Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM

DTC    B1788    Rear Occupant Classification Sensor RH Collision Detection

for Preparation Click here


DESCRIPTION

DTC B1788 is stored when the occupant classification ECU receives a collision detection signal, which is sent by the occupant detection sensor rear RH when an accident occurs.
DTC B1788 is also stored when the front seat assembly RH is subjected to a strong impact, even if an actual accident has not occurred.
However, when the occupant classification ECU outputs a collision detection signal, even if the vehicle is not in a collision, DTC B1788 can be cleared by conducting the zero point calibration and sensitivity check.
Therefore, if DTC B1788 is stored, first perform the zero point calibration and sensitivity check.

DTC Code
DTC Detection Condition
Trouble Area
B1788
Either of following conditions is met:
  1. Occupant classification ECU receives collision detection signal, which is sent by occupant detection sensor rear RH when accident occurs
  2. Front seat assembly RH is subjected to strong impact, even if actual accident has not occurred
  1. Front seat assembly RH (Rear occupant detection sensor RH)
  2. Occupant classification ECU

HINT:
  1. When DTC B1650/32 is stored as a result of troubleshooting the airbag system, perform troubleshooting for DTC B1788 of the occupant classification system.
  2. Use the intelligent tester to check for DTCs of the occupant classification ECU, otherwise the DTCs cannot be read.


WIRING DIAGRAM


B151586E22


INSPECTION PROCEDURE

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).
  2. When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).

1.CHECK FOR DTCs
  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the center airbag sensor (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the intelligent tester, check for DTCs of the occupant classification ECU (Click here).

    OK:
    DTC B1788 is not output.

    HINT:
    DTCs other than DTC B1788 may be output at this time, but they are not related to this check.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)  

2.PERFORM ZERO POINT CALIBRATION
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the intelligent tester, perform the zero point calibration (Click here).



NG
Go to step 5
OK


3.PERFORM SENSITIVITY CHECK
  1. Using the intelligent tester, perform the sensitivity check (Click here).

    Standard range:
    27 to 33 kg (59.5 to 72.8 lb)



NG
Go to step 5
OK


4.CHECK FOR DTCs
  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the center airbag sensor (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the intelligent tester, check for DTCs of the occupant classification ECU (Click here).

    OK:
    DTC B1788 is not output.

    HINT:
    DTCs other than DTC B1788 may be output at this time, but they are not related to this check.



NG
Go to step 5
OK

END 

5.REPLACE FRONT SEAT ASSEMBLY RH
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Replace the front seat frame with adjuster RH.

    1. for Manual Seat (Click here)
    2. for Power Seat (Click here)

    HINT:
    Perform the inspection using parts from a normal vehicle when possible.


NEXT


6.PERFORM ZERO POINT CALIBRATION
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the intelligent tester, perform the zero point calibration (Click here).



NG
Go to step 9
OK


7.PERFORM SENSITIVITY CHECK
  1. Using the intelligent tester, perform the sensitivity check (Click here).

    Standard range:
    27 to 33 kg (59.5 to 72.8 lb)



NG
Go to step 9
OK


8.CHECK FOR DTCs
  1. Connect the connectors to the occupant classification ECU and the rear occupant detection sensor RH.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear any DTCs stored in the memory (Click here).

    HINT:
    1. First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.
    2. Use the intelligent tester to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the intelligent tester, check for DTCs of the occupant classification ECU (Click here).

    OK:
    DTC B1788 is not output.

    HINT:
    DTCs other than DTC B1788 may be output at this time, but they are not related to this check.



NG
Go to step 9
OK

END 

9.REPLACE OCCUPANT CLASSIFICATION ECU
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Replace the occupant classification ECU (Click here).

    HINT:
    Perform the inspection using parts from a normal vehicle when possible.


NEXT


10.PERFORM ZERO POINT CALIBRATION
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Using the intelligent tester, perform the zero point calibration (Click here).


NEXT


11.PERFORM SENSITIVITY CHECK
  1. Using the intelligent tester, perform the sensitivity check (Click here).

    Standard range:
    27 to 33 kg (59.5 to 72.8 lb)


NEXT

END