DTC C1207/37 Malfunction in Park / Neutral Position Switch |
| DTC Code | DTC Detection Condition | Trouble Area |
| C1207/37 | When all conditions below are met:
|
|

| 1.CHECK CAN COMMUNICATION SYSTEM |
Check if the CAN communication system DTC is output (Click here).
| Result | Proceed to |
| DTC is not output | A |
| DTC is output | B |
|
| ||||
| A | |
| 2.INSPECT PARK / NEUTRAL POSITION SWITCH ASSEMBLY |
![]() |
Disconnect the D21 switch connector.
Measure the resistance of the park/neutral position switch when the shift lever is moved to each position.
| Tester Connection | Condition | Specified Condition |
| 2 (RB) - 6 (PL) | Shift lever in P | Below 1 Ω |
| 2 (RB) - 1 (RL) | Shift lever in R | |
| 2 (RB) - 9 (NL) | Shift lever in N | |
| 2 (RB) - 7 (DL) | Shift lever in D Shift lever in S, "+" and "-" | |
| 4 (B) - 5 (L) | Shift lever in P or N | |
| 2 (RB) - 6 (PL) | Shift lever not in P | 10 kΩ or higher |
| 2 (RB) - 1 (RL) | Shift lever not in R | |
| 2 (RB) - 9 (NL) | Shift lever not in N | |
| 2 (RB) - 7 (DL) | Shift lever not in D Shift lever not in S, "+" and "-" | |
| 4 (B) - 5 (L) | Shift lever not in P and N |
|
| ||||
| OK | |
| 3.CHECK PARK / NEUTRAL POSITION SWITCH ASSEMBLY (POWER SOURCE) |
![]() |
Disconnect the D21 switch connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D21-2 (RB) - Body ground | Ignition switch ON | 11 to 14 V |
| D21-2 (RB) - Body ground | Ignition switch off | Below 1 V |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (PARK / NEUTRAL POSITION SWITCH - ECM) |
![]() |
Disconnect the D21 switch connector.
Disconnect the D56 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D21-4 (B) - D56-120 (NSW) | Always | Below 1 Ω |
| D21-4 (B) or D56-120 (NSW) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (PARK / NEUTRAL POSITION SWITCH - ECM) |
![]() |
Disconnect the D56 ECM connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D56-2 (P) - Body ground | Ignition switch ON Shift lever in P | 11 to 14 V |
| D56-26 (R) - Body ground | Ignition switch ON Shift lever in R | 11 to 14 V* |
| D56-25 (N) - Body ground | Ignition switch ON Shift lever in N | 11 to 14 V |
| D56-27 (D) - Body ground | Ignition switch ON Shift lever in D | |
| D56-2 (P) - Body ground | Ignition switch ON Shift lever not in P | Below 1 V |
| D56-26 (R) - Body ground | Ignition switch ON Shift lever not in R | |
| D56-25 (N) - Body ground | Ignition switch ON Shift lever not in N | |
| D56-27 (D) - Body ground | Ignition switch ON Shift lever not in D |
| Result | Proceed to |
| NG | A |
| OK (for 1UR-FE) | B |
| OK (for 3UR-FE) | C |
| OK (for 3UR-FBE) | D |
|
| ||||
|
| ||||
|
| ||||
| A | ||
| ||