Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1232/32    Stuck in Deceleration Sensor

DTC    C1234/34    Yaw Rate Sensor Malfunction

DTC    C1244/44    Open or Short in Deceleration Sensor Circuit

DTC    C1279/79    Deceleration Sensor Output Voltage Malfunction (Test Mode DTC)

for Preparation Click here


DESCRIPTION

The skid control ECU receives signals from the yaw rate and deceleration sensor via the CAN communication system.
The yaw rate sensor has a built-in deceleration sensor.
If there is trouble in the bus lines between the yaw rate sensor and skid control ECU, DTC U0123/62 (malfunction in CAN communication with the yaw rate sensor) and U0124/69 (malfunction in CAN communication with the deceleration sensor) are output.
DTC C1279/79 is cleared when the yaw rate sensor sends a deceleration signal failure in test mode. DTC C1279/79 is using only in test mode.

DTC Code
DTC Detection Condition
Trouble Area
C1232/32
When any of following conditions detected:
  1. Malfunctions in deceleration sensor detected through self-diagnosis.
  2. Malfunctions in deceleration sensor circuit detected.
  3. Power supply to deceleration sensor abnormal (less than 6.5 V or 18 V or higher).
  4. When ignition switch turned ON, short between deceleration sensor power supply and either ground or battery.
  1. Yaw rate sensor
  2. Yaw rate sensor circuit
  3. VSC actuator (skid control ECU)
C1234/34
Sensor malfunction signal received from yaw rate sensor
  1. Yaw rate sensor
  2. Yaw rate sensor circuit
  3. VSC actuator (skid control ECU)
C1244/44
G sensor output representing vehicle forward and rearward acceleration is abnormal
  1. Yaw rate sensor
  2. Yaw rate sensor circuit
  3. Skid control ECU
C1279/79
Detected only during test mode
  1. Yaw rate sensor
  2. Yaw rate sensor circuit
  3. VSC actuator (skid control ECU)

WIRING DIAGRAM


C129349E09


INSPECTION PROCEDURE

HINT:
When U0123/62, U0124/69 or U0126/63 is output together with C1232/32, C1234/34 or C1244/44, inspect and repair the trouble areas indicated by U0123/62, U0124/69 or U0126/63 first.

NOTICE:
When replacing the VSC actuator assembly, perform zero point calibration (Click here).

1.CHECK DTC
  1. Clear the DTC(s) (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON again and check that no CAN communication system DTC(s) is output.

  1. Drive the vehicle at a speed of 30 km/h (19 mph) or more and check that no DTCs are output.
    Result 
    Result
    Proceed to
    DTC is output (relating to yaw rate and deceleration sensor)
    A
    DTC is output (relating to CAN communication system)
    B
    DTC is not output
    C



B
GO TO CAN COMMUNICATION SYSTEM (Click here)

C
CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)
A


2.CHECK YAW RATE SENSOR INSTALLATION


    C162545E01
  1. Check that the yaw rate sensor has been installed correctly.

    Torque:
    13 N*m (127 kgf*cm, 9 ft.*lbf)

    OK:
    The sensor is tightened to the specified torque.
    The sensor is not tilted.

    NOTICE:
    Do not use an electric impact wrench to tighten the yaw rate sensor bolts because the sensor is sensitive to vibration.



NG
INSTALL YAW RATE SENSOR CORRECTLY (Click here)
OK


3.INSPECT YAW RATE SENSOR
  1. Remove the 2 nuts of the sensor bracket and yaw rate sensor with the connector connected .

  1. Connect the intelligent tester to the DLC3.

  1. Turn the intelligent tester ON.

  1. Select the Data List mode on the intelligent tester.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Deceleration Sensor2
    Acceleration sensor 2 reading /
    min.: -18.183 m/s2, max.: 18.183 m/s2
    Approximately -1.28 to 1.27 m/s2
    while stationary
    Reading changes when vehicle is bounced.



    C129363
  1. Place the yaw rate sensor as shown in the illustration and turn the sensor to the right and left.

  1. Check that the deceleration value of the deceleration sensor displayed on the intelligent tester changes.

    OK:
    Deceleration value changes.



NG
REPLACE YAW RATE SENSOR (Click here)
OK


4.CHECK YAW RATE SENSOR TERMINAL VOLTAGE
  1. for 2WD: Disconnect the O11 sensor connector.

  1. for 4WD: Disconnect the O12 sensor connector.

  1. Turn the ignition switch to ON.



    C161766E05
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for 2WD 
    Tester Connection
    Switch Condition
    Specified Condition
    O11-3 (VYS) - O11-5 (GYAW)
    Ignition switch ON
    11 to 14 V
    for 4WD 
    Tester Connection
    Switch Condition
    Specified Condition
    O12-3 (VYS) - O12-5 (GYAW)
    Ignition switch ON
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 2WD 
    Tester Connection
    Switch Condition
    Specified Condition
    O11-5 (GYAW) - Body ground
    Ignition switch ON
    Below 1 Ω
    for 4WD 
    Tester Connection
    Switch Condition
    Specified Condition
    O12-5 (GYAW) - Body ground
    Ignition switch ON
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE VSC ACTUATOR ASSEMBLY (Click here)