Home › Drivetrain ยท AB60F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION ASSEMBLY

AUTOMATIC TRANSMISSION ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL TRANSFER ASSEMBLY


    C160352
  1. Install the transfer with the 8 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    NOTICE:
    Take care not to damage the rear adaptor oil seal with the transfer input gear spline.



2. INSTALL TORQUE CONVERTER CLUTCH ASSEMBLY


C203634E01
  1. Using a vernier caliper and straightedge, measure dimension A between the transmission fitting surface of the engine *1 and the torque converter fitting surface of the drive plate *2 (step 1)



    C150409E01
  1. Aligning the matchmarks on the transmission case and torque converter clutch, and then mesh the splines of the input shaft and turbine runner.



    C150410E01
  1. Mesh the splines of the stator shaft and stator while turning the torque converter clutch.

    HINT:
    Turn the torque converter clutch approximately 180°.



    C150411E01
  1. Turn the torque converter clutch and align the matchmarks on the torque converter clutch and transmission case to mesh the key of the oil pump drive gear into the slot on the torque converter clutch.

    NOTICE:
    Do not push on the torque converter when aligning the matchmarks.



    C193839E02
  1. Using a vernier caliper and straightedge, measure dimension B shown in the illustration and check that B is more than A (measured in step 1).

    Standard distance:
    A + 1 mm (0.0394 in.) or more



3. INSTALL TRANSMISSION CONTROL CABLE BRACKET


    C161369
  1. Install the transmission control cable bracket with the 2 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



4. INSTALL CONNECTOR CLAMP BRACKET
  1. Install the front left bank oxygen sensor connector clamp bracket with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Install the rear left bank oxygen sensor connector clamp bracket with the bolt.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }

  1. Install the front right bank oxygen sensor connector clamp bracket with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



5. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY


C196694E01
  1. Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter clutch centerpiece.

    Clutch spline grease:
    Toyota Genuine Clutch Spline Grease or equivalent
    Maximum grease amount:
    Approximately 1 g (0.0353 oz.)



    C212462E01
  1. Confirm that the 2 knock pins are on the transaxle contact surface of the engine block before transaxle installation.

  1. Install the transmission with the 10 bolts.

    Torque:
    for 17 mm head bolt A:
    71 N*m{ 724 kgf*cm , 52 ft.*lbf }
    for 14 mm head bolt B:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



6. CONNECT BREATHER PLUG HOSE


    C161365
  1. Connect the 3 breather plug hoses to the harness clamp bracket.



7. CONNECT WIRE HARNESS AND CONNECTOR


    C161361E02
  1. Connect the park/neutral position switch connector, 2 transmission wire connectors and 2 speed sensor connectors.

    HINT:
    Push up the lever until the claw of the transmission wire connector makes a connection sound.

  1. Connect the harness clamp with the bolt.

    Torque:
    8.2 N*m{ 84 kgf*cm , 73 in.*lbf }

  1. Connect the 3 connector clamps and 7 harness clamps.

  1. Tilt up the automatic transmission.



    C155915
  1. Connect the ground cable with the bolt.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



8. INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR


    C220065
  1. Install the rear No. 1 engine mounting insulator to the transmission with the 4 bolts.

    Torque:
    59 N*m{ 602 kgf*cm , 44 ft.*lbf }



9. INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY


    C162565
  1. Install the No. 3 frame crossmember to the rear engine mounting insulator with the 4 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



    C162566
  1. Install the No. 3 frame crossmember with the 4 bolts, 4 washers and 4 nuts.

    Torque:
    110 N*m{ 1122 kgf*cm , 81 ft.*lbf }



10. INSTALL DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT


    C161354
  1. Turn the crankshaft to gain access to the 6 bolts and install the bolts while holding the crankshaft pulley set bolt with a wrench.

    Torque:
    53 N*m{ 535 kgf*cm , 39 ft.*lbf }

    NOTICE:
    First install the black colored bolt and then the remaining 5 bolts.



11. INSTALL STARTER ASSEMBLY
  1. Install the starter assembly (Click here).



12. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


    C162141E01
  1. Connect the transmission control cable with a new clip and nut.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    NOTICE:
    When connecting the cable to the transmission control shaft lever, make sure the cable's L bracket faces the outside of the vehicle.



13. CONNECT WATER BY-PASS PIPE ASSEMBLY


    C162140E03
  1. Connect the 2 water by-pass hoses with the 2 clips and install the water by-pass pipe with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

    HINT:
    Make sure the pinching portion of each clip is facing the direction shown in the illustration.



14. CONNECT NO. 2 OIL COOLER HOSE


    C162129E01
  1. Connect the inlet No. 2 oil cooler hose and outlet No. 2 oil cooler hose with the 2 clips.



15. INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY


A184304
  1. Install a new gasket and the front No. 2 exhaust pipe sub-assembly to the exhaust manifold LH with 3 new nuts.

