Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM

DTC    B1900/73    Short in Front Driver Side Pretensioner Squib Circuit

DTC    B1901/73    Open in Front Driver Side Pretensioner Squib Circuit

DTC    B1902/73    Short to GND in Front Driver Side Pretensioner Squib Circuit

DTC    B1903/73    Short to B+ in Front Driver Side Pretensioner Squib Circuit

for Preparation Click here


DESCRIPTION

The front pretensioner squib LH circuit consists of the center airbag sensor and the front seat outer belt LH.
This circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the front pretensioner squib LH circuit.

DTC Code
Detection Condition
Trouble Area
B1900/73
When one of following conditions is met:
  1. The center airbag sensor receives a line short circuit signal 5 times in the front pretensioner squib LH circuit during primary check.
  2. Front pretensioner squib LH malfunction
  3. Center airbag sensor malfunction
  1. Floor wire
  2. Front seat outer belt assembly LH (Front pretensioner squib LH)
  3. Center airbag sensor assembly
B1901/73
When one of following conditions is met:
  1. The center airbag sensor receives an open circuit signal in the front pretensioner squib LH circuit for 2 seconds.
  2. Front pretensioner squib LH malfunction
  3. Center airbag sensor malfunction
  1. Floor wire
  2. Front seat outer belt assembly LH (Front pretensioner squib LH)
  3. Center airbag sensor assembly
B1902/73
When one of following conditions is met:
  1. The center airbag sensor receives a short circuit to ground signal in the front pretensioner squib LH circuit for 0.5 seconds.
  2. Front pretensioner squib LH malfunction
  3. Center airbag sensor malfunction
  1. Floor wire
  2. Front seat outer belt assembly LH (Front pretensioner squib LH)
  3. Center airbag sensor assembly
B1903/73
When one of following conditions is met:
  1. The center airbag sensor receives a short circuit to B+ signal in the front pretensioner squib LH circuit for 0.5 seconds.
  2. Front pretensioner squib LH malfunction
  3. Center airbag sensor malfunction
  1. Floor wire
  2. Front seat outer belt assembly LH (Front pretensioner squib LH)
  3. Center airbag sensor assembly

WIRING DIAGRAM


C157591E59


INSPECTION PROCEDURE

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).
  2. When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).

HINT:
  1. Perform the simulation method by selecting "check mode" (signal check) with the intelligent tester (Click here).
  2. After selecting "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on various types of roads (Click here).

1.CHECK CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connector is properly connected to the front seat outer belt LH.

    OK:
    The connector is properly connected.

    HINT:
    If the connector is not connected securely, reconnect the connector and proceed to the next inspection.

  1. Disconnect the connector from the front seat outer belt LH.

  1. Check that the floor wire connector (on the front seat outer belt LH side) is not damaged.

    OK:
    The lock button is not disengaged, or the claw of the lock is not deformed or damaged.



NG
REPLACE FLOOR WIRE
OK


2.CHECK FRONT SEAT OUTER BELT LH (FRONT PRETENSIONER SQUIB LH)
C168657E02
  1. Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

    CAUTION:
    Never connect the tester to the front seat outer belt LH (front pretensioner squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting SST.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1900, B1901, B1902, B1903 or 73 is not output.

    HINT:
    Codes other than DTC B1900, B1901, B1902, B1903 and 73 may be output at this time, but they are not related to this check.



NG
Go to step 3
OK

REPLACE FRONT SEAT OUTER BELT ASSEMBLY LH (Click here)  

3.CHECK CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect SST from connector C.

  1. Check that the connector is properly connected to the center airbag sensor assembly.

    OK:
    The connector is properly connected.

    HINT:
    If the connector is not connected securely, reconnect the connector and proceed to the next inspection.

  1. Disconnect the connector from the center airbag sensor assembly.

  1. Check that the terminal of the connector is not damaged.

    OK:
    The terminal is not deformed or damaged.

  1. Check that the short spring for the floor wire connector with the activation prevention mechanism is not deformed or damaged.

    OK:
    The short spring is not deformed or damaged.



NG
REPLACE FLOOR WIRE
OK


4.CHECK FLOOR WIRE (FRONT PRETENSIONER SQUIB LH CIRCUIT)
C168658E02
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    O9-1 (L+) - Body ground
    Ignition switch ON
    Below 1 V
    O9-2 (L-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O9-1 (L+) - O9-2 (L-)
    Always
    Below 1 Ω

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O9-1 (L+) - O9-2 (L-)
    Always
    1 MΩ or higher
    O9-1 (L+) - Body ground
    Always
    1 MΩ or higher
    O9-2 (L-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE FLOOR WIRE
OK


5.CHECK CENTER AIRBAG SENSOR
C146268E04
  1. Restore the released activation prevention mechanism of connector B to the original condition.

  1. Connect the connectors to the front seat outer belt LH and the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1900, B1901, B1902, B1903 or 73 is not output.

    HINT:
    Codes other than DTC B1900, B1901, B1902, B1903 and 73 may be output at this time, but they are not related to this check.

    Result 
    Result
    Proceed to
    OK
    A
    NG (w/ Cool Box)
    B
    NG (w/o Cool Box)
    C



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)