Home › Suspension › SUSPENSION CONTROL › AIR SUSPENSION SYSTEM (w/ AVS)

DTC    C1761    Continuous Electric Current to Height Control Compressor Motor

for Preparation Click here


DESCRIPTION


DTC Code
Detection Condition
Trouble Area
C1761*1
Either condition is met:
  1. With the AIR SUS relay activated, the vehicle does not return to the standard vehicle height after 90 seconds have elapsed.
  2. Power is supplied to the height control compressor motor for 100 seconds or more within a 280 second period.
  1. Air leakage from the air tube or each valve
  2. Clogging in the air tube or each valve
  3. AIR SUS relay
  4. Leveling solenoid valve (No. 2 height control valve)
  5. Gate solenoid valve (No. 2 height control valve)
  6. Exhaust solenoid valve (No. 1 height control compressor)
  7. Height control sensors
  8. Wire harness or connector
  9. Height control compressor
  10. Suspension control ECU

HINT:
*1: The compressor motor operates continuously to raise vehicle height and allows electric current flow to the AIR SUS relay for 90 seconds or more under the following conditions:
  1. Vehicle height control is attempted on a steep slope when the vehicle is overloaded.
  2. The compressor remains on for an excessive period of time or repeatedly turns on and off because of continuous height control switch operation.
  3. If the compressor remains on because the vehicle is jacked up, the vehicle height is set at a position lower than normal while the engine is running and then the vehicle height control function raises the vehicle.
    Thus DTC C1761 may be output and vehicle height control may be suspended. (This is not electrically abnormal.) In this case, however, the vehicle height operation is resumed approximately 10 minutes after the ignition switch is turned ON after the ECU detects the first error. If the ECU detects another error, it takes 70 minutes until control is resumed.


WIRING DIAGRAM


C179533E04


INSPECTION PROCEDURE

NOTICE:
After replacing the suspension control ECU, perform registration (Click here).

1.INSPECT FOR AIR LEAK
  1. Check for air leakage .

    OK:
    No leaks.



NG
REPAIR OR REPLACE AIR TUBE
OK


2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (EXHAUST SOLENOID)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON, and turn the intelligent tester on.

  1. Enter the following menus: Chassis / Air suspension / Active Test.

    Air Suspension 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Exhaust Solenoid
    Exhaust solenoid valve
    ON or OFF
    Operation sound of solenoid (clicking sound) can be heard

    OK:
    Operation of solenoid (clicking sound) can be heard



NG
REPLACE NO. 1 HEIGHT CONTROL COMPRESSOR (Click here)
OK


3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (REAR GATE SOLENOID)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON, and turn the intelligent tester on.

  1. Enter the following menus: Chassis / Air suspension / Active Test.

    Air Suspension 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Rear Gate Solenoid
    Gate solenoid valve/
    ON or OFF
    Operation sound of solenoid (clicking sound) can be heard

    OK:
    Operation of solenoid (clicking sound) can be heard



NG
REPLACE NO. 2 HEIGHT CONTROL VALVE SUB-ASSEMBLY (Click here)
OK


4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (REAR LEVELING SOLENOID)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON, and turn the intelligent tester on.

  1. Enter the following menus: Chassis / Air suspension / Active Test.

    Air Suspension 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Rear Leveling Solenoid
    Leveling solenoid valve
    ON or OFF
    Operation sound of solenoid (clicking sound) can be heard

    OK:
    Operation of solenoid (clicking sound) can be heard



NG
REPLACE NO. 2 HEIGHT CONTROL VALVE SUB-ASSEMBLY (Click here)
OK


5.INSPECT SUSPENSION CONTROL RELAY (AIR SUS)


    C149624E16
  1. Turn the ignition switch off.

  1. Remove the AIR SUS relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    When 12 V battery voltage is not applied to terminal 1 and 2
    10 kΩ or higher
    When 12 V battery voltage is applied to terminal 1 and 2
    Below 1 Ω



NG
REPLACE SUSPENSION CONTROL RELAY
OK


6.CHECK HARNESS AND CONNECTOR (COMPRESSOR - BATTERY AND BODY GROUND)


    C179505E01
  1. Remove the AIR SUS relay from the engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Relay block AIR SUS relay terminal 5 - Body ground
    Always
    11 to 14 V

  1. Disconnect the Q7 compressor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Relay block AIR SUS relay terminal 3 - Q7-1 (B)
    Always
    Below 1 Ω
    Relay block AIR SUS relay terminal 3 or Q7-1 (B) - Body ground
    Always
    10 kΩ or higher
    Q7-2 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK VEHICLE HEIGHT
  1. Check the vehicle height (Click here).



NG
ADJUST VEHICLE HEIGHT (Click here)
OK


8.CHECK FOR DTC
  1. Clear the DTC (Click here).

  1. Check for DTC (Click here).
    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE SUSPENSION CONTROL ECU (Click here)