DTC C1715 Front Acceleration Sensor RH Malfunction |
DTC C1716 Front Acceleration Sensor LH Malfunction |
DTC C1717 Rear Acceleration Sensor Malfunction |
DTC C1796 Front Acceleration Sensor RH Malfunction (Test Mode DTC) |
DTC C1797 Front Acceleration Sensor LH Malfunction (Test Mode DTC) |
DTC C1798 Rear Acceleration Sensor Malfunction (Test Mode DTC) |
| DTC Code | Detection Condition | Trouble Area |
| C1715 | With the ignition switch ON, a voltage of 4.7 V or more, or 0.3 V or less at front acceleration sensor RH is detected for 1 second. |
|
| C1716 | With the ignition switch ON, a voltage of 4.7 V or more, or 0.3 V or less at front acceleration sensor LH is detected for 1 second. |
|
| C1717 | With the ignition switch ON, a voltage of 4.7 V or more, or 0.3 V or less at rear acceleration sensor is detected for 1 second. |
|
| C1796 | On level surface, G sensor input is +/- 1.96 m/s2 or more for 1 second or more. |
|
| C1797 | On level surface, G sensor input is +/- 1.96 m/s2 or more for 1 second or more. |
|
| C1798 | On level surface, G sensor input is +/- 1.96 m/s2 or more for 1 second or more. |
|

| 1.READ VALUE USING TECHSTREAM (G SENSOR) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON, and turn the Techstream main switch on.
Enter the following menus: Chassis / Air suspension / Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| (Up & Down) G Sensor FR | G (up & down) front acceleration sensor RH reading / min.: -1045.29 m/s2 max.: 1045.26 m/s2 | 0 +/- 0.98 m/s2 at still condition | Reading changes when vehicle (FR) is bounced |
| (Up & Down) G Sensor FL | G (up & down) front acceleration sensor LH reading / min.: -1045.29 m/s2 max.: 1045.26 m/s2 | 0 +/- 0.98 m/s2 at still condition | Reading changes when vehicle (FL) is bounced |
| (Up & Down) G Sensor Rear | G (up & down) rear acceleration sensor reading / min.: -1045.29 m/s2 max.: 1045.26 m/s2 | 0 +/- 0.98 m/s2 at still condition | Reading changes when vehicle (rear) is bounced |
|
| ||||
| OK | ||
| ||
| 2.INSPECT ACCELERATION SENSOR (FRONT LH OR RH) |
Turn the ignition switch off.
![]() |
Check the acceleration sensor RH: (C1715, C1796).
Remove the acceleration sensor RH (Click here).
Connect 3 dry cell batteries of 1.5 V in series.
Connect the positive (+) end of the batteries to terminal 3 (SHB) of the acceleration sensor and the negative (-) end of the batteries to terminal 2 (SHG). Then measure the voltage between terminal 1 (SGFL) and terminal 2 (SHG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Sensor Condition | Specified Condition |
| 1 (SGFL) - 2 (SHG) | Sensor stationary | Approx. 2.0 to 2.5 V |
| Sensor is tilted | Changes between approx. 0.9 to 2.3 V |
![]() |
Check the acceleration sensor LH: (C1716, C1797).
Remove the acceleration sensor LH (Click here).
Connect 3 dry cell batteries of 1.5 V in series.
Connect the positive (+) end of the batteries to terminal 3 (SGV) of the acceleration sensor and the negative (-) end of the batteries to terminal 2 (SGND). Then measure the voltage between terminal 1 (SGRR) and terminal 2 (SGND).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Sensor Condition | Specified Condition |
| 1 (SGRR) - 2 (SGND) | Sensor stationary | Approx. 2.0 to 2.5 V |
| Sensor is tilted | Changes between approx. 0.9 to 2.3 V |
| Result | Proceed to |
| OK | A |
| NG (Front acceleration sensor RH) | B |
| NG (Front acceleration sensor LH) | C |
|
| ||||
|
| ||||
| A | |
| 3.CHECK HARNESS AND CONNECTOR (FRONT ACCELERATION SENSOR - ECU AND BODY GROUND) |
![]() |
Check the acceleration sensor RH: (C1715, C1796).
Disconnect the O17 ECU connector.
Disconnect the H74 sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| H74-1 (SGFL) - O17-18 (SGFR) | Always | Below 1 Ω |
| H74-2 (SHG) - O17-10 (SGR) | Always | Below 1 Ω |
| H74-3 (SHB) - O17-9 (SBR) | Always | Below 1 Ω |
| H74-1 (SGFL) or O17-18 (SGFR) - Body ground | Always | 10 kΩ or higher |
| H74-2 (SHG) or O17-10 (SGR) - Body ground | Always | 10 kΩ or higher |
| H74-3 (SHB) or O17-9 (SBR) - Body ground | Always | 10 kΩ or higher |
![]() |
Check the acceleration sensor LH: (C1716, C1797).
Disconnect the O16 ECU connector.
Disconnect the H75 sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| H75-1 (SGRR) - O16-26 (SGRR) | Always | Below 1 Ω |
| H75-2 (SGND) - O16-16 (SGR3) | Always | Below 1 Ω |
| H75-3 (SGV) - O16-17 (SBR3) | Always | Below 1 Ω |
| H75-1 (SGRR) or O16-26 (SGRR) - Body ground | Always | 10 kΩ or higher |
| H75-2 (SGND) or O16-16 (SGR3) - Body ground | Always | 10 kΩ or higher |
| H75-3 (SGV) or O16-17 (SBR3) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||