Home › Audio / Visual / Telematics › AUDIO / VIDEO › REAR SEAT ENTERTAINMENT SYSTEM

DTC    B15D5    Rear Seat Entertainment System Disconnected

for Preparation Click here


DESCRIPTION

  1. *1: w/ Navigation System
  2. *2: w/o Navigation System
The navigation receiver assembly*1 or radio and display receiver assembly*2 and television display assembly are connected by the AVC-LAN communication line.
When an AVC-LAN communication error occurs between the navigation receiver assembly*1 or radio and display receiver assembly*2 and television display assembly, this DTC will be stored.

DTC Code
DTC Detection Condition
Trouble Area
B15D5
When either condition below is met:
  1. The television display assembly is/was not connected while the ignition switch is ON or ACC.
  2. Communication between the master unit and the television display assembly is not possible when the engine is started.
  1. AVC-LAN communication line
  2. Television display assembly
  3. Navigation receiver assembly*1
  4. Radio and display receiver assembly*2
  5. Harness or connector

HINT:
  1. Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.
  2. The navigation receiver assembly*1 or radio and display receiver assembly*2 is the master unit.


WIRING DIAGRAM


E260335E07


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses and relays for circuits related to this system before performing the following inspection procedure.

1.CHECK DTC
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same DTC is output again (Click here).

    OK:
    DTC B15D5 is not output.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)  

2.CHECK CONNECTOR CONNECTION CONDITION
  1. Check that the television display assembly and navigation receiver assembly*1 or radio and display receiver assembly*2 connectors are connected properly.

    1. *1: w/ Navigation System
    2. *2: w/o Navigation System

    OK:
    The connectors are connected properly.



NG
CONNECT CONNECTOR CORRECTLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY - BATTERY AND BODY GROUND)


    E192430E62
  1. Disconnect the television display assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    U13-17 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    U13-1 (+B) - Body ground
    Always
    11 to 14 V
    U13-2 (ACC) - Body ground
    Ignition switch ACC
    11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Television Display Assembly)
Result 
Result
Proceed to
OK (w/ Navigation System)
A
OK (w/o Navigation System)
B
NG
C


B
Go to step 6

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A


4.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - TELEVISION DISPLAY ASSEMBLY)
  1. Disconnect the I46 navigation receiver assembly connector.

  1. Disconnect the U13 television display assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I46-9 (TXM+) - U13-3 (TX1+)
    Always
    Below 1 Ω
    I46-10 (TXM-) - U13-4 (TX1-)
    Always
    Below 1 Ω
    I46-9 (TXM+) - Body ground
    Always
    10 kΩ or higher
    I46-10 (TXM-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK TELEVISION DISPLAY ASSEMBLY
  1. Temporarily replace the television display assembly with a new or normally functioning one (Click here).

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same DTC is output again.

    OK:
    DTC B15D5 is not output.



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK

END (TELEVISION DISPLAY ASSEMBLY WAS DEFECTIVE) 

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEVISION DISPLAY ASSEMBLY)
  1. Disconnect the I57 radio and display receiver assembly connector.

  1. Disconnect the U13 television display assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I57-9 (TXM+) - U13-3 (TX1+)
    Always
    Below 1 Ω
    I57-10 (TXM-) - U13-4 (TX1-)
    Always
    Below 1 Ω
    I57-9 (TXM+) - Body ground
    Always
    10 kΩ or higher
    I57-10 (TXM-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK TELEVISION DISPLAY ASSEMBLY
  1. Temporarily replace the television display assembly with a new or normally functioning one (Click here).

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same DTC is output again.

    OK:
    DTC B15D5 is not output.



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK

END (TELEVISION DISPLAY ASSEMBLY WAS DEFECTIVE)