OFF | 11 to 14 V |
| Rear LH door open No. 2 fold seat switch LH folding | Below 1 V | |
| O34-14 (RTN2) - Body ground | Rear LH door open No. 2 fold seat switch LH OFF | 11 to 14 V |
| Rear LH door open No. 2 fold seat switch LH return | Below 1 V |
| Tester Connection | Condition | Specified Condition |
| P20-10 (FLD2) - Body ground | Rear RH door open No. 2 fold seat switch RH OFF | 11 to 14 V |
| Rear RH door open No. 2 fold seat switch RH folding | Below 1 V | |
| P20-14 (RTN2) - Body ground | Rear RH door open No. 2 fold seat switch RH OFF | 11 to 14 V |
| Rear RH door open No. 2 fold seat switch RH return | Below 1 V |
| Result | Proceed to |
| OK | A |
| NG (No. 1 fold seat switch signal) | B |
| NG (No. 2 fold seat switch signal) | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 2.READ VALUE USING TECHSTREAM (BACK DOOR COURTESY SWITCH) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream ON.
Enter the following menus: Body Electrical / Back Door P/W / Data List.
According to the display on the Techstream, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Back Door Courtesy Switch | Back Door Courtesy Switch / ON or OFF | ON: Back door opened OFF: Back door closed | - |
|
| ||||
| OK | |
| 3.INSPECT NO. 1 FOLD SEAT SWITCH |
Remove the No. 1 fold seat switch (Click here).

Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 6 (FOLD) - 4 (E) | No. 1 fold seat switch LH fold | Below 1 Ω |
| No. 1 fold seat switch LH OFF | 10 kΩ or higher | |
| 7 (RTRN) - 4 (E) | No. 1 fold seat switch LH return | Below 1 Ω |
| No. 1 fold seat switch LH OFF | 10 kΩ or higher |
| Tester Connection | Switch Condition | Specified Condition |
| 3 (FOLD) - 5 (E) | No. 1 fold seat switch RH fold | Below 1 Ω |
| No. 1 fold seat switch RH OFF | 10 kΩ or higher | |
| 4 (RTRN) - 5 (E) | No. 1 fold seat switch RH return | Below 1 Ω |
| No. 1 fold seat switch RH OFF | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - NO. 1 FOLD SEAT SWITCH) |
![]() |
Disconnect the O34 or P20 ECU connector.
Disconnect the O27 or O28 switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O34-15 (RTRN) - O27-7 (RTRN) | Always | Below 1 Ω |
| O34-15 (RTRN) - Body ground | Always | 10 kΩ or higher |
| O34-16 (FOLD) - O27-6 (FOLD) | Always | Below 1 Ω |
| O34-16 (FOLD) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| P20-15 (RTRN) - O28-4 (RTRN) | Always | Below 1 Ω |
| P20-15 (RTRN) - Body ground | Always | 10 kΩ or higher |
| P20-16 (FOLD) - O28-3 (FOLD) | Always | Below 1 Ω |
| P20-16 (FOLD) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 5.READ VALUE USING TECHSTREAM (REAR DOOR COURTESY SWITCH) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream ON.
Enter the following menus: Body Electrical / Main Body / Data List.
According to the display on the Techstream, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| RL Door Courtesy SW | Rear door courtesy light switch LH signal / ON or OFF | ON: Rear door courtesy light switch LH ON OFF: Rear door courtesy light switch LH OFF | - |
| RR Door Courtesy SW | Rear door courtesy light switch RH signal / ON or OFF | ON: Rear door courtesy light switch RH ON OFF: Rear door courtesy light switch RH OFF | - |
|
| ||||
| OK | |
| 6.INSPECT NO. 2 FOLD SEAT SWITCH |
Remove the No. 2 fold seat switch (Click here).

Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 6 (FOLD) - 4 (E) | No. 2 fold seat switch LH fold | Below 1 Ω |
| No. 2 fold seat switch LH OFF | 10 kΩ or higher | |
| 7 (RTRN) - 4 (E) | No. 2 fold seat switch LH return | Below 1 Ω |
| No. 2 fold seat switch LH OFF | 10 kΩ or higher |
| Tester Connection | Switch Condition | Specified Condition |
| 3 (FOLD) - 5 (E) | No. 2 fold seat switch RH fold | Below 1 Ω |
| No. 2 fold seat switch RH OFF | 10 kΩ or higher | |
| 4 (RTRN) - 5 (E) | No. 2 fold seat switch RH return | Below 1 Ω |
| No. 2 fold seat switch RH OFF | 10 kΩ or higher |
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - NO. 2 FOLD SEAT SWITCH) |
Disconnect the O34 or P20 ECU connector.
![]() |
Disconnect the O26 or P12 switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O34-10 (FLD2) - O26-6 (FOLD) | Always | Below 1 Ω |
| O34-10 (FLD2) - Body ground | Always | 10 kΩ or higher |
| O34-14 (RTN2) - O26-7 (RTRN) | Always | Below 1 Ω |
| O34-14 (RTN2) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| P20-10 (FLD2) - P12-3 (FOLD) | Always | Below 1 Ω |
| P20-10 (FLD2) - Body ground | Always | 10 kΩ or higher |
| P20-14 (RTN2) - P12-4 (RTRN) | Always | Below 1 Ω |
| P20-14 (RTN2) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||