    Torque:
    54 N*m{ 554 kgf*cm , 40 ft.*lbf }



    A184981
  1. Connect the front No. 3 exhaust pipe sub-assembly to the exhaust pipe support.

  1. Install 2 new gaskets and the front No. 3 exhaust pipe sub-assembly with the 4 bolts and 2 new nuts.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

  1. Connect the air fuel ratio sensor connector.

  1. Connect the heated oxygen sensor connector.



16. INSTALL FRONT EXHAUST PIPE ASSEMBLY


A184982
  1. Install a new gasket and the front exhaust pipe assembly to the exhaust manifold RH with 3 new nuts.

    Torque:
    54 N*m{ 554 kgf*cm , 40 ft.*lbf }

  1. Install a new gasket and the front exhaust pipe assembly to the center exhaust pipe assembly with the 2 bolts.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

  1. Connect the air fuel ratio sensor connector.

  1. Connect the heated oxygen sensor connector and attach the 2 clamps.



17. INSTALL PROPELLER SHAFT ASSEMBLY
  1. Install the propeller shaft assembly (Click here).



18. INSTALL FRONT PROPELLER SHAFT ASSEMBLY
  1. Install the front propeller shaft assembly (Click here).



19. ADD ENGINE COOLANT
  1. Add engine coolant.

    Standard Capacity:
    14.6 liters (15.4 US qts., 12.8 Imp. qts.)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).
    2. Please contact your Toyota dealer for further details.



    A151850E05
  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Install the reservoir cap.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.

  1. Install the radiator cap.

  1. Start the engine and warm it up until the thermostat opens.

    HINT:
    The thermostat opening timing can be confirmed by pressing the radiator inlet hose by hand, and checking when the engine coolant starts to flow inside the hose.

  1. Maintain the engine speed at 2000 to 2500 rpm.

    NOTICE:
    1. Make sure that the radiator reservoir still has some coolant in it.
    2. Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
    3. If there is not enough coolant, the engine may burn out or overheat.
    4. Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the FULL line.
    5. Run the engine at 2000 rpm until the coolant level has stabilized.

  1. Press the inlet and outlet radiator hoses several times by hand to bleed air.

    CAUTION:
    1. Wear protective gloves.
    2. Be careful as the radiator hoses are hot.
    3. Keep your hands away from the fan.

  1. Stop the engine, and wait until the engine coolant cools down to ambient temperature.

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A161780E01
  1. Check that the coolant level is between the FULL and LOW lines.
    If the coolant level is below the LOW line, repeat all of the procedures above.
    If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW lines.



20. ADD TRANSFER OIL
  1. Install a new gasket and the drain plug.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Pour oil so that the oil level is between 0 to 5.0 mm (0 to 0.197 in.) from the bottom lip of the filler plug hole.

    NOTICE:
    1. Pour oil slowly.
    2. Pour oil a little at a time, waiting several minutes between each addition of oil.

  1. Wait approximately 5 minutes and check that the oil level has not changed.

  1. Install a new gasket and the filler plug.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



    C159809
  1. Install the lower transfer case protector with the 4 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



21. ADD AUTOMATIC TRANSMISSION FLUID
  1. Add automatic transmission fluid (Click here).



22. INSPECT FOR AUTOMATIC TRANSMISSION FLUID LEAK


23. INSPECT FOR TRANSFER OIL LEAK


24. INSPECT FOR ENGINE COOLANT LEAK


A161766E01

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.



25. INSPECT FOR EXHAUST GAS LEAK
If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.


26. INSPECT SHIFT LEVER POSITION
  1. When moving the shift lever from P to R with the ignition switch ON and the brake pedal depressed, make sure that it moves smoothly and correctly into position.

  1. Check that the shift lever does not stop when moving the shift lever from R to P, and check that the shift lever does not stick when moving the shift lever from D to S.

  1. Start the engine and make sure that the vehicle moves forward after moving the shift lever from N to D and moves rearward after moving the shift lever to R.
    If the operation cannot be done as specified, inspect the park/neutral position switch assembly and check the shift lever assembly installation condition.



27. ADJUST SHIFT LEVER POSITION
  1. Move the shift lever to the N position.



    C155901E02
  1. Fold back the transmission control cable adjust case cover. Then while sliding the slider toward the cable end side, press the lock piece from the back side to release the lock.



    C155902E02
  1. Check that the adjust case's spring is applying enough tension to the shift control cable. Then press the lock piece to set the lock.

    NOTICE:
    1. Use your hand to push the lock piece. Do not use any tools.
    2. Securely push the lock piece so that the slider's protrusion is above the lock piece.

  1. Return the cover of the adjust case to its original position.

  1. Inspect the operation after the adjustment.



28. RESET MEMORY
  1. Perform the Reset Memory procedures (A/T initialization) (Click here).