Home › Engine / Hybrid System ยท 1UR-FE › INTAKE / EXHAUST › INTAKE MANIFOLD

INTAKE MANIFOLD > REMOVAL

for Preparation Click here



1. DISCHARGE FUEL SYSTEM PRESSURE

CAUTION:
  1. Do not disconnect any part of the fuel system until you have discharged the fuel system pressure.
  2. After discharging the fuel pressure, place a cloth or equivalent over fittings as you separate them to reduce the risk of fuel spray on yourself or in the engine compartment.

  1. Disconnect the cable from the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable some systems need to be initialized after the cable is reconnected (Click here).



    A240791E01
  1. Turn the lock lever and disconnect the connector of the fuel pump ECU.
    Text in Illustration 
    *1
    Lock Lever

  1. Connect the cable to the negative (-) battery terminal.

  1. Start the engine. After the engine has stopped on its own, turn the ignition switch off.

    HINT:
    DTC P0171/0174 (system too lean) may be set.

  1. Crank the engine again, then check that the engine does not start.

  1. Loosen the fuel tank cap, then discharge the pressure in the fuel tank completely.



    A240793E01
  1. Connect the connector of the fuel pump ECU.

  1. Turn the lock lever and secure the connector with the lock lever.
    Text in Illustration 
    *1
    Lock Lever



2. REMOVE EGR VALVE ASSEMBLY
  1. Remove the EGR valve (Click here).



3. REMOVE FRONT WIPER MOTOR AND LINK ASSEMBLY
  1. Remove the front wiper motor and link (Click here).



4. REMOVE COWL TOP OUTER PANEL SUB-ASSEMBLY
  1. Disconnect the washer hose and 2 wire harness clamps.



  1. Remove the 7 bolts and outer panel.


    A215877



5. REMOVE VENTILATION HOSE ASSEMBLY


    A215286
  1. Disconnect the ventilation hose from the ventilation pipe of the cylinder head cover LH and RH.

  1. Remove the bolt and ventilation hose.



6. REMOVE AIR TUBE SUB-ASSEMBLY LH


    A215879
  1. Disconnect the 2 connectors.

  1. Disconnect the water by-pass hose.



    A215282
  1. Disconnect the 2 wire harness clamps and air hose.

  1. Remove the bolt and disconnect the air tube LH from the water inlet housing.



    A215284
  1. Disconnect the vacuum sensor connector and clamp.

  1. Remove the 2 bolts and disconnect the air hose from the air switching valve LH.

  1. Remove the air tube LH.



7. REMOVE INTAKE MANIFOLD


    A215281
  1. Disconnect the No. 4 water by-pass hose.

  1. Disconnect the throttle body connector.

  1. Disconnect the No. 1 ventilation hose.



    A215287
  1. Disconnect the purge VSV connector.

  1. Disconnect the purge line hose from the purge VSV.

  1. Disconnect the vacuum switching valve connector (for ACIS).



    A215288
  1. Disconnect the vacuum hose.



    A215285
  1. Remove the bolt and disconnect the wire harness from the wire harness bracket.

  1. Detach the 3 wire harness clamps from the 3 wire harness brackets.



    A216804
  1. Detach the 4 clamps from the fuel tube.



    A214311
  1. Disconnect the fuel tube from the fuel delivery pipe RH (Click here).



    A214312
  1. Disconnect the fuel tube from the fuel delivery pipe LH (Click here).



    A215289
  1. Remove the 2 nuts, 8 bolts, intake manifold and 2 gaskets.



8. REMOVE FUEL TUBE SUB-ASSEMBLY


    A215303
  1. Remove the bolt and fuel tube from the intake manifold.



9. REMOVE V-BANK COVER BRACKET


    A215290
  1. Remove the 2 bolts and bracket.



10. REMOVE V-BANK COVER PIN


    A215291
  1. Remove the pin from the intake manifold.



11. REMOVE STUD BOLT


    A216133
  1. Using an E5 "TORX" socket wrench, remove the 2 stud bolts.



12. REMOVE VACUUM SWITCHING VALVE ASSEMBLY (for ACIS)


    A164145
  1. Disconnect the 2 vacuum hoses from the vacuum switching valve.

  1. Remove the bolt and vacuum switching valve.



13. REMOVE PURGE VSV


    A215294
  1. Disconnect the purge line hose from the intake manifold.

  1. Remove the bolt and purge VSV.



14. REMOVE UNION TO CONNECTOR TUBE HOSE ASSEMBLY


    A215295
  1. Remove the 2 bolts and detach the hose clamp.

  1. Remove the union to connector tube hose from the intake manifold.

  1. Remove the 2 bolts and 2 wire harness brackets.



15. REMOVE MANIFOLD ABSOLUTE PRESSURE SENSOR
  1. Disconnect the manifold absolute pressure sensor connector.



    A215298
  1. Remove the screw and manifold absolute pressure sensor.



    A215299
  1. Remove the O-ring from the manifold absolute pressure sensor.



16. REMOVE THROTTLE BODY ASSEMBLY


    A215292
  1. Remove the 4 bolts, throttle body and gasket.