Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM

POWER BACK DOOR SYSTEM > Touch Sensor Circuit

for Preparation Click here


DESCRIPTION

When the power back door ECU receives a jam signal from the touch sensor while the power back door closer is operating, the ECU reverses the back door operation and opens the door.

WIRING DIAGRAM


B165200E16


INSPECTION PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (POWER BACK DOOR TOUCH SENSOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Back Door / Data List.

  1. According to the display on the intelligent tester, read the Data List.

    Back Door 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    PBD Touch Sen L
    Power back door touch sensor LH signal / ON or OFF
    ON: Power back door touch sensor LH is pressed
    OFF: Power back door touch sensor LH is not pressed
    -
    PBD Touch Sen R
    Power back door touch sensor RH signal / ON or OFF
    ON: Power back door touch sensor RH is pressed
    OFF: Power back door touch sensor RH is not pressed
    -

    OK:
    The display is as specified in the normal condition.



NG
Go to step 2
OK

REPLACE POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU) (Click here)  

2.INSPECT POWER BACK DOOR TOUCH SENSOR


    B220012E03
  1. Remove the power back door touch sensor (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (OSL) - 2 (OSLE)*1
    Not pressed
    950 to 1050 Ω
    1 (OSL) - 2 (OSLE)*1
    Pressed
    Below 100 Ω
    1 (OSR) - 2 (OSRE)*2
    Not pressed
    950 to 1050 Ω
    1 (OSR) - 2 (OSRE)*2
    Pressed
    Below 100 Ω

*1: for LH Side
*2: for RH Side


NG
REPLACE POWER BACK DOOR TOUCH SENSOR (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (POWER BACK DOOR TOUCH SENSOR - POWER BACK DOOR DRIVE UNIT AND BODY GROUND)


    B220013E01
  1. for LH Side:

    1. Disconnect the V15 sensor connector.

    2. Disconnect the O30 ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      V15-1 (OSL) - O30-15 (OSL)
      Always
      Below 1 Ω
      V15-2 (OSLE) - O30-14 (OSE)
      Always
      Below 1 Ω
      V15-1 (OSL) - Body ground
      Always
      10 kΩ or higher
      V15-2 (OSLE) - Body ground
      Always
      Below 1 Ω



    B220013E02
  1. for RH Side:

    1. Disconnect the V14 sensor connector.

    2. Disconnect the O30 ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      V14-1 (OSR) - O30-13 (OSR)
      Always
      Below 1 Ω
      V14-2 (OSRE) - O30-14 (OSE)
      Always
      Below 1 Ω
      V14-1 (OSR) - Body ground
      Always
      10 kΩ or higher
      V14-2 (OSRE) - Body ground
      Always
      Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU) (Click here)