DTC B1815/54 Short in Front Passenger Side Squib 2nd Step Circuit |
DTC B1816/54 Open in Front Passenger Side Squib 2nd Step Circuit |
DTC B1817/54 Short to GND in Front Passenger Side Squib 2nd Step Circuit |
DTC B1818/54 Short to B+ in Front Passenger Side Squib 2nd Step Circuit |
| DTC Code | Detection Condition | Trouble Area |
| B1815/54 | When one of following conditions is met:
|
|
| B1816/54 | When one of following conditions is met:
|
|
| B1817/54 | When one of following conditions is met:
|
|
| B1818/54 | When one of following conditions is met:
|
|

| 1.CHECK CONNECTOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connector is properly connected to the front passenger airbag.
Disconnect the connector from the front passenger airbag.
Check that the No. 2 instrument panel wire connector (on the front passenger airbag side) is not damaged.
|
| ||||
| OK | |
| 2.CHECK FRONT PASSENGER AIRBAG (FRONT PASSENGER SIDE SQUIB 2ND STEP) |
![]() |
Connect the white wire side of SST (resistance: 2.1 Ω) to connector E (black connector).
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 3.CHECK CONNECTOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect SST from connector E.
Check that the connector is properly connected to the center airbag sensor assembly.
Disconnect the connector from the center airbag sensor assembly.
Check that the terminal of the connector is not damaged.
Check that the short spring for the instrument panel wire connector with the activation prevention mechanism is not deformed or damaged.
|
| ||||
| OK | |
| 4.CHECK FRONT PASSENGER SIDE SQUIB 2ND STEP CIRCUIT |
![]() |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| z9-1 (P2+) - Body ground | Ignition switch ON | Below 1 V |
| z9-2 (P2-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z9-1 (P2+) - z9-2 (P2-) | Always | Below 1 Ω |
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z9-1 (P2+) - z9-2 (P2-) | Always | 1 MΩ or higher |
| z9-1 (P2+) - Body ground | Always | 1 MΩ or higher |
| z9-2 (P2-) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 5.CHECK CENTER AIRBAG SENSOR |
![]() |
Restore the released activation prevention mechanism of connector B to the original condition.
Connect the connectors to the front passenger airbag and the center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| OK | A |
| NG (w/ Cool Box) | B |
| NG (w/o Cool Box) | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 6.CHECK CONNECTOR |
Restore the released activation prevention mechanism of connector B to the original condition.
Check that the connectors that link the instrument panel wire and No. 2 instrument panel wire harness are properly connected.
Disconnect the connectors that link the instrument panel wire and No. 2 instrument panel wire.
Check that the terminals of the connectors are not damaged.
Check that the short spring for the No. 2 instrument panel wire connector with the activation prevention mechanism is not deformed or damaged.
|
| ||||
| OK | |
| 7.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - NO. 2 INSTRUMENT PANEL WIRE) |
![]() |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| Hz1-3 - Body ground | Ignition switch ON | Below 1 V |
| Hz1-4 - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Hz1-3 - Hz1-4 | Always | Below 1 Ω |
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Hz1-3 - Hz1-4 | Always | 1 MΩ or higher |
| Hz1-3 - Body ground | Always | 1 MΩ or higher |
| Hz1-4 - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | ||
| ||