Home › Engine / Hybrid System ยท 1UR-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P0401    Exhaust Gas Recirculation Flow Insufficient Detected

for Preparation Click here


DESCRIPTION

Based on the driving conditions, the ECM regulates the volume of exhaust gas that is recirculated to the engine's combustion chambers and thus lowers the combustion temperature to reduce NOx emissions. The ECM monitors signals such as engine speed, coolant temperature, electric load, and vehicle speed. When the EGR permission conditions are fulfilled, the ECM controls the opening of the EGR valve linearly through signals to the EGR stepper motor.

DTC No.
DTC Detection Condition
Trouble Area
P0401
Change in intake manifold pressure is small when the EGR valve is opened and closed during idle fuel cut operation
(2 trip detection logic)
  1. EGR valve assembly
  2. EGR passages
  3. EGR cooler assembly
  4. Manifold absolute pressure sensor
  5. Air induction system

MONITOR DESCRIPTION

The ECM monitors the pressure inside the intake manifold while opening and closing the EGR valve during fuel cut operation. If there is no change in the manifold absolute pressure sensor value, the ECM interprets this as a malfunction in the EGR valve assembly, illuminates the MIL and stores the DTC (2 trip detection logic).

MONITOR STRATEGY


Related DTC
P0401: EGR valve high flow rate / low flow rate
Required sensors/Components (Main)
EGR valve assembly, manifold absolute pressure sensor
Required sensors/Components (Related)
Engine coolant temperature sensor, vehicle speed sensor
Frequency of operation
Once per driving cycle
Duration
3 seconds
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs are not present
None
Time after engine started
3 seconds or more
Time after engine fuel cut
1 second or more
Engine speed
1050 to 1800 rpm
Vehicle speed
20 km/h (12.5 mph) or more
Engine speed change (per 65 msec.)
-40 to 10 rpm
Time after engine load becomes stable (Brake, lock-up)
More than 1 sec
Shift position
Except "P" or "N" range
Engine coolant temperature
75°C (167°F) or more
Battery voltage
11 V or more
Intake air temperature
-10°C (14°F) or more
Atmospheric pressure
76 kPa (570 mmHg, 22 in.Hg) or more

TYPICAL MALFUNCTION THRESHOLDS


Manifold pressure change
Less than 1.8125 kPa (14 mmHg, 1 in.Hg)
Engine speed
1400 rpm

CONFIRMATION DRIVING PATTERN


A217909E04

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure) (Click here).
  4. Turn the ignition switch off and wait for 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or more [B].

    HINT:
    The A/C switch and all accessory switches should be off and the shift lever should be in P or N.

  7. Drive the vehicle at 60 km/h (37 mph) for 5 minutes or more [C].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  8. Idle the engine for 30 seconds or more [D].
  9. Drive the vehicle at 60 km/h (37 mph) and select the S4 range with the shift lever in S [E].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  10. Perform fuel cut operation for 5 seconds or more with the accelerator pedal fully released [F].

    HINT:
    When "Idle Fuel Cut" in the Data List is ON, fuel cut is operating.

  11. Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor / Exhaust Gas Recirculation/VVT / Current [G].
  12. Check that the Exhaust Gas Recirculation/VVT / Current monitor is Complete.

    HINT:
    If the monitor is Incomplete, perform the driving pattern again.

  13. Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor / Exhaust Gas Recirculation/VVT / Details / EGR FLOW INSUFFICIENCY / Details.
  14. Check the test Details (EGR FLOW INSUFFICIENCY).

    HINT:
    Make sure that the values are between MIN and MAX.

  15. If the monitor is still Incomplete, perform the following procedure.
  16. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
  17. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  18. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  19. Input the DTC: P0401.
  20. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the DTC judgment result is INCOMPLETE or N/A and no pending DTC is output, drive the vehicle again at 60 km/h (37 mph) and select the S4 range with the shift lever in S, perform fuel cut operation for 5 seconds or more with the accelerator pedal fully released, and then check the DTC judgment result.

  21. If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A217943E04


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. By using the Control the EGR Step Position Active Test, the operation of the EGR valve can be checked.
  2. When the engine is idling steadily with the EGR valve fully closed, if the EGR valve is normal and it is opened using the Active Test, the Data List values will change as follows.

