Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF HOUSING

SLIDING ROOF HOUSING > INSTALLATION

for Preparation Click here



1. INSTALL SLIDING ROOF HOUSING SUB-ASSEMBLY


  1. for Type A:



    1. Temporarily install the housing with the 10 bolts (vehicle body side) and 6 nuts.


      B191414

    2. Tighten the 6 nuts.

      Torque:
      5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    3. Tighten the 10 bolts.

      Torque:
      5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



  1. for Type B:



    1. Temporarily install the housing with the 10 bolts (vehicle body side) and 6 nuts.


      B191414E01


      Text in Illustration 
      *1
      Bolt A
      *2
      Bolt B

    2. Tighten the 6 nuts.

      Torque:
      5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    3. Tighten the 10 bolts.

      Torque:
      Bolt A:
      8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

      Torque:
      Bolt B:
      5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



    B262063E01
  1. Connect the 4 sliding roof drain hoses.
    Text in Illustration 
    *a
    Front Side
    *b
    Outer Side
    V100136
    Front

    HINT:
    Install the hose so that the direction of the clip is as indicated in the illustration.



2. INSTALL SLIDING ROOF WEATHERSTRIP


    B170258E02
  1. Install the sliding roof weatherstrip as described below.
    Text in Illustration 
    *a
    Cutout
    *b
    Correct
    *c
    Incorrect
    V100136
    Rear Side

    1. Engage each corner of the weatherstrip so that each weatherstrip mark is aligned with the sliding roof glass center mark. After attaching the entire weatherstrip, check that all weatherstrip marks are within the sliding roof glass end marks.

    2. Make sure that the weatherstrip cutout is toward the rear side of the vehicle and centered.

    3. Make sure that the weatherstrip is securely installed as shown in the illustration.



3. INSTALL SLIDING ROOF GLASS SUB-ASSEMBLY


    B191413
  1. Using a T25 "TORX" socket wrench, temporarily install the glass with the 4 bolts.



  1. Perform a level check.


    B170255E02


    Text in Illustration 
    *a
    Even
    -
    -

    1. Check the difference in the level between the roof panel and the upper surface of the weatherstrip labeled "a" when the sliding roof glass is fully closed.

      Standard:
      Area
      Measurement
      A - A
      0 +/-1.5 mm (0 +/-0.0591 in.)
      B - B
      C - C
      D - D

      HINT:
      "+" represents the condition that the glass is above the panel level. "-" represents the condition that the glass is below the panel level.

    2. Perform a gap check.
      Check the gap between the roof panel and roof glass.

      NOTICE:
      The gap must be even all around.



    B191413
  1. Tighten the 2 bolts.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



4. CHECK FOR WATER LEAK
  1. After adjusting the sliding roof glass sub-assembly, check for water leaks.

  1. If there are any leaks, readjust the sliding roof glass sub-assembly.



5. INSTALL SLIDING ROOF SIDE GARNISH RH


    B231299
  1. Attach the 6 claws to install the sliding roof side garnish.



6. INSTALL SLIDING ROOF SIDE GARNISH LH

HINT:
Use the same procedure for the RH side and LH side.



7. INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY RH
  1. Install the curtain shield airbag .



8. INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY LH

HINT:
Use the same procedure for the RH side and LH side.



9. INSTALL ROOF HEADLINING ASSEMBLY
  1. Install the roof headlining (Click here).



10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



11. INSPECT SRS WARNING LIGHT
(Click here)