Home › Vehicle Interior › SEAT › REAR POWER SEAT CONTROL SYSTEM

REAR POWER SEAT CONTROL SYSTEM > Reclining Motor Circuit

for Preparation Click here


DESCRIPTION

The fold seat control ECU receives switch operation signals from the No. 1 and No. 2 fold seat switch and rear power seat switch, and activates the power seat motors.

WIRING DIAGRAM


B193759E01


INSPECTION PROCEDURE

1.CHECK POWER SEAT MOTOR (RECLINING MOTOR VOLTAGE)


    B193761E01
  1. Disconnect the a1 and a3 or Y1 and Y3 connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    LH Side 
    Tester Connection
    Condition
    Specified Condition
    a1-1 (FWD) - Body ground
    Ignition switch ON
    Rear power seat switch LH forward
    11 to 14 V
    a1-2 (BACK) - Body ground
    Ignition switch ON
    Rear power seat switch LH backward
    11 to 14 V
    a3-1 (FWD) - Body ground
    Ignition switch ON
    Rear power seat switch LH forward
    11 to 14 V
    a3-2 (BACK) - Body ground
    Ignition switch ON
    Rear power seat switch LH backward
    11 to 14 V
    RH Side 
    Tester Connection
    Condition
    Specified Condition
    Y1-1 (FWD) - Body ground
    Ignition switch ON
    Rear power seat switch RH forward
    11 to 14 V
    Y1-2 (BACK) - Body ground
    Ignition switch ON
    Rear power seat switch RH backward
    11 to 14 V
    Y3-1 (FWD) - Body ground
    Ignition switch ON
    Rear power seat switch RH forward
    11 to 14 V
    Y3-2 (BACK) - Body ground
    Ignition switch ON
    Rear power seat switch RH backward
    11 to 14 V



NG
Go to step 3
OK


2.INSPECT POWER SEAT MOTOR (RECLINING MOTOR)


    B194065E01
  1. Remove the power seat motors (reclining motor) (Click here).

  1. Check the operation of the No. 1 reclining motor.

    1. Check if the seat moves smoothly when the battery is connected to the reclining motor connector terminals.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 1
      Battery negative (-) → 2
      Motor gear rotates clockwise
      Battery positive (+) → 2
      Battery negative (-) → 1
      Motor rear rotates counterclockwise



    B194064E01
  1. Check the operation of the No. 2 reclining motor.

    1. Check if the seat moves smoothly when the battery is connected to the reclining motor connector terminals.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 1
      Battery negative (-) → 2
      Motor gear rotates clockwise
      Battery positive (+) → 2
      Battery negative (-) → 1
      Motor rear rotates counterclockwise



NG
REPLACE POWER SEAT MOTOR (Click here)
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE 

3.CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - RECLINING MOTOR)


    B193760E01
  1. Disconnect the O33 or P19 ECU connector.

  1. Disconnect the a1 or Y1 motor connector.

  1. Disconnect the a3 or Y3 motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    LH Side 
    Tester Connection
    Condition
    Specified Condition
    O33-1 (FLD+) - a3-1 (FWD)
    Always
    Below 1 Ω
    O33-1 (FLD+) - Body ground
    Always
    10 kΩ or higher
    O33-2 (RCL+) - a1-1 (FWD)
    Always
    Below 1 Ω
    O33-2 (RCL+) - Body ground
    Always
    10 kΩ or higher
    O33-5 (FLD-) - a3-2 (BACK)
    Always
    Below 1 Ω
    O33-5 (FLD-) - Body ground
    Always
    10 kΩ or higher
    O33-6 (RCL-) - a1-2 (BACK)
    Always
    Below 1 Ω
    O33-6 (RCL-) - Body ground
    Always
    10 kΩ or higher
    RH Side 
    Tester Connection
    Condition
    Specified Condition
    P19-1 (FLD+) - Y3-1 (FWD)
    Always
    Below 1 Ω
    P19-1 (FLD+) - Body ground
    Always
    10 kΩ or higher
    P19-2 (RCL+) - Y1-1 (FWD)
    Always
    Below 1 Ω
    P19-2 (RCL+) - Body ground
    Always
    10 kΩ or higher
    P19-5 (FLD-) - Y3-2 (BACK)
    Always
    Below 1 Ω
    P19-5 (FLD-) - Body ground
    Always
    10 kΩ or higher
    P19-6 (RCL-) - Y1-2 (BACK)
    Always
    Below 1 Ω
    P19-6 (RCL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FOLD SEAT CONTROL ECU (Click here)