Home › Drivetrain ยท AB60E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM

AUTOMATIC TRANSMISSION SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



READ DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the intelligent tester on.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List.

  7. According to the display on the intelligent tester, read the Data List.

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Neutral Position SW Signal
    PNP switch status/
    ON or OFF
    Shift lever is:
    1. In P or N: ON
    2. Not in P or N: OFF
    When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here)

    Stop Light Switch
    Stop light switch status/
    ON or OFF
    Brake pedal is:
    1. Depressed: ON
    2. Released: OFF
    -
    SPD (NT)
    Input shaft speed/
    Min.: 0 rpm
    Max.: 12750 rpm
    Lock-up is:
    1. ON (after warming up engine): Input turbine speed (NT) is equal to engine speed
    2. OFF (idling with shift lever in N): Input turbine speed (NT) is nearly equal to engine speed
    Data is displayed in increments of 50 rpm
    SPD (SP2)
    Output shaft speed/
    Min.: 0 km/h (0 mph)
    Max.: 255 km/h (158 mph)
    Vehicle stopped: 0 km/h (0 mph) (output shaft speed is equal to vehicle speed)
    -
    Shift SW Status (P Range)
    PNP switch status/
    ON or OFF
    Shift lever is:
    1. In P: ON
    2. Not in P: OFF
    When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here)

    Shift SW Status (R Range)
    PNP switch status/
    ON or OFF
    Shift lever is:
    1. In R: ON
    2. Not in R: OFF
    When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here)

    Shift SW Status (N Range)
    PNP switch status/
    ON or OFF
    Shift lever is:
    1. In N: ON
    2. Not in N: OFF
    When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here)

    Sports Shift Up SW
    Sport shift up switch status/
    ON or OFF
    1. ON: Continuously shift to "+" (up-shift)
    2. OFF: Release "+" (up-shift)
    -
    Sports Shift Down SW
    Sport shift down switch status/
    ON or OFF
    1. ON: Continuously shift to "-" (down-shift)
    2. OFF: Release "-" (down-shift)
    -
    Sports Mode Selection SW
    Sport mode select switch status/
    ON or OFF
    Shift lever is:
    1. ON: In S, "+" and "-"
    2. OFF: Not in S, "+" and "-"
    -
    Shift SW Status (D Range)
    PNP switch status/
    ON or OFF
    Shift lever is:
    1. In D, S, "+" and "-": ON
    2. Not in D, S, "+" and "-": OFF
    When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here)

    A/T Oil Temperature 1
    No. 1 ATF temperature sensor value/
    Min.: -40°C (-40°F)
    Max.: 215°C (419°F)
    1. After stall test: Approximately 80°C (176°F)
    2. Equal to ambient temperature while engine is cold
    If value is -40°C (-40°F) or 215°C (419°F), No. 1 ATF temperature sensor circuit is open or shorted
    A/T Oil Temperature 2
    No. 2 ATF temperature sensor value/
    Min.: -40°C (-40°F)
    Max.: 215°C (419°F)
    1. After stall test: Approximately 80°C (176°F)
    2. Equal to ambient temperature while engine is cold
    If value is -40°C (-40°F) or 215°C (419°F), No. 2 ATF temperature sensor circuit is open or shorted
    Lock Up
    Lock-up/
    ON or OFF
    Lock-up is:
    1. Operating: ON
    2. Not operating: OFF
    -
    Lock Up Solenoid Status
    Lock-up solenoid status/
    ON or OFF
    Lock-up solenoid is:
    1. Operating: ON
    2. Not operating: OFF
    -
    Shift Status
    ECM gear shift command/
    1st, 2nd, 3rd, 4th, 5th or 6th
    Shift lever is:
    1. In D: 1st, 2nd, 3rd, 4th, 5th or 6th
    2. In S: 1st, 2nd, 3rd, 4th, 5th or 6th
    -
    SLT Solenoid Status
    Shift solenoid SLT status/
    ON or OFF
    1. Accelerator pedal is depressed: OFF
    2. Accelerator pedal is released: ON
    -
    SLU Solenoid Status
    Shift solenoid SLU status/
    ON or OFF
    Shift solenoid SLU is:
    1. Operating: ON
    2. Not operating: OFF
    -
    AT Fluid
    Flex lock-up judder judgment/
    ON or OFF
    1. ON: Judder judgment occurs
    2. OFF: Judder judgment does not occur
    -


PERFORM ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the intelligent tester on.

  6. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  7. According to the display on the intelligent tester, perform the Active Test.

    Engine and ECT 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Activate the Solenoid (SLU)
    Operate the shift solenoid SLU
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever in P or N
    Activate the Solenoid (SLT)*
    Operate the shift solenoid SLT and raise line pressure
    ON or OFF

    HINT:
    1. OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, ECM commands SLT solenoid to turn OFF)
    2. ON: No action (normal operation)

    [Vehicle Condition]
    1. Vehicle stopped
    2. Engine idling
    Activate the Solenoid (S1)
    Operate the shift solenoid S1
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever in P or N
    Activate the Solenoid (S2)
    Operate the shift solenoid S2
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever in P or N
    Activate the Solenoid (S3)
    Operate the shift solenoid S3
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever in P or N
    Activate the Solenoid (S4)
    Operate the shift solenoid S4
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever in P or N
    Activate the Lock Up
    Control shift solenoid SLU to set automatic transmission to lock-up condition
    ON or OFF
    Possible to check shift solenoid valve SLU operation
    [Vehicle Condition]
    1. Throttle valve opening angle: Less than 35%
    2. Vehicle speed: 60 km/h (36 mph) or more
    Control the Shift Position
    Operate shift solenoid valve and set each shift position by yourself
    1. Press "→" button: Shift up
    2. Press "←" button: Shift down
    Possible to check operation of shift solenoid valves
    [Vehicle Condition]
    50 km/h (30 mph) or less
    Activate the Solenoid (SR)
    Operate the shift solenoid SR
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever in P or N
    Activate the Solenoid (SL1)
    Operate the shift solenoid SL1
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever in P or N
    Activate the Solenoid (SL2)
    Operate the shift solenoid SL2
    ON or OFF
    [Vehicle Condition]
    1. Engine stopped
    2. Shift lever in P or N

    HINT:
    *: Activate the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test (Click here) as well. Please note that the pressure values in the Active Test and Hydraulic Test are different.