Home › Audio/Visual/Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for SD)

DTC    B15C3    Speaker Output Short

for Preparation Click here


DESCRIPTION

This DTC is stored when a malfunction occurs in the speakers.

DTC Code
DTC Detection Condition
Trouble Area
B15C3
A short is detected in the speaker output circuit.
  1. Harness or connector
  2. Speakers
  3. Navigation receiver assembly

WIRING DIAGRAM


E232251E01


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR
  1. Disconnect the connectors from the navigation receiver assembly and speakers.

  1. Measure the resistance between the navigation receiver assembly and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K30-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    K30-5 (FR-) - Body ground
    Always
    10 kΩ or higher
    K30-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    K30-6 (FL-) - Body ground
    Always
    10 kΩ or higher
    K31-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    K31-3 (RR-) - Body ground
    Always
    10 kΩ or higher
    K31-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    K31-6 (RL-) - Body ground
    Always
    10 kΩ or higher

  1. Measure the resistance between each of the front No. 2 speaker assemblies and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I11-1 (+) - Body ground
    Always
    10 kΩ or higher
    I11-2 (-) - Body ground
    Always
    10 kΩ or higher
    I13-1 (+) - Body ground
    Always
    10 kΩ or higher
    I13-2 (-) - Body ground
    Always
    10 kΩ or higher

  1. Measure the resistance between each of the quarter side speaker assemblies and body ground to check for a short circuit in the wire harness.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O31-3 (+) - Body ground
    Always
    10 kΩ or higher
    O31-4 (-) - Body ground
    Always
    10 kΩ or higher
    O37-3 (+) - Body ground
    Always
    10 kΩ or higher
    O37-4 (-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    E192950
  1. Disconnect the L8*1 and/or M10*2 front No. 1 speaker assembly connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    3.2 to 4.8 Ω



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


3.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    E146506E20
  1. Disconnect the I11*1 and/or I13*2 front No. 2 speaker assembly connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    1 (+) - 3 (TWR+)
    Always
    Below 1 Ω
    2 (-) - 4 (TWR-)
    for LH:
    Tester Connection
    Condition
    Specified Condition
    1 (+) - 3 (TWL+)
    Always
    Below 1 Ω
    2 (-) - 4 (TWL-)

    Text in Illustration 
    *A
    for RH
    *B
    for LH



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
OK


4.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY
  1. Temporarily replace the quarter side speaker assembly with a new or normally functioning one (Click here).

  1. Check that the speaker sounds normally.

    OK:
    Malfunction disappears.



NG
Go to step 5
OK

END (FRONT NO. 2 SPEAKER ASSEMBLY WAS DEFECTIVE) 

5.INSPECT REAR NO. 1 SPEAKER ASSEMBLY


    E192950
  1. Disconnect the N1*1 and/or N7*2 rear No. 1 speaker assembly connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    3.2 to 4.8 Ω



NG
REPLACE REAR NO. 1 SPEAKER ASSEMBLY (Click here)
OK


6.INSPECT QUARTER SIDE SPEAKER ASSEMBLY


    E146506E13
  1. Disconnect the O37*1 and/or O31*2 quarter side speaker assembly connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (+) - 3 (+)
    Always
    Below 1 Ω
    2 (-) - 4 (-)



NG
REPLACE QUARTER SIDE SPEAKER ASSEMBLY (Click here)
OK


7.INSPECT QUARTER SIDE SPEAKER ASSEMBLY
  1. Temporarily replace the quarter side speaker assembly with a new or normally functioning one (Click here).

  1. Check that the speaker sounds normally.

    OK:
    Malfunction disappears.



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK

END (QUARTER SIDE SPEAKER ASSEMBLY WAS DEFECTIVE)