Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM

DTC    B1820/55    Short in Front Driver Side - Side Squib Circuit

DTC    B1821/55    Open in Front Driver Side - Side Squib Circuit

DTC    B1822/55    Short to GND in Front Driver Side - Side Squib Circuit

DTC    B1823/55    Short to B+ in Front Driver Side - Side Squib Circuit

for Preparation Click here


DESCRIPTION

The side squib LH circuit consists of the center airbag sensor and the front seat side airbag LH.
The circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the side squib LH circuit.

DTC Code
Detection Condition
Trouble Area
B1820/55
When one of following conditions is met:
  1. The center airbag sensor receives a line short circuit signal 5 times in the side squib LH circuit during primary check.
  2. Side squib LH malfunction
  3. Center airbag sensor malfunction
  1. Floor wire
  2. Front seat side airbag assembly LH (Side squib LH)
  3. Center airbag sensor assembly
B1821/55
When one of following conditions is met:
  1. The center airbag sensor receives an open circuit signal in the side squib LH circuit for 2 seconds.
  2. Side squib LH malfunction
  3. Center airbag sensor malfunction
  1. Floor wire
  2. Front seat side airbag assembly LH (Side squib LH)
  3. Center airbag sensor assembly
B1822/55
When one of following conditions is met:
  1. The center airbag sensor receives a short circuit to ground signal in the side squib LH circuit for 0.5 seconds.
  2. Side squib LH malfunction
  3. Center airbag sensor malfunction
  1. Floor wire
  2. Front seat side airbag assembly LH (Side squib LH)
  3. Center airbag sensor assembly
B1823/55
When one of following conditions is met:
  1. The center airbag sensor receives a short circuit to B+ signal in the side squib LH circuit for 0.5 seconds.
  2. Side squib LH malfunction
  3. Center airbag sensor malfunction
  1. Floor wire
  2. Front seat side airbag assembly LH (Side squib LH)
  3. Center airbag sensor assembly

WIRING DIAGRAM


C180215E03


INSPECTION PROCEDURE

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).
  2. When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).

HINT:
  1. Perform the simulation method by selecting "check mode" (signal check) with the intelligent tester (Click here).
  2. After selecting "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on various types of roads (Click here).

1.CHECK CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connector is properly connected to the front seat side airbag LH.

    OK:
    The connector is properly connected.

    HINT:
    If the connector is not connected securely, reconnect the connector and proceed to the next inspection.

  1. Disconnect the connector from the front seat side airbag LH.

  1. Check that the terminal of the connector is not damaged.

    OK:
    The terminal is not deformed or damaged.



NG
REPLACE FLOOR WIRE
OK


2.CHECK FRONT SEAT SIDE AIRBAG LH (SEAT AIRBAG WIRE LH)
C162330E03
  1. Connect the black wire side of SST (resistance: 2.1 Ω) to connector C.

    CAUTION:
    Never connect the tester to the front seat side airbag LH (side squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting SST.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1820, B1821, B1822, B1823 or 55 is output
    A
    DTC B1820, B1821, B1822, B1823 or 55 is not output (w/ Manual Seat)
    B
    DTC B1820, B1821, B1822, B1823 or 55 is not output (w/ Power Seat)
    C

    HINT:
    Codes other than DTC B1820, B1821, B1822, B1823 and 55 may be output at this time, but they are not related to this check.



B
REPLACE FRONT SEAT ASSEMBLY LH (Click here)

C
REPLACE FRONT SEAT ASSEMBLY LH (Click here)
A


3.CHECK CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect SST from connector C.

  1. Check that the connector is properly connected to the center airbag sensor assembly.

    OK:
    The connector is properly connected.

  1. Disconnect the connector from the center airbag sensor assembly.

  1. Check that the terminal of the connector is not damaged.

    OK:
    The terminal is not deformed or damaged.

  1. Check that the short spring for the floor wire connector with the activation prevention mechanism is not deformed or damaged.

    OK:
    The short spring is not deformed or damaged.



NG
REPLACE FLOOR WIRE
OK


4.CHECK FLOOR WIRE (SIDE SQUIB LH CIRCUIT)
C158867E05
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    O6-1 (SFL+) - Body ground
    Ignition switch ON
    Below 1 V
    O6-2 (SFL-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O6-1 (SFL+) - O6-2 (SFL-)
    Always
    Below 1 Ω

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O6-1 (SFL+) - O6-2 (SFL-)
    Always
    1 MΩ or higher
    O6-1 (SFL+) - Body ground
    Always
    1 MΩ or higher
    O6-2 (SFL-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE FLOOR WIRE
OK


5.CHECK CENTER AIRBAG SENSOR
C158868E03
  1. Restore the released activation prevention mechanism of connector B to the original condition.

  1. Connect the connectors to the front seat side airbag LH and the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1820, B1821, B1822, B1823 or 55 is not output.

    HINT:
    Codes other than DTC B1820, B1821, B1822, B1823 and 55 may be output at this time, but they are not related to this check.

    Result 
    Result
    Proceed to
    OK
    A
    NG (w/ Cool Box)
    B
    NG (w/o Cool Box)
    C



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)