POWER MIRROR CONTROL SYSTEM (w/ Memory) > Power Mirrors do not Return to Memorized Position |

| 1.CHECK FOR DTC |
Use the intelligent tester to check if the CAN communication system is functioning normally (Click here).
| Result | Proceed to |
| CAN DTC is not output | A |
| CAN DTC is output | B |
|
| ||||
| A | |
| 2.CHECK POWER MIRROR CONTROL FUNCTION |
Check that the mirror surface positions of the outer rear view mirror LH and RH can be moved using the outer mirror switch.
|
| ||||
| OK | |
| 3.READ VALUE USING INTELLIGENT TESTER (MIRROR POSITION MEMORY) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Mirror / Data List.
According to the display on the intelligent tester, read the Data List.
| Tester Display | Measurement Item/Display | Normal Condition | Diagnostic Note |
| Mirror Memory No. 1 | Mirror position memorized in seat memory switch 1 / ON or OFF | ON: Memorized OFF: Not memorized | - |
| Mirror Memory No. 2 | Mirror position memorized in seat memory switch 2 / ON or OFF | ON: Memorized OFF: Not memorized | - |
|
| ||||
| OK | |
| 4.READ VALUE USING INTELLIGENT TESTER (MIRROR POSITION SENSOR) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Mirror / Data List.
According to the display on the intelligent tester, read the Data List.
| Tester Display | Measurement Item/Display | Normal Condition | Diagnostic Note |
| RH Mir Position Sensor V | Passenger side mirror vertical sensor voltage / MIN: 0 V, MAX: 5 V | Within range from 0 to 5 V | - |
| RH Mir Position Sensor H | Passenger side mirror horizontal sensor voltage / MIN: 0 V, MAX: 5 V | Within range from 0 to 5 V | - |
| LH Mir Position Sensor V | Driver side mirror vertical sensor voltage / MIN: 0 V, MAX: 5 V | Within range from 0 to 5 V | - |
| LH Mir Position Sensor H | Driver side mirror horizontal sensor voltage / MIN: 0 V, MAX: 5 V | Within range from 0 to 5 V | - |
| Result | Proceed to |
| LH side mirror does not operate normally | A |
| RH side mirror does not operate normally | B |
| Mirror operates normally | C |
|
| ||||
|
| ||||
| A | |
| 5.CHECK OUTER MIRROR CONTROL ECU |
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| M8-2 (VC) - M8-3 (E1) | Ignition switch ON | 3.5 to 5.5 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M8-3 (E1) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR LH - OUTER MIRROR CONTROL ECU) |
![]() |
Disconnect the M8 ECU connector.
Disconnect the M5 mirror connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M5-15 (VC) - M8-2 (VC) | Always | Below 1 Ω |
| M5-15 (VC) - Body ground | Always | 10 kΩ or higher |
| M5-16 (HSRL) - M8-5 (HSRL) | Always | Below 1 Ω |
| M5-16 (HSRL) - Body ground | Always | 10 kΩ or higher |
| M5-17 (VSRL) - M8-4 (VSR) | Always | Below 1 Ω |
| M5-17 (VSRL) - Body ground | Always | 10 kΩ or higher |
| M5-18 (E1) - M8-3 (E1) | Always | Below 1 Ω |
| M5-18 (E1)- Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 7.CHECK OUTER MIRROR CONTROL ECU |
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| M8-22 (VC) - M8-23 (E1) | Ignition switch ON | 3.5 to 5.5 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M8-23 (E1) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR RH - OUTER MIRROR CONTROL ECU) |
![]() |
Disconnect the M8 ECU connector.
Disconnect the L6 mirror connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| L6-15 (VC) - M8-22 (VC) | Always | Below 1 Ω |
| L6-15 (VC) - Body ground | Always | 10 kΩ or higher |
| L6-16 (HSSR) - M8-25 (HSRR) | Always | Below 1 Ω |
| L6-16 (HSSR) - Body ground | Always | 10 kΩ or higher |
| L6-17 (VSSR) - M8-24 (VSRR) | Always | Below 1 Ω |
| L6-17 (VSSR) - Body ground | Always | 10 kΩ or higher |
| L6-18 (E1) - M8-23 (E1) | Always | Below 1 Ω |
| L6-18 (E1)- Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||