Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM

DTC    B1815/54    Short in Front Passenger Side Squib 2nd Step Circuit

DTC    B1816/54    Open in Front Passenger Side Squib 2nd Step Circuit

DTC    B1817/54    Short to GND in Front Passenger Side Squib 2nd Step Circuit

DTC    B1818/54    Short to B+ in Front Passenger Side Squib 2nd Step Circuit

for Preparation Click here


DESCRIPTION

The front passenger side squib 2nd step circuit consists of the center airbag sensor and the front passenger airbag.
The circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the front passenger side squib 2nd step circuit.

DTC Code
Detection Condition
Trouble Area
B1815/54
When one of following conditions is met:
  1. The center airbag sensor receives a line short circuit signal 5 times in the front passenger side squib 2nd step circuit during primary check.
  2. Front passenger side squib 2nd step malfunction
  3. Center airbag sensor malfunction
  1. Instrument panel wire
  2. No. 2 instrument panel wire
  3. Front passenger airbag assembly (Front passenger side squib 2nd step)
  4. Center airbag sensor assembly
B1816/54
When one of following conditions is met:
  1. The center airbag sensor receives an open circuit signal in the front passenger side squib 2nd step circuit for 2 seconds.
  2. Front passenger side squib 2nd step malfunction
  3. Center airbag sensor malfunction
  1. Instrument panel wire
  2. No. 2 instrument panel wire
  3. Front passenger airbag assembly (Front passenger side squib 2nd step)
  4. Center airbag sensor assembly
B1817/54
When one of following conditions is met:
  1. The center airbag sensor receives a short circuit to ground signal in the front passenger side squib 2nd step circuit for 0.5 seconds.
  2. Front passenger side squib 2nd step malfunction
  3. Center airbag sensor malfunction
  1. Instrument panel wire
  2. No. 2 instrument panel wire
  3. Front passenger airbag assembly (Front passenger side squib 2nd step)
  4. Center airbag sensor assembly
B1818/54
When one of following conditions is met:
  1. The center airbag sensor receives a short circuit to B+ signal in the front passenger side squib 2nd step circuit for 0.5 seconds.
  2. Front passenger side squib 2nd step malfunction
  3. Center airbag sensor malfunction
  1. Instrument panel wire
  2. No. 2 instrument panel wire
  3. Front passenger airbag assembly (Front passenger side squib 2nd step)
  4. Center airbag sensor assembly

WIRING DIAGRAM


C146249E49


INSPECTION PROCEDURE

HINT:
  1. Perform the simulation method by selecting "check mode" (signal check) with the intelligent tester (Click here).
  2. After selecting "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on various types of roads (Click here).

1.CHECK CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connector is properly connected to the front passenger airbag.

    OK:
    The connector is properly connected.

    HINT:
    If the connector is not connected securely, reconnect the connector and proceed to the next inspection.

  1. Disconnect the connector from the front passenger airbag.

  1. Check that the No. 2 instrument panel wire connector (on the front passenger airbag side) is not damaged.

    OK:
    The lock button is not disengaged, or the claw of the lock is not deformed or damaged.



NG
REPLACE NO. 2 INSTRUMENT PANEL WIRE
OK


2.CHECK FRONT PASSENGER AIRBAG (FRONT PASSENGER SIDE SQUIB 2ND STEP)
C172904E01
  1. Connect the white wire side of SST (resistance: 2.1 Ω) to connector E (black connector).

    CAUTION:
    Never connect the tester to the front passenger airbag (front passenger side squib 2nd step) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting SST.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1815, B1816, B1817, B1818 or 54 is not output.

    HINT:
    Codes other than DTC B1815, B1816, B1817, B1818 and 54 may be output at this time, but they are not related to this check.



NG
Go to step 3
OK

REPLACE FRONT PASSENGER AIRBAG ASSEMBLY (Click here)  

3.CHECK CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect SST from connector E.

  1. Check that the connector is properly connected to the center airbag sensor assembly.

    OK:
    The connector is properly connected.

    HINT:
    If the connector is not connected securely, reconnect the connector and proceed to the next inspection.

  1. Disconnect the connector from the center airbag sensor assembly.

  1. Check that the terminal of the connector is not damaged.

    OK:
    The terminal is not deformed or damaged.

  1. Check that the short spring for the instrument panel wire connector with the activation prevention mechanism is not deformed or damaged.

    OK:
    The short spring is not deformed or damaged.



NG
REPLACE INSTRUMENT PANEL WIRE
OK


4.CHECK FRONT PASSENGER SIDE SQUIB 2ND STEP CIRCUIT
C172905E02
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    z9-1 (P2+) - Body ground
    Ignition switch ON
    Below 1 V
    z9-2 (P2-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z9-1 (P2+) - z9-2 (P2-)
    Always
    Below 1 Ω

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z9-1 (P2+) - z9-2 (P2-)
    Always
    1 MΩ or higher
    z9-1 (P2+) - Body ground
    Always
    1 MΩ or higher
    z9-2 (P2-) - Body ground
    Always
    1 MΩ or higher



NG
Go to step 6
OK


5.CHECK CENTER AIRBAG SENSOR
C162203E02
  1. Restore the released activation prevention mechanism of connector B to the original condition.

  1. Connect the connectors to the front passenger airbag and the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1815, B1816, B1817, B1818 or 54 is not output.

    HINT:
    Codes other than DTC B1815, B1816, B1817, B1818 and 54 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)  

6.CHECK CONNECTOR
  1. Restore the released activation prevention mechanism of connector B to the original condition.

  1. Check that the connectors that link the instrument panel wire and No. 2 instrument panel wire harness are properly connected.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors that link the instrument panel wire and No. 2 instrument panel wire.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.

  1. Check that the short spring for the No. 2 instrument panel wire connector with the activation prevention mechanism is not deformed or damaged.

    OK:
    The short spring is not deformed or damaged.



NG
REPLACE HARNESS AND CONNECTOR
OK


7.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - NO. 2 INSTRUMENT PANEL WIRE)
C179155E06
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Hz1-3 - Body ground
    Ignition switch ON
    Below 1 V
    Hz1-4 - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Hz1-3 - Hz1-4
    Always
    Below 1 Ω

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Hz1-3 - Hz1-4
    Always
    1 MΩ or higher
    Hz1-3 - Body ground
    Always
    1 MΩ or higher
    Hz1-4 - Body ground
    Always
    1 MΩ or higher



NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE NO. 2 INSTRUMENT PANEL WIRE