    Data List
    Change in Data List when Number of Steps is Increased Using Control the EGR Step Position Active Test
    Engine Speed
    Idle becomes rough
    MAP
    Pressure rises
  3. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P0401)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.
    Result 
    Result
    Proceed to
    DTC P0401 is output
    A
    DTC P0401 and other are output
    B

    HINT:
    If any DTCs other than P0401 are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE EGR VALVE)
  1. Connect the Techstream to the DLC3.

  1. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

    HINT:
    1. When performing the Active Test, make sure the shift lever is in P or N.
    2. The A/C switch and all accessory switches should be off.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.

  1. Confirm the Throttle Idle Position is ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.

    HINT:
    1. Do not leave the EGR valve open for 10 seconds or more during the Active Test.
    2. Be sure to return the EGR valve to step 0 when the Active Test is completed.

    OK:
    MAP and idling condition change in response to EGR step position as follows.


    Standard:

    -
    EGR Step Position (Active Test)
    0 Steps
    0 to 30 Steps
    Idling condition
    Steady idling
    Idling changes from steady to rough idling or engine stall
    MAP
    (Data List)
    -
    MAP value is at least +10 kPa (75 mmHg, 3 in.Hg) higher than when EGR valve is fully closed



NG
Go to step 4
OK


3.INSPECT EGR VALVE
  1. Confirm that there are no deposits on the EGR valve.

  1. Confirm that the EGR valve is closed.

    OK:
    There are no deposits and the valve is closed.



OK
Go to step 5

NG
Go to step 4

4.REPLACE EGR VALVE ASSEMBLY
  1. Replace the EGR valve assembly (Click here).


NEXT


5.CHECK FOR DEPOSIT (EGR VALVE ASSEMBLY TO INTAKE PORT)
A217946
  1. Check for exhaust leaks at each connection point.

  1. Check for cracks, damage and blockage of the pipes between the intake manifold converter and EGR valve assembly.

    HINT:
    This check may require the removal of components.

  1. Check for blockage due to deposits in the EGR valve and pipes.

    OK:
    No deposits.



NG
REPAIR OR REPLACE MALFUNCTIONING PARTS
OK


6.CHECK FOR DEPOSIT (EXHAUST MANIFOLD CONVERTER TO EGR VALVE ASSEMBLY)
A217945
  1. Check for exhaust leaks at each connection point.

  1. Check for cracks, damage and blockage of the pipes between the exhaust manifold converter and EGR valve assembly.

    HINT:
    This check may require the removal of components.

  1. Check for blockage due to deposits in the EGR valve and pipes.

    OK:
    No deposits.



NG
REPAIR OR REPLACE MALFUNCTIONING PARTS
OK


7.INSPECT EGR COOLER
  1. Check for blockage in the EGR cooler.



NG
REPAIR OR REPLACE EGR COOLER (Click here)
OK


8.READ VALUE USING TECHSTREAM (MANIFOLD ABSOLUTE PRESSURE SENSOR)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAP.

  1. Read the MAP value.

    Standard:
    Switch Condition
    Techstream Display
    Ignition switch ON
    80 to 110 kPa (600 to 825 mmHg, 24 to 32 in.Hg)



OK
Go to step 11

NG
Go to step 9

9.CHECK AIR INDUCTION SYSTEM
  1. Check the air induction system for vacuum leaks .

    OK:
    No leaks in air induction system.



NG
REPAIR OR REPLACE AIR INDUCTION SYSTEM (Click here)
OK


10.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
  1. Replace the manifold absolute pressure sensor (Click here).


NEXT


11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTC (Click here).

  1. Turn the ignition switch off and wait for 30 seconds.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or more.

    HINT:
    The A/C switch and all accessory switches should be off.

  1. Drive the vehicle at 60 km/h (37 mph) for 5 minutes or more.

  1. Idle the engine for 30 seconds or more.

  1. Drive the vehicle at 60 km/h (37 mph).

    CAUTION:
    Strictly observe speed limits and traffic laws when performing the confirmation drive pattern.

  1. Perform fuel cut operation for 5 seconds or more with the accelerator pedal fully released.

    HINT:
    If the deceleration was not completed, perform the Confirmation Driving Pattern again.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.

  1. Read the pending DTCs.

  1. If a pending DTC is output, the system is malfunctioning.

    HINT:
    If a pending DTC is not output, perform the following procedure.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P0401.

  1. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit


NEXT